Date   

Re: RTTY with MMTTY & EXTFSK for FSK Keying

Tom Z <kg3vtomz@...>
 

Mike,

The instructions are long, but there are very good instructions in the N1MM+ documentation for setting up RTTY with MMTTY. I would back up and walk throguh that, at least the parts that talk about EXTFSK. Either you are not specifying the path correctlt and the requirement that N1MM+ uses MMTTY for this radio, or the .dll is not present in the path it is using. Could check your N1MM+ DI Window setup and make sure you are telling N1MM+ that it must use EXTFSK for that Radio in that specific DI Window.

Here is where I found the most help on N1MM+ using MMTTY:
Tom, KG3V


On Sat, Jan 2, 2016 at 10:06 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Tom

That is correct.  It isn't running.  The question is how to get it to run?

 It runs in MMTTY standalone, but not in the N1MM+ configuration.  

BTW, I am now using a separate directory for MMTTY for N1MM and pointing to that one.

For what it is worth, this is a RigExpert TI5 and it uses TxD at the control line.

Mike va3mw


On Sat, Jan 2, 2016 at 10:04 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

I may have had the name wrong (maybe a .dll), but you are closing in on it. I know I must see that EXTFSK Window or mine does not modulate. Also need to have the MMTTY settings specify that you are keying from that Port (Port=EXTFSK). But first things first - if it isn't running you will never get it to work.

73,

Tom, KG3V


On Sat, Jan 2, 2016 at 9:59 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Tom

It is clearly not running correctly and maybe using DTR instead of TxD.  The program is in the mmtty directory and that directory is the one specified in the configuration tab.

Thanks!

mike va3mw

On Sat, Jan 2, 2016 at 9:57 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Sounds like EXTFSK is not running. Do you have a copy of the EXTFSK.exe in the MMTTY directory that you are specifying in N1MM+ for the DI Window? Maybe that path is different than the one you use stand-alone?

Tom, KG3V

On Sat, Jan 2, 2016 at 9:53 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Tom

I radio and no, I do not get the EXTFSK setup screen, although I saw it once in MMVARI.  I do know what it looks like and I was looking for it.  In MMVARI it did say 'Status OK'.  

I did look at the extfsk.ini file and it 'seems' to be correct.  My Rigexpert TI-5 use TxD for the keying data.

This is only 1 radio.

It is strange that MMTTY works standalone, but the same copy fails with N1MM+.  

I will find it ... eventually.

73, mike va3mw


On Sat, Jan 2, 2016 at 9:30 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

When you fire everything up, do you get the separate EXTFSK Window displayed? and does it say STATUS:OK? The problem is that you are not getting your digital data to the FSK modulator. Could be due to settings in N1MM+ or EXTFSK. Are you using two radios? If so, can you disable the other one and see if that changes anything?

I just fought a similar problem the other day. I posted all my screenshots on my Blog (KG3V.COM), in case that helps.

73 and GL,

Tom, KG3V


On Sat, Jan 2, 2016 at 7:57 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Thanks and I was concerned about that.

I have spent a few hours on it looking for exactly that.

I did check the extfsk.ini file and it has the right port for TxD.  If I send a message from N1MM+, I do see it in the DI-1 Window, the radio does go into TX, but only with a single tone.

Checking the MMTTY setup, it does have EXTFSK setup correctly and it is exactly the same for both standalone and N1MM.

Question for the developers:

N1MM+ and the DI interface send the TX data into MMTTY and then MMTTY handles the communication with EXTFSK and from there it goes to TxD on the FSK Com port and finally the radio?

It isn't a permissions issue as this is Win XP 32 Bit and has worked in the past.  

I do get an error message from RE2EXTFSK.ini and the PTT port conflict, but reading the docs, I feel it is safe to ignore that.

I don't exactly have to use MMTTY, but I do want to use FSK and not AFSK.  What other options might I have?

Mike va3mw


On Sat, Jan 2, 2016 at 5:21 AM, Oliver Dröse droese@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

make double sure you have the MMTTY settings within NL+ exactly the same as when running standalone. AFAIK MMTTY is using different config files when run alone and in NL+ (even if you start the same EXE in standalone mode). That's a typical pitfall ...

