Date   

rtty contest

george.wheatley
 

I was using n3fjp and n7yg digital engine this weekend in the rtty contest. digital engine would not pickup the next serial number, after a contact. if I went to the  logging drop down in digital engine,and went out & back in to n3fjp it would pickup the next number. help? 


Ray AE6XC



Re: ACL Error Message Problem using LoTw

calbroadalbin@...
 

Hi Scott,
 I finally tripped over the problem and as Pogo in comics once stated...."I have met the enemy and he is me!".  Regrettably, these old eyes failed to note an extra space in the Station Location this whole time.  Works just fine now!  Ugh!

Best regards,

Chuck NN2L


Re: Bearing: incorrect Miles: incorrect Cont: ok

Scott Davis
 

Hi Gary,

Thanks for your e-mail.  This FAQ will very likely get you going:


http://www.n3fjp.com/faq.html#q21

Enjoy!

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: stratton.gary@... [N3FJP_Software_Users]
To: N3FJP_Software_Users
Sent: Mon, Feb 12, 2018 12:32 pm
Subject: [N3FJP_Software_Users] Bearing: incorrect Miles: incorrect Cont: ok

 
Hi to all the AClog users,

This will be my first post on the group.
For some unknown reason (thus the post)

Bearing:  incorrect    Miles: incorrect  Cont: ok

CallBook is set to AC Log  Calldata (Free)

73,
Gary
KC2YTD


Bearing: incorrect Miles: incorrect Cont: ok

KC2YTD
 

Hi to all the AClog users,

This will be my first post on the group.
For some unknown reason (thus the post)

Bearing:  incorrect    Miles: incorrect  Cont: ok

CallBook is set to AC Log  Calldata (Free)

73,
Gary
KC2YTD



Re: unable to connect via snkdavis@aol.com

August Heins
 

OOPS, found it. 

Erwin Heins
aerwinh@...


On Sunday, February 11, 2018, 5:15:24 PM EST, Erwin Heins aerwinh@... [N3FJP_Software_Users] wrote:


 

Thanks to all of you that managed to find the cure to the problem.  Unfortunately, I still don't have an answer to my question. My balance is?

Erwin Heins  KM4QE
aerwinh@...


On Saturday, February 10, 2018, 5:05:13 PM EST, k2dfc@... [N3FJP_Software_Users] wrote:


 

I got an e-mail from Erwin today but trying to reply resulted in bounced mail. I found out his reply address had an error. A spelling error. it was "AERWNIH" instead of "AERWINH". Found the proper address on his QRZ page. Hope this helps.

Fred K2DFC



---In N3FJP_Software_Users@..., wrote :

Hi aerwinh,

Kimberly has attempted to e-mail you from both our snkdavis & affirmatechinc e-mail addresses.  Both result in this reply:


Capture.JPG



Do you have another e-mail address that we can try?  If so, please e-mail us direct from that address.

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users]
To: N3FJP_Software_Users
Sent: Fri, Feb 9, 2018 7:08 pm
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi aerwinh,

Thanks for your e-mail.  I'm sorry you've run into trouble.  We've been receiving lots of e-mail, so I'm sure the address is fine.  Please try writing us at:  affirmatechinc@...

Thanks in advance!

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: aerwinh@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: N3FJP_Software_Users <N3FJP_Software_Users@...>
Sent: Fri, Feb 9, 2018 6:26 pm
Subject: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi Scott and Kimberly, I have tried to send a message to you using the subject address but I don't seem to be getting through. I want to upgrade to the package and need my balance. My email address is aerwinh@.... Please pardon using the forum for this purpose but I couldn't think of a better way.


Re: unable to connect via snkdavis@aol.com

August Heins
 

Thanks to all of you that managed to find the cure to the problem.  Unfortunately, I still don't have an answer to my question. My balance is?

Erwin Heins  KM4QE
aerwinh@...


On Saturday, February 10, 2018, 5:05:13 PM EST, k2dfc@... [N3FJP_Software_Users] wrote:


 

I got an e-mail from Erwin today but trying to reply resulted in bounced mail. I found out his reply address had an error. A spelling error. it was "AERWNIH" instead of "AERWINH". Found the proper address on his QRZ page. Hope this helps.

Fred K2DFC



---In N3FJP_Software_Users@..., wrote :

Hi aerwinh,

Kimberly has attempted to e-mail you from both our snkdavis & affirmatechinc e-mail addresses.  Both result in this reply:


Capture.JPG



Do you have another e-mail address that we can try?  If so, please e-mail us direct from that address.

