That is exactly what has happened, I found one entry that they changed the section field, but not the state and now have to search for the other. Thanks for your support. The software worked great, we had 5 computers networked together using TCP and it worked flawlessly.

Larry  N8CWU

Yes , however, I have carefully checked the log and there is no entry for AK and the AK in the program is still RED
Larry  N8CWU

 

Someone enter AK for AR?  Easy to do, and both are valid sections so program would not catch it.

Dale K8TS

 

 

Sent from Mail for Windows 10

 

From: Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users]
Sent: Tuesday, June 26, 2018 6:24 AM
To: N3FJP_Software_Users@...
Subject: Re: [N3FJP_Software_Users] Questino

 

 

Hi Larry,

 

Thanks for your e-mail.  I don't know how AK could be counted if it is not in your log.  No one has ever reported that before.  The blank lines are contacts for which there is no state.

 

Enjoy!

73, Scott

N3FJP

http://www.n3fjp.com

 

Serving the Amateur Radio community with contesting and general logging software since 1997.

 

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...

 

 

 

-----Original Message-----
From: Roanin roanin2009@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
Sent: Mon, Jun 25, 2018 10:55 pm
Subject: [N3FJP_Software_Users] Questino

 

Scott,

Was wondering if you could explain why in the statistics file generated
by the Field Day program that is shows below under AK as 2 when we did
not work Alaska and I cannot find AK in the program. Also if you look
above the UT there is an entry that has nothing but says we had 4 contacts?

Any Ideas?


Thanks for your support.

Larry  N8CWU

Total Contacts by State \ Prov:

State Total %
----- ----- ---
FL 64 6
OH 64 6
NC 56 6
PA 56 6
GA 55 5
TX 54 5
NY 51 5
VA 45 4
TN 39 4
IL 38 4
MI 38 4
ON 34 3
AL 30 3
MA 30 3
NJ 27 3
SC 27 3
MO 21 2
WI 18 2
IN 17 2
KY 17 2
MD 16 2
MS 16 2
IA 15 1
CA 14 1
NH 13 1
LA 11 1
AR 10 1
OK 10 1
QC 10 1
RI 10 1
CT 9 1
ME 9 1
NE 9 1
VT 7 1
AZ 6 1
KS 6 1
MN 6 1
WV 6 1
CO 5 0
OR 5 0
SD 5 0
4 0 <-----------
UT 4 0
WA 4 0
AK 2 0 <----------
DE 2 0
ID 2 0
NM 2 0
NV 2 0
BC 1 0
NT 1 0

Total = 50

 

Hello again... in the AClog program under the main logging screen not with any settings open use the down arrow to select CW mode  then hit F12 if you have the WinKeyer setup correctly you will get the dialog box that the keyboard keying is enabled. If you do not have WinKey setup correctly you will not get the dialog box or CW Mode is not selected you will not get  the the dialog box. Like I said I did not want to confuse anyone bye for now Bill N3GTY

so how do i switch modes? When i hit f12, my screen reader doesn't
tell me anything.

On 6/26/18, Bill Wagaman wwagaman@charter.net [N3FJP_Software_Users]
<N3FJP_Software_Users@yahoogroups.com> wrote:

Hello Bill here N3GTY lets see if I can confuse you.... if you have the
Winkey configured make sure that AcLog program is in CW as the mode.
Then hit F12 if you see the message that you can type from the keyboard
and your CW is enabled. Again hit F12 to disable it.
That is to enable Keyboard typing for CW you an also set the CW Macros
and use them also. Hope that helps 73 for now Bill

On 6/26/2018 13:17, Jed Barton jed@jedbarton.com [N3FJP_Software_Users]
wrote:

Hey guys,

OK a question. It looks like i have configured the winkeyer in
amateur contact log. So what window should i be in when i want it to
transmit?
I'm in the main window right now where i can tab through the fields to
enter the call and all that. Any ideas?