73 & gl, Olli - DH8BQA

Contest, DX & radio projects: http://www.dh8bqa.de


Am 02.01.2016 um 04:23 schrieb Michael Walker va3mw@... [N1MMLoggerplus]:
 
Good evening all and HNY

I have this strange problem with a TS480 in FSK mode (not AFSK) and N1MM+.  I used to have this working  N1MM original.  I am usually pretty good with RTTY and FSK, so I understand how each input plays with the hardware.

I am using MMTTY and it works fine in standalone, and in FSK mode (32Bit XP) with EXTFSK. 

However running N1MM with the DI visable, the radio goes into transmit, but no FSK happens. 

This means that PTT is commanded (by hardware, not software) and EXTFSK is not shifting the FSK line.

I read the docs (2 or 4 times now) and I don't think I missed anything, but ...

  • I have the paths to MMTTY set up in the configurator and the path to MMTTY set correctly.
  • I have NOT specified the FSK com port in N1MM (as specified in the docs)
  • The MMTTY settings are correct (again, it works standalone)
  • I am running the same copy of MMTTY standalone as I do in N1MM+
I am sure I have missed something, but I am not sure what and I am curious if anyone else has tripped over the same problem and remembers how they solved it.

Thanks in advance, Mike va3mw

p.s.  Rich (KI), I copied you on 80 CQing and I would have answered if I could of :).  I also couldn't figure out which contest this was as I couldn't find it in the calendar.






--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!





--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!





--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!





--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!


Re: RTTY with MMTTY & EXTFSK for FSK Keying

Michael Walker
 

Tom

That is correct.  It isn't running.  The question is how to get it to run?

 It runs in MMTTY standalone, but not in the N1MM+ configuration.  

BTW, I am now using a separate directory for MMTTY for N1MM and pointing to that one.

For what it is worth, this is a RigExpert TI5 and it uses TxD at the control line.

Mike va3mw


On Sat, Jan 2, 2016 at 10:04 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

I may have had the name wrong (maybe a .dll), but you are closing in on it. I know I must see that EXTFSK Window or mine does not modulate. Also need to have the MMTTY settings specify that you are keying from that Port (Port=EXTFSK). But first things first - if it isn't running you will never get it to work.

73,

Tom, KG3V


On Sat, Jan 2, 2016 at 9:59 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Tom

It is clearly not running correctly and maybe using DTR instead of TxD.  The program is in the mmtty directory and that directory is the one specified in the configuration tab.

Thanks!

mike va3mw

On Sat, Jan 2, 2016 at 9:57 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Sounds like EXTFSK is not running. Do you have a copy of the EXTFSK.exe in the MMTTY directory that you are specifying in N1MM+ for the DI Window? Maybe that path is different than the one you use stand-alone?

Tom, KG3V

On Sat, Jan 2, 2016 at 9:53 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Tom

I radio and no, I do not get the EXTFSK setup screen, although I saw it once in MMVARI.  I do know what it looks like and I was looking for it.  In MMVARI it did say 'Status OK'.  

I did look at the extfsk.ini file and it 'seems' to be correct.  My Rigexpert TI-5 use TxD for the keying data.

This is only 1 radio.

It is strange that MMTTY works standalone, but the same copy fails with N1MM+.  

I will find it ... eventually.

73, mike va3mw


On Sat, Jan 2, 2016 at 9:30 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

When you fire everything up, do you get the separate EXTFSK Window displayed? and does it say STATUS:OK? The problem is that you are not getting your digital data to the FSK modulator. Could be due to settings in N1MM+ or EXTFSK. Are you using two radios? If so, can you disable the other one and see if that changes anything?

I just fought a similar problem the other day. I posted all my screenshots on my Blog (KG3V.COM), in case that helps.

73 and GL,

Tom, KG3V


On Sat, Jan 2, 2016 at 7:57 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Thanks and I was concerned about that.

I have spent a few hours on it looking for exactly that.

I did check the extfsk.ini file and it has the right port for TxD.  If I send a message from N1MM+, I do see it in the DI-1 Window, the radio does go into TX, but only with a single tone.

Checking the MMTTY setup, it does have EXTFSK setup correctly and it is exactly the same for both standalone and N1MM.

Question for the developers:

N1MM+ and the DI interface send the TX data into MMTTY and then MMTTY handles the communication with EXTFSK and from there it goes to TxD on the FSK Com port and finally the radio?