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users]
To: N3FJP_Software_Users
Sent: Fri, Feb 9, 2018 7:08 pm
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi aerwinh,

Thanks for your e-mail.  I'm sorry you've run into trouble.  We've been receiving lots of e-mail, so I'm sure the address is fine.  Please try writing us at:  affirmatechinc@...

Thanks in advance!

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: aerwinh@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: N3FJP_Software_Users <N3FJP_Software_Users@...>
Sent: Fri, Feb 9, 2018 6:26 pm
Subject: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi Scott and Kimberly, I have tried to send a message to you using the subject address but I don't seem to be getting through. I want to upgrade to the package and need my balance. My email address is aerwinh@.... Please pardon using the forum for this purpose but I couldn't think of a better way.


Re: Problem sending CW from N3FJP Loggers

Jeff Freedman <jeff.freedman@...>
 

Agreed totally. It takes about five minutes of playing with the three settings. Mine sounds natural.

Jeff Freedman K7JF
Gig Harbor, Washington


Re: Problem sending CW from N3FJP Loggers

Rick Davis
 

The cable linked below from Amazon has worked well on My Icom radios.  I suspect it should work on others as well

https://www.amazon.com/gp/product/B011KF4W20/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

Rick,  K8DOC


Re: import from N1MM

Greg P
 

thank you 


Re: import from N1MM

Scott Davis
 

Hi Greg,

Thanks for your e-mail.  With a callbook data source enabled, click Edit > Fill Fields Determined by Call.

Enjoy!


73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: wvcaver@... [N3FJP_Software_Users]
To: N3FJP_Software_Users
Sent: Sat, Feb 10, 2018 12:08 pm
Subject: [N3FJP_Software_Users] import from N1MM

 
when I import my log from a contest will missing info be filled in like state , name ect ?

thanks Greg W8OTR


Re: unable to connect via snkdavis@aol.com

Fred
 

I got an e-mail from Erwin today but trying to reply resulted in bounced mail. I found out his reply address had an error. A spelling error. it was "AERWNIH" instead of "AERWINH". Found the proper address on his QRZ page. Hope this helps.

Fred K2DFC


---In N3FJP_Software_Users@..., <SNKDavis@...> wrote :

Hi aerwinh,

Kimberly has attempted to e-mail you from both our snkdavis & affirmatechinc e-mail addresses.  Both result in this reply:





Do you have another e-mail address that we can try?  If so, please e-mail us direct from that address.

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: N3FJP_Software_Users <N3FJP_Software_Users@...>
Sent: Fri, Feb 9, 2018 7:08 pm
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi aerwinh,

Thanks for your e-mail.  I'm sorry you've run into trouble.  We've been receiving lots of e-mail, so I'm sure the address is fine.  Please try writing us at:  affirmatechinc@...

Thanks in advance!

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: aerwinh@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: N3FJP_Software_Users <N3FJP_Software_Users@...>
Sent: Fri, Feb 9, 2018 6:26 pm
Subject: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi Scott and Kimberly, I have tried to send a message to you using the subject address but I don't seem to be getting through. I want to upgrade to the package and need my balance. My email address is aerwinh@.... Please pardon using the forum for this purpose but I couldn't think of a better way.


Re: unable to connect via snkdavis@aol.com

Scott Davis
 

Hi Jeff,

Actually, no, this is the reverse.  We are doing fine on Yahoogroups, but unable to communicate direct.


73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: 'John H. Huber' n8fyl@... [N3FJP_Software_Users]
To: N3FJP_Software_Users
Sent: Sat, Feb 10, 2018 1:07 pm
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
I hope this has been resolved as I see a transposition in the address.  aerwinh is not aerwnih , eh?
We’ve all been there and done that typo thing, I’m sure.
 
73,  John / N8FYL
 
From: Jeff Steinkamp n7yg@... [N3FJP_Software_Users]
Sent: Saturday, February 10, 2018 11:09
To: N3FJP_Software_Users@...
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...
 
 
Scott
This is an internal problem with Yahoo.  Ever since Verizon bought out Yahoo, there has been serious issues with not only email begin delivered, but with the Yahoo groups.  We have had issues with Yahoo for about a year over at 10-10.  Their spam filters are set so tight that it's reject just about everything, including email that is generate on their own domain!!  If you send email that is in text only format, no HTML in the email, it will usually go through.
Jeff K. Steinkamp (N7YG)
Tucson, AZ
Scud Missile Coordinates
N32.2319 W110.8477
On 2/10/2018 04:40, Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users] wrote:
 
Hi aerwinh,

Kimberly has attempted to e-mail you from both our snkdavis & affirmatechinc e-mail addresses.  Both result in this reply:





Do you have another e-mail address that we can try?  If so, please e-mail us direct from that address.