Thanks,
Jed

--
Bill Wagaman
155 Woodbridge Drive
Spring Lake, NC 28390

Hello Bill here N3GTY lets see if I can confuse you.... if you have the Winkey configured make sure that AcLog program is in CW as the mode. Then hit F12 if you see the message that you can type from the keyboard and your CW is enabled. Again hit F12 to disable it.
That is to enable Keyboard typing for CW you an also set the CW Macros and use them also. Hope that helps 73 for now Bill

 

Hey guys,

OK a question. It looks like i have configured the winkeyer in
amateur contact log. So what window should i be in when i want it to
transmit?
I'm in the main window right now where i can tab through the fields to
enter the call and all that. Any ideas?

Thanks,
Jed

-- 
Bill Wagaman
155 Woodbridge Drive
Spring Lake, NC 28390

so there is a setting in here, my speech program says key on port 1
checkbox not checked, then there is another program that says key on
port 2, checkbox checked. I'mm using com 9. Am i missing something?

On 6/26/18, darkstar7@broadstripe.net [N3FJP_Software_Users]
<N3FJP_Software_Users@yahoogroups.com> wrote:

So you need to make sure that you are getting the message that says
something to the effect "WinKeyer Version XXX opened - success ! " when you
tell it to configure WinKeyer. If you aren't seeing that confirmation, then
WinKeyer is not active. If you're seeing the confirmation, make sure you
have all the desired options checked - correct keying output port, sidetone
enable/disable, speed pot lock/unlock, etc. and then use the "test" button
at the bottom to make sure you're hearing the WinKeyer respond. If it
doesn't respond, then something is amiss. If it does respond (I think it
sends a series of V's, then your call), then click the "done" button to
exit. Do not click the "close" button or you'll turn the WinKeyer off.

73
Mark KN7T

----- Original Message -----

From: "Jed Barton jed@jedbarton.com [N3FJP_Software_Users]"
<N3FJP_Software_Users@yahoogroups.com>
To: "N3FJP Software Users" <N3FJP_Software_Users@yahoogroups.com>
Sent: Tuesday, June 26, 2018 12:05:38 PM
Subject: Re: [N3FJP_Software_Users] winkeyer question on amateur contact log




ok, so there appears to be some sort of issue. I have the com port
set correctly. What else do i need to set in the winkeyer setup? I
just left all of the defaults.

Cheers,
Jed

On 6/26/18, darkstar7@broadstripe.net [N3FJP_Software_Users]
<N3FJP_Software_Users@yahoogroups.com> wrote:

Jed,

You should be in the main log window and you use the F keys to send the
programmed message or exchange if that's what you're after. There are
special characters used to create a message or exchange in the WinKeyer
window (where you define each F key function). Make sure that the WinKeyer

was confirmed "open - success !" before you close that window or it won't

function.

73
Mark KN7T

----- Original Message -----

From: "Jed Barton jed@jedbarton.com [N3FJP_Software_Users]"
<N3FJP_Software_Users@yahoogroups.com>
To: "n3fjp_software_users" <n3fjp_software_users@yahoogroups.com>
Sent: Tuesday, June 26, 2018 10:17:08 AM
Subject: [N3FJP_Software_Users] winkeyer question on amateur contact log



Hey guys,

OK a question. It looks like i have configured the winkeyer in
amateur contact log. So what window should i be in when i want it to
transmit?
I'm in the main window right now where i can tab through the fields to
enter the call and all that. Any ideas?

Thanks,
Jed

ok, so there appears to be some sort of issue. I have the com port
set correctly. What else do i need to set in the winkeyer setup? I
just left all of the defaults.

Cheers,
Jed

On 6/26/18, darkstar7@broadstripe.net [N3FJP_Software_Users]
<N3FJP_Software_Users@yahoogroups.com> wrote:

Jed,

You should be in the main log window and you use the F keys to send the
programmed message or exchange if that's what you're after. There are
special characters used to create a message or exchange in the WinKeyer
window (where you define each F key function). Make sure that the WinKeyer
was confirmed "open - success !" before you close that window or it won't
function.