It isn't a permissions issue as this is Win XP 32 Bit and has worked in the past.  

I do get an error message from RE2EXTFSK.ini and the PTT port conflict, but reading the docs, I feel it is safe to ignore that.

I don't exactly have to use MMTTY, but I do want to use FSK and not AFSK.  What other options might I have?

Mike va3mw


On Sat, Jan 2, 2016 at 5:21 AM, Oliver Dröse droese@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

make double sure you have the MMTTY settings within NL+ exactly the same as when running standalone. AFAIK MMTTY is using different config files when run alone and in NL+ (even if you start the same EXE in standalone mode). That's a typical pitfall ...

73 & gl, Olli - DH8BQA

Contest, DX & radio projects: http://www.dh8bqa.de


Am 02.01.2016 um 04:23 schrieb Michael Walker va3mw@... [N1MMLoggerplus]:
 
Good evening all and HNY

I have this strange problem with a TS480 in FSK mode (not AFSK) and N1MM+.  I used to have this working  N1MM original.  I am usually pretty good with RTTY and FSK, so I understand how each input plays with the hardware.

I am using MMTTY and it works fine in standalone, and in FSK mode (32Bit XP) with EXTFSK. 

However running N1MM with the DI visable, the radio goes into transmit, but no FSK happens. 

This means that PTT is commanded (by hardware, not software) and EXTFSK is not shifting the FSK line.

I read the docs (2 or 4 times now) and I don't think I missed anything, but ...

  • I have the paths to MMTTY set up in the configurator and the path to MMTTY set correctly.
  • I have NOT specified the FSK com port in N1MM (as specified in the docs)
  • The MMTTY settings are correct (again, it works standalone)
  • I am running the same copy of MMTTY standalone as I do in N1MM+
I am sure I have missed something, but I am not sure what and I am curious if anyone else has tripped over the same problem and remembers how they solved it.

Thanks in advance, Mike va3mw

p.s.  Rich (KI), I copied you on 80 CQing and I would have answered if I could of :).  I also couldn't figure out which contest this was as I couldn't find it in the calendar.






--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!





--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!





--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!



Re: RTTY with MMTTY & EXTFSK for FSK Keying

Tom Z <kg3vtomz@...>
 

I may have had the name wrong (maybe a .dll), but you are closing in on it. I know I must see that EXTFSK Window or mine does not modulate. Also need to have the MMTTY settings specify that you are keying from that Port (Port=EXTFSK). But first things first - if it isn't running you will never get it to work.

73,

Tom, KG3V


On Sat, Jan 2, 2016 at 9:59 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Tom

It is clearly not running correctly and maybe using DTR instead of TxD.  The program is in the mmtty directory and that directory is the one specified in the configuration tab.

Thanks!

mike va3mw

On Sat, Jan 2, 2016 at 9:57 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Sounds like EXTFSK is not running. Do you have a copy of the EXTFSK.exe in the MMTTY directory that you are specifying in N1MM+ for the DI Window? Maybe that path is different than the one you use stand-alone?

Tom, KG3V

On Sat, Jan 2, 2016 at 9:53 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Tom

I radio and no, I do not get the EXTFSK setup screen, although I saw it once in MMVARI.  I do know what it looks like and I was looking for it.  In MMVARI it did say 'Status OK'.  

I did look at the extfsk.ini file and it 'seems' to be correct.  My Rigexpert TI-5 use TxD for the keying data.

This is only 1 radio.

It is strange that MMTTY works standalone, but the same copy fails with N1MM+.  

I will find it ... eventually.

73, mike va3mw


On Sat, Jan 2, 2016 at 9:30 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

When you fire everything up, do you get the separate EXTFSK Window displayed? and does it say STATUS:OK? The problem is that you are not getting your digital data to the FSK modulator. Could be due to settings in N1MM+ or EXTFSK. Are you using two radios? If so, can you disable the other one and see if that changes anything?

I just fought a similar problem the other day. I posted all my screenshots on my Blog (KG3V.COM), in case that helps.

73 and GL,

Tom, KG3V


On Sat, Jan 2, 2016 at 7:57 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Thanks and I was concerned about that.

I have spent a few hours on it looking for exactly that.