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users] mailto:N3FJP_Software_Users@...
To: N3FJP_Software_Users mailto:N3FJP_Software_Users@...
Sent: Fri, Feb 9, 2018 7:08 pm
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi aerwinh,

Thanks for your e-mail.  I'm sorry you've run into trouble.  We've been receiving lots of e-mail, so I'm sure the address is fine.  Please try writing us at:  affirmatechinc@...
 
Thanks in advance!

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: aerwinh@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: N3FJP_Software_Users <N3FJP_Software_Users@...>
Sent: Fri, Feb 9, 2018 6:26 pm
Subject: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi Scott and Kimberly, I have tried to send a message to you using the subject address but I don't seem to be getting through. I want to upgrade to the package and need my balance. My email address is aerwinh@.... Please pardon using the forum for this purpose but I couldn't think of a better way.


Re: unable to connect via snkdavis@aol.com

John Huber
 

I hope this has been resolved as I see a transposition in the address.  aerwinh is not aerwnih , eh?
We’ve all been there and done that typo thing, I’m sure.
 
73,  John / N8FYL
 

From: Jeff Steinkamp n7yg@... [N3FJP_Software_Users]
Sent: Saturday, February 10, 2018 11:09
To: N3FJP_Software_Users@...
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...
 
 

Scott

This is an internal problem with Yahoo.  Ever since Verizon bought out Yahoo, there has been serious issues with not only email begin delivered, but with the Yahoo groups.  We have had issues with Yahoo for about a year over at 10-10.  Their spam filters are set so tight that it's reject just about everything, including email that is generate on their own domain!!  If you send email that is in text only format, no HTML in the email, it will usually go through.

Jeff K. Steinkamp (N7YG)
Tucson, AZ
Scud Missile Coordinates
N32.2319 W110.8477
On 2/10/2018 04:40, Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users] wrote:
 

Hi aerwinh,

Kimberly has attempted to e-mail you from both our snkdavis & affirmatechinc e-mail addresses.  Both result in this reply:





Do you have another e-mail address that we can try?  If so, please e-mail us direct from that address.

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users] mailto:N3FJP_Software_Users@...
To: N3FJP_Software_Users mailto:N3FJP_Software_Users@...
Sent: Fri, Feb 9, 2018 7:08 pm
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi aerwinh,

Thanks for your e-mail.  I'm sorry you've run into trouble.  We've been receiving lots of e-mail, so I'm sure the address is fine.  Please try writing us at:  affirmatechinc@...
 
Thanks in advance!

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: aerwinh@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: N3FJP_Software_Users <N3FJP_Software_Users@...>
Sent: Fri, Feb 9, 2018 6:26 pm
Subject: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi Scott and Kimberly, I have tried to send a message to you using the subject address but I don't seem to be getting through. I want to upgrade to the package and need my balance. My email address is aerwinh@.... Please pardon using the forum for this purpose but I couldn't think of a better way.


import from N1MM

Greg P
 

when I import my log from a contest will missing info be filled in like state , name ect ?


thanks Greg W8OTR


Re: unable to connect via snkdavis@aol.com

Jeff Steinkamp
 

Scott

This is an internal problem with Yahoo.  Ever since Verizon bought out Yahoo, there has been serious issues with not only email begin delivered, but with the Yahoo groups.  We have had issues with Yahoo for about a year over at 10-10.  Their spam filters are set so tight that it's reject just about everything, including email that is generate on their own domain!!  If you send email that is in text only format, no HTML in the email, it will usually go through.

Jeff K. Steinkamp (N7YG)
Tucson, AZ
Scud Missile Coordinates
N32.2319 W110.8477
On 2/10/2018 04:40, Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users] wrote:

 

Hi aerwinh,

Kimberly has attempted to e-mail you from both our snkdavis & affirmatechinc e-mail addresses.  Both result in this reply:





Do you have another e-mail address that we can try?  If so, please e-mail us direct from that address.

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users]
To: N3FJP_Software_Users
Sent: Fri, Feb 9, 2018 7:08 pm
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi aerwinh,

Thanks for your e-mail.  I'm sorry you've run into trouble.  We've been receiving lots of e-mail, so I'm sure the address is fine.  Please try writing us at:  affirmatechinc@...