73
Mark KN7T

----- Original Message -----

From: "Jed Barton jed@jedbarton.com [N3FJP_Software_Users]"
<N3FJP_Software_Users@yahoogroups.com>
To: "n3fjp_software_users" <n3fjp_software_users@yahoogroups.com>
Sent: Tuesday, June 26, 2018 10:17:08 AM
Subject: [N3FJP_Software_Users] winkeyer question on amateur contact log



Hey guys,

OK a question. It looks like i have configured the winkeyer in
amateur contact log. So what window should i be in when i want it to
transmit?
I'm in the main window right now where i can tab through the fields to
enter the call and all that. Any ideas?

Thanks,
Jed

Greetings all.
I am looking to see if anyone else has run into this situation for field day, and if so, would love to hear from them.

Winter Field Day software networked via IP (wireless).
Each client also running the N7YG digital Engine to run PSK31.

We setup each laptop in the network and got them working as expected.
When you clicked on a station in the N7YG digital engine, the mouse pop up / break out box would list: station call, station section, station class.  
You pick the right one, and the information is carried over to the Field Day logging software.
Works slick.

Then we networked all of the machines.
From that point, ONLY the server machine (also used as a client) would work properly with the N7YG engine.
The server could run the N7YG software, and when clicking on a call sign would just have the three options come up (callsign, section, class) that would match with the Field Day software.   However, every other computer on the network defaulted to the standard selection that the N7YG software offers when used with the standard AClog.  A user clicks on a call sign,  and a popup with (name, grid, class, 1010 number, state, county.. etc etc..) would appear.  Class and Section are not options on this list, only 1 option (call sign) would carry over to the Field Day logging software. 

Again.  Turn off the networking to the server, restart field day logging software and the N7YG digital engine, and it works fine (3 options).  Shut down the software, turn the networking back on in the Field Day logging software.. restart n7YG digital engine.. back to the list of 10 or so options.

Has anyone else seen this and if so, what is the work around?  We had a mix of Win 7 and 10 machines and everything else worked great with the FD software.. just the interaction of the N7YG software on the networked clients was problematic.   I have also emailed Jeff directly to see if he has insight.

Thanks all, I hope FD went well for everyone.

- Jay N1RWY

Hey guys,

OK a question. It looks like i have configured the winkeyer in
amateur contact log. So what window should i be in when i want it to
transmit?
I'm in the main window right now where i can tab through the fields to
enter the call and all that. Any ideas?

Thanks,
Jed

Scott,

Was wondering if you could explain why in the statistics file generated
by the Field Day program that is shows below under AK as 2 when we did
not work Alaska and I cannot find AK in the program. Also if you look
above the UT there is an entry that has nothing but says we had 4 contacts?

Any Ideas?


Thanks for your support.

Larry  N8CWU

Total Contacts by State \ Prov:

State Total %
----- ----- ---
FL 64 6
OH 64 6
NC 56 6
PA 56 6
GA 55 5
TX 54 5
NY 51 5
VA 45 4
TN 39 4
IL 38 4
MI 38 4
ON 34 3
AL 30 3
MA 30 3
NJ 27 3
SC 27 3
MO 21 2
WI 18 2
IN 17 2
KY 17 2
MD 16 2
MS 16 2
IA 15 1
CA 14 1
NH 13 1
LA 11 1
AR 10 1
OK 10 1
QC 10 1
RI 10 1
CT 9 1
ME 9 1
NE 9 1
VT 7 1
AZ 6 1
KS 6 1
MN 6 1
WV 6 1
CO 5 0
OR 5 0
SD 5 0
4 0 <-----------
UT 4 0
WA 4 0
AK 2 0 <----------
DE 2 0
ID 2 0
NM 2 0
NV 2 0
BC 1 0
NT 1 0

Total = 50