I did check the extfsk.ini file and it has the right port for TxD.  If I send a message from N1MM+, I do see it in the DI-1 Window, the radio does go into TX, but only with a single tone.

Checking the MMTTY setup, it does have EXTFSK setup correctly and it is exactly the same for both standalone and N1MM.

Question for the developers:

N1MM+ and the DI interface send the TX data into MMTTY and then MMTTY handles the communication with EXTFSK and from there it goes to TxD on the FSK Com port and finally the radio?

It isn't a permissions issue as this is Win XP 32 Bit and has worked in the past.  

I do get an error message from RE2EXTFSK.ini and the PTT port conflict, but reading the docs, I feel it is safe to ignore that.

I don't exactly have to use MMTTY, but I do want to use FSK and not AFSK.  What other options might I have?

Mike va3mw


On Sat, Jan 2, 2016 at 5:21 AM, Oliver Dröse droese@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

make double sure you have the MMTTY settings within NL+ exactly the same as when running standalone. AFAIK MMTTY is using different config files when run alone and in NL+ (even if you start the same EXE in standalone mode). That's a typical pitfall ...

73 & gl, Olli - DH8BQA

Contest, DX & radio projects: http://www.dh8bqa.de


Am 02.01.2016 um 04:23 schrieb Michael Walker va3mw@... [N1MMLoggerplus]:
 
Good evening all and HNY

I have this strange problem with a TS480 in FSK mode (not AFSK) and N1MM+.  I used to have this working  N1MM original.  I am usually pretty good with RTTY and FSK, so I understand how each input plays with the hardware.

I am using MMTTY and it works fine in standalone, and in FSK mode (32Bit XP) with EXTFSK. 

However running N1MM with the DI visable, the radio goes into transmit, but no FSK happens. 

This means that PTT is commanded (by hardware, not software) and EXTFSK is not shifting the FSK line.

I read the docs (2 or 4 times now) and I don't think I missed anything, but ...

  • I have the paths to MMTTY set up in the configurator and the path to MMTTY set correctly.
  • I have NOT specified the FSK com port in N1MM (as specified in the docs)
  • The MMTTY settings are correct (again, it works standalone)
  • I am running the same copy of MMTTY standalone as I do in N1MM+
I am sure I have missed something, but I am not sure what and I am curious if anyone else has tripped over the same problem and remembers how they solved it.

Thanks in advance, Mike va3mw

p.s.  Rich (KI), I copied you on 80 CQing and I would have answered if I could of :).  I also couldn't figure out which contest this was as I couldn't find it in the calendar.






--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!





--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!





--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!


Re: RTTY with MMTTY & EXTFSK for FSK Keying

Michael Walker
 

Tom

It is clearly not running correctly and maybe using DTR instead of TxD.  The program is in the mmtty directory and that directory is the one specified in the configuration tab.

Thanks!

mike va3mw

On Sat, Jan 2, 2016 at 9:57 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Sounds like EXTFSK is not running. Do you have a copy of the EXTFSK.exe in the MMTTY directory that you are specifying in N1MM+ for the DI Window? Maybe that path is different than the one you use stand-alone?

Tom, KG3V

On Sat, Jan 2, 2016 at 9:53 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Tom

I radio and no, I do not get the EXTFSK setup screen, although I saw it once in MMVARI.  I do know what it looks like and I was looking for it.  In MMVARI it did say 'Status OK'.  

I did look at the extfsk.ini file and it 'seems' to be correct.  My Rigexpert TI-5 use TxD for the keying data.

This is only 1 radio.

It is strange that MMTTY works standalone, but the same copy fails with N1MM+.  

I will find it ... eventually.

73, mike va3mw


On Sat, Jan 2, 2016 at 9:30 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

When you fire everything up, do you get the separate EXTFSK Window displayed? and does it say STATUS:OK? The problem is that you are not getting your digital data to the FSK modulator. Could be due to settings in N1MM+ or EXTFSK. Are you using two radios? If so, can you disable the other one and see if that changes anything?

I just fought a similar problem the other day. I posted all my screenshots on my Blog (KG3V.COM), in case that helps.

73 and GL,

Tom, KG3V


On Sat, Jan 2, 2016 at 7:57 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Thanks and I was concerned about that.

I have spent a few hours on it looking for exactly that.