Thanks in advance!

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: aerwinh@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: N3FJP_Software_Users <N3FJP_Software_Users@...>
Sent: Fri, Feb 9, 2018 6:26 pm
Subject: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi Scott and Kimberly, I have tried to send a message to you using the subject address but I don't seem to be getting through. I want to upgrade to the package and need my balance. My email address is aerwinh@.... Please pardon using the forum for this purpose but I couldn't think of a better way.


Re: Problem sending CW from N3FJP Loggers

Frank <maclamb@...>
 

Agreed

 

Frank

NG1I

 

From: N3FJP_Software_Users@... [mailto:N3FJP_Software_Users@...]
Sent: Friday, February 9, 2018 10:35 PM
To: N3FJP_Software_Users@...
Subject: Re: [N3FJP_Software_Users] Problem sending CW from N3FJP Loggers

 

 

I could never get decent sounding CW UNTIL I bought Winkeyer.  I recommend you do the same.

73,

Chris  NU1O
nu1oscar@...




-----Original Message-----
From: s9ss160m@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: N3FJP_Software_Users <N3FJP_Software_Users@...>
Sent: Fri, Feb 9, 2018 9:28 pm
Subject: [N3FJP_Software_Users] Problem sending CW from N3FJP Loggers

 

I don't have WINKEY and hope someone can help me get better results sending CW without it.  Most of the time my only problem is that I cannot get the logger to send code as fast I need.  Usually, the speed will not increase beyond what sounds to me like about 18 WPM.  Other times the speed jumps around erratically.  That makes it sound "choppy."  These things happen even when no other programs are running

The computer is a Dell Optiflex 3010 running WINDOWS 10.  It has plenty of free memory.

I am using the serial port adapter shown in the N3FJP instructions.

De KY4P - Charles

 


Re: PSKExpress and N7YG Digital Engine Updates

K8TS
 

Good Deal—got an excuse to play radio all day then.

Dale K8TS

 

Sent from Mail for Windows 10

 

From: Dan Morris dbmorris315@... [N3FJP_Software_Users]
Sent: Friday, February 9, 2018 11:13 PM
To: N3FJP_Software_Users@...
Subject: Re: [N3FJP_Software_Users] PSKExpress and N7YG Digital Engine Updates

 

 

Get well Jeff. I had cataract surgery back in Nov and 3 days later I got a viral infection in that eye. That was no fun at all. It took them a week to figure it out so a month and a half later it finally got better! 

Dan Morris


On Feb 9, 2018, at 10:36 PM, Jeff Steinkamp n7yg@... [N3FJP_Software_Users] <N3FJP_Software_Users@...> wrote:

 

I had the flu shot a few months ago.  This is not the flu but a viral infection in my throat.  So I'm sequestered into my house for a few days!!

Jeff K. Steinkamp (N7YG)
Tucson, AZ
Scud Missile Coordinates
N32.2319 W110.8477

On 2/9/2018 07:41, Dale dalecole3502@... [N3FJP_Software_Users] wrote:

 

Get a shot Jeff!  That crap is KILLING people.  I think we have had 3 here in Michigan, mostly youth. 

Dale K8TS

 

 

Sent from Mail for Windows 10

 

From: Jeff Steinkamp n7yg@... [N3FJP_Software_Users]
Sent: Friday, February 9, 2018 12:02 AM
To: RTTY DigitalEngine; N3FJP Software Users Group N3FJP Software Users Group
Subject: [N3FJP_Software_Users] PSKExpress and N7YG Digital Engine Updates

 

 

This evening I have released updates to both PSKExpress and N7YG Digital Engine. Hopefully, the FSK logic is corrected so it will work with all interfaces, home-brew or commercial. I was awaiting the receipt of a SDR dongle so I could do some monitoring on this end, but it now looks like it will be a couple of weeks before it gets here. So, I am doing something I haven’t done in the past and releasing this without my final testing. But since we do have the WPX RTTY contest approaching tomorrow evening, I though I’d get this out there and see if the FSK logic is truly fixed.

I have also added an option for Callsign Readback from the N3FJP API. This will be useful for those that are using search and pounce from the cluster. If you enable this option in the N3FJP setup, then anything that is typed into the call sign box in the N3FJP log will echo back to either program so it is available for your macros.

I have added a Cursor Marker that can optionally be displayed in the waterfall at a frequency of you choice. This will be beneficial for those that are operating FSK so you know where the transmit Mark or Space frequency is.