I did check the extfsk.ini file and it has the right port for TxD.  If I send a message from N1MM+, I do see it in the DI-1 Window, the radio does go into TX, but only with a single tone.

Checking the MMTTY setup, it does have EXTFSK setup correctly and it is exactly the same for both standalone and N1MM.

Question for the developers:

N1MM+ and the DI interface send the TX data into MMTTY and then MMTTY handles the communication with EXTFSK and from there it goes to TxD on the FSK Com port and finally the radio?

It isn't a permissions issue as this is Win XP 32 Bit and has worked in the past.  

I do get an error message from RE2EXTFSK.ini and the PTT port conflict, but reading the docs, I feel it is safe to ignore that.

I don't exactly have to use MMTTY, but I do want to use FSK and not AFSK.  What other options might I have?

Mike va3mw


On Sat, Jan 2, 2016 at 5:21 AM, Oliver Dröse droese@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

make double sure you have the MMTTY settings within NL+ exactly the same as when running standalone. AFAIK MMTTY is using different config files when run alone and in NL+ (even if you start the same EXE in standalone mode). That's a typical pitfall ...

73 & gl, Olli - DH8BQA

Contest, DX & radio projects: http://www.dh8bqa.de


Am 02.01.2016 um 04:23 schrieb Michael Walker va3mw@... [N1MMLoggerplus]:
 
Good evening all and HNY

I have this strange problem with a TS480 in FSK mode (not AFSK) and N1MM+.  I used to have this working  N1MM original.  I am usually pretty good with RTTY and FSK, so I understand how each input plays with the hardware.

I am using MMTTY and it works fine in standalone, and in FSK mode (32Bit XP) with EXTFSK. 

However running N1MM with the DI visable, the radio goes into transmit, but no FSK happens. 

This means that PTT is commanded (by hardware, not software) and EXTFSK is not shifting the FSK line.

I read the docs (2 or 4 times now) and I don't think I missed anything, but ...

  • I have the paths to MMTTY set up in the configurator and the path to MMTTY set correctly.
  • I have NOT specified the FSK com port in N1MM (as specified in the docs)
  • The MMTTY settings are correct (again, it works standalone)
  • I am running the same copy of MMTTY standalone as I do in N1MM+
I am sure I have missed something, but I am not sure what and I am curious if anyone else has tripped over the same problem and remembers how they solved it.

Thanks in advance, Mike va3mw

p.s.  Rich (KI), I copied you on 80 CQing and I would have answered if I could of :).  I also couldn't figure out which contest this was as I couldn't find it in the calendar.






--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!





--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!



Re: RTTY with MMTTY & EXTFSK for FSK Keying

Tom Z <kg3vtomz@...>
 

Sounds like EXTFSK is not running. Do you have a copy of the EXTFSK.exe in the MMTTY directory that you are specifying in N1MM+ for the DI Window? Maybe that path is different than the one you use stand-alone?

Tom, KG3V

On Sat, Jan 2, 2016 at 9:53 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Tom

I radio and no, I do not get the EXTFSK setup screen, although I saw it once in MMVARI.  I do know what it looks like and I was looking for it.  In MMVARI it did say 'Status OK'.  

I did look at the extfsk.ini file and it 'seems' to be correct.  My Rigexpert TI-5 use TxD for the keying data.

This is only 1 radio.

It is strange that MMTTY works standalone, but the same copy fails with N1MM+.  

I will find it ... eventually.

73, mike va3mw


On Sat, Jan 2, 2016 at 9:30 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

When you fire everything up, do you get the separate EXTFSK Window displayed? and does it say STATUS:OK? The problem is that you are not getting your digital data to the FSK modulator. Could be due to settings in N1MM+ or EXTFSK. Are you using two radios? If so, can you disable the other one and see if that changes anything?

I just fought a similar problem the other day. I posted all my screenshots on my Blog (KG3V.COM), in case that helps.

73 and GL,

Tom, KG3V


On Sat, Jan 2, 2016 at 7:57 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Thanks and I was concerned about that.

I have spent a few hours on it looking for exactly that.

I did check the extfsk.ini file and it has the right port for TxD.  If I send a message from N1MM+, I do see it in the DI-1 Window, the radio does go into TX, but only with a single tone.

Checking the MMTTY setup, it does have EXTFSK setup correctly and it is exactly the same for both standalone and N1MM.

Question for the developers:

N1MM+ and the DI interface send the TX data into MMTTY and then MMTTY handles the communication with EXTFSK and from there it goes to TxD on the FSK Com port and finally the radio?

It isn't a permissions issue as this is Win XP 32 Bit and has worked in the past.  

I do get an error message from RE2EXTFSK.ini and the PTT port conflict, but reading the docs, I feel it is safe to ignore that.

I don't exactly have to use MMTTY, but I do want to use FSK and not AFSK.  What other options might I have?

Mike va3mw


On Sat, Jan 2, 2016 at 5:21 AM, Oliver Dröse droese@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

make double sure you have the MMTTY settings within NL+ exactly the same as when running standalone. AFAIK MMTTY is using different config files when run alone and in NL+ (even if you start the same EXE in standalone mode). That's a typical pitfall ...

73 & gl, Olli - DH8BQA

Contest, DX & radio projects: http://www.dh8bqa.de


Am 02.01.2016 um 04:23 schrieb Michael Walker va3mw@... [N1MMLoggerplus]:
 
Good evening all and HNY

I have this strange problem with a TS480 in FSK mode (not AFSK) and N1MM+.  I used to have this working  N1MM original.  I am usually pretty good with RTTY and FSK, so I understand how each input plays with the hardware.

I am using MMTTY and it works fine in standalone, and in FSK mode (32Bit XP) with EXTFSK. 

However running N1MM with the DI visable, the radio goes into transmit, but no FSK happens. 

This means that PTT is commanded (by hardware, not software) and EXTFSK is not shifting the FSK line.

I read the docs (2 or 4 times now) and I don't think I missed anything, but ...

  • I have the paths to MMTTY set up in the configurator and the path to MMTTY set correctly.
  • I have NOT specified the FSK com port in N1MM (as specified in the docs)
  • The MMTTY settings are correct (again, it works standalone)
  • I am running the same copy of MMTTY standalone as I do in N1MM+
I am sure I have missed something, but I am not sure what and I am curious if anyone else has tripped over the same problem and remembers how they solved it.

Thanks in advance, Mike va3mw

p.s.  Rich (KI), I copied you on 80 CQing and I would have answered if I could of :).  I also couldn't figure out which contest this was as I couldn't find it in the calendar.






--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!





--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!


Re: RTTY with MMTTY & EXTFSK for FSK Keying

Michael Walker
 

Tom

I radio and no, I do not get the EXTFSK setup screen, although I saw it once in MMVARI.  I do know what it looks like and I was looking for it.  In MMVARI it did say 'Status OK'.  

I did look at the extfsk.ini file and it 'seems' to be correct.  My Rigexpert TI-5 use TxD for the keying data.

This is only 1 radio.

It is strange that MMTTY works standalone, but the same copy fails with N1MM+.  

I will find it ... eventually.

73, mike va3mw


On Sat, Jan 2, 2016 at 9:30 AM, Tom Z kg3vtomz@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

When you fire everything up, do you get the separate EXTFSK Window displayed? and does it say STATUS:OK? The problem is that you are not getting your digital data to the FSK modulator. Could be due to settings in N1MM+ or EXTFSK. Are you using two radios? If so, can you disable the other one and see if that changes anything?

I just fought a similar problem the other day. I posted all my screenshots on my Blog (KG3V.COM), in case that helps.

73 and GL,

Tom, KG3V


On Sat, Jan 2, 2016 at 7:57 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Thanks and I was concerned about that.

I have spent a few hours on it looking for exactly that.

I did check the extfsk.ini file and it has the right port for TxD.  If I send a message from N1MM+, I do see it in the DI-1 Window, the radio does go into TX, but only with a single tone.

Checking the MMTTY setup, it does have EXTFSK setup correctly and it is exactly the same for both standalone and N1MM.

Question for the developers:

N1MM+ and the DI interface send the TX data into MMTTY and then MMTTY handles the communication with EXTFSK and from there it goes to TxD on the FSK Com port and finally the radio?

It isn't a permissions issue as this is Win XP 32 Bit and has worked in the past.  

I do get an error message from RE2EXTFSK.ini and the PTT port conflict, but reading the docs, I feel it is safe to ignore that.