FSK is now a separate mode in the mode selection box. Selecting FSK will set all of the programs parameters to setup up FSK keying back to the radio via your interface. Please make sure you understand how FSK keying is developed in your radio and how to set it up in your commercial interface unit if it supports FSK keying.

I am off work Friday and Saturday if there is something I need to address in a hurry, but keep in mind, I am also a bit under the weather with what appears to be a cold or the flu coming on.

-- 
Jeff K. Steinkamp (N7YG)
Tucson, AZ
Scud Missile Coordinates
N32.2319 W110.8477

 

 

 


Re: unable to connect via snkdavis@aol.com

Scott Davis
 

Hi aerwinh,

Kimberly has attempted to e-mail you from both our snkdavis & affirmatechinc e-mail addresses.  Both result in this reply:





Do you have another e-mail address that we can try?  If so, please e-mail us direct from that address.

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: Scott & Kimberly Davis SNKDavis@... [N3FJP_Software_Users]
To: N3FJP_Software_Users
Sent: Fri, Feb 9, 2018 7:08 pm
Subject: Re: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi aerwinh,

Thanks for your e-mail.  I'm sorry you've run into trouble.  We've been receiving lots of e-mail, so I'm sure the address is fine.  Please try writing us at:  affirmatechinc@...

Thanks in advance!

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: aerwinh@... [N3FJP_Software_Users] <N3FJP_Software_Users@...>
To: N3FJP_Software_Users <N3FJP_Software_Users@...>
Sent: Fri, Feb 9, 2018 6:26 pm
Subject: [N3FJP_Software_Users] unable to connect via snkdavis@...

 
Hi Scott and Kimberly, I have tried to send a message to you using the subject address but I don't seem to be getting through. I want to upgrade to the package and need my balance. My email address is aerwinh@.... Please pardon using the forum for this purpose but I couldn't think of a better way.


Re: New user experance

Scott Davis
 

Hi Bill,

Thanks so much for your kind words and encouragement!

Enjoy!


73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: verstelle@... [N3FJP_Software_Users]
To: N3FJP_Software_Users
Sent: Fri, Feb 9, 2018 9:04 pm
Subject: [N3FJP_Software_Users] New user experance

 
Hello Scott and group,  well I have been using the logging software for a week or 2 now and have to say I love it. I have moved my contacts from misc other logging programs all into AClog and have got everything working so far. My eQSL and Lotw work great now up and down plus I have automatic logging working with WSJT-X using JT alert.  Right now I'm setting up Fldigi so fingers crossed all goes well there too. I also have it set up and working on laptop and used it on last RV trip then just exporting it to main computer when I get home. 
Thanks Brian and all who have contributed to this excellent program plus thanks to those who answered my newbe questions.
vy 73,
Bill N7OQ 


Re: Problem sending CW from N3FJP Loggers

Scott Davis
 

Hi Charles,

Thanks for your e-mail.  I'm sorry that you've run into trouble.

From the Timing Options at the top of the CW set up form, experiment with all three. They each take a different approach to processor timing and you'll likely find one more consistent on your PC than another.

For the most precise timing, do not run any other programs, virus software etc., while transmitting.

I've had good reports from lots of folks on processor timed CW and it is working great here with my FTDI, USB to serial adapter, but on some systems, the timing is either erratic or can not attain higher speeds.  It appears that some USB to serial adapters are producing slow or inconsistent timing with Windows .NET framework, while other USB to serial adapter / driver combinations are working fine.  If your processor generated CW is not satisfactory, Winkeyer is a great solution.

73, Scott
N3FJP
 
Serving the Amateur Radio community with contesting and general logging software since 1997.
 
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...
 
 


-----Original Message-----
From: s9ss160m@... [N3FJP_Software_Users]
To: N3FJP_Software_Users
Sent: Fri, Feb 9, 2018 9:28 pm
Subject: [N3FJP_Software_Users] Problem sending CW from N3FJP Loggers

 
I don't have WINKEY and hope someone can help me get better results sending CW without it.  Most of the time my only problem is that I cannot get the logger to send code as fast I need.  Usually, the speed will not increase beyond what sounds to me like about 18 WPM.  Other times the speed jumps around erratically.  That makes it sound "choppy."  These things happen even when no other programs are running

The computer is a Dell Optiflex 3010 running WINDOWS 10.  It has plenty of free memory.

I am using the serial port adapter shown in the N3FJP instructions.

De KY4P - Charles

16101 - 16120 of 49881