I don't exactly have to use MMTTY, but I do want to use FSK and not AFSK.  What other options might I have?

Mike va3mw


On Sat, Jan 2, 2016 at 5:21 AM, Oliver Dröse droese@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

make double sure you have the MMTTY settings within NL+ exactly the same as when running standalone. AFAIK MMTTY is using different config files when run alone and in NL+ (even if you start the same EXE in standalone mode). That's a typical pitfall ...

73 & gl, Olli - DH8BQA

Contest, DX & radio projects: http://www.dh8bqa.de


Am 02.01.2016 um 04:23 schrieb Michael Walker va3mw@... [N1MMLoggerplus]:
 
Good evening all and HNY

I have this strange problem with a TS480 in FSK mode (not AFSK) and N1MM+.  I used to have this working  N1MM original.  I am usually pretty good with RTTY and FSK, so I understand how each input plays with the hardware.

I am using MMTTY and it works fine in standalone, and in FSK mode (32Bit XP) with EXTFSK. 

However running N1MM with the DI visable, the radio goes into transmit, but no FSK happens. 

This means that PTT is commanded (by hardware, not software) and EXTFSK is not shifting the FSK line.

I read the docs (2 or 4 times now) and I don't think I missed anything, but ...

  • I have the paths to MMTTY set up in the configurator and the path to MMTTY set correctly.
  • I have NOT specified the FSK com port in N1MM (as specified in the docs)
  • The MMTTY settings are correct (again, it works standalone)
  • I am running the same copy of MMTTY standalone as I do in N1MM+
I am sure I have missed something, but I am not sure what and I am curious if anyone else has tripped over the same problem and remembers how they solved it.

Thanks in advance, Mike va3mw

p.s.  Rich (KI), I copied you on 80 CQing and I would have answered if I could of :).  I also couldn't figure out which contest this was as I couldn't find it in the calendar.






--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!



Re: Call Stacking Has Changed

Jamie WW3S
 

my experience has been, you HAVE to follow the format EXACTLY......even though F5 is the equivalent of ! I could never get it to work when substituting ! for F5 or populating it with the exchange instead of F2......Larry K8UT has some excellent videos on the website and is the master of log popping.....
 

> On 1/2/2016 8:56:18 AM, Rick Ellison rellison@... [N1MMLoggerplus] (N1MMLoggerplus@...) wrote:
> > Nothing has changed in CallStacking.. As far as I have known it has always been {F5} + {F2}
>

>
> 73 Rick N2AMG
>

>
> From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
> Sent: Friday, January 1, 2016 10:23 PM
> To: N1MMLogger-Digital@...; [N1MMLoggerplus]
> Cc: k8ut@...
> Subject: [N1MMLoggerplus] Call Stacking Has Changed
>

>
>  
>
> During the RTTY roundup testing this evening, my log them pop macro seems to have quit.
>

>
> I have:
>

>
> F12 NOW, {TX}{enter}! {LOGTHENPOP} TU NOW ! {F2} {RX}
>

>

>
> If I change it to:
>
> F12 NOW, {TX}{enter}! {LOGTHENPOP} TU NOW {f5} {F2} {RX}
>
> It works fine. BUT, I get the CR and line feed that Larry K8UT says you can eliminate by using the first macro.
>

>
> Has something changed in the software or do I have something not right in my setup?
>

>
> Thanks
>
> 73
>
> Jim W7RY
>

>
>
>
>
>
>
> -----
> No virus found in this message.
> Checked by


Re: RTTY with MMTTY & EXTFSK for FSK Keying

Tom Z <kg3vtomz@...>
 

Mike,

When you fire everything up, do you get the separate EXTFSK Window displayed? and does it say STATUS:OK? The problem is that you are not getting your digital data to the FSK modulator. Could be due to settings in N1MM+ or EXTFSK. Are you using two radios? If so, can you disable the other one and see if that changes anything?

I just fought a similar problem the other day. I posted all my screenshots on my Blog (KG3V.COM), in case that helps.

73 and GL,

Tom, KG3V


On Sat, Jan 2, 2016 at 7:57 AM, Michael Walker va3mw@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Thanks and I was concerned about that.

I have spent a few hours on it looking for exactly that.

I did check the extfsk.ini file and it has the right port for TxD.  If I send a message from N1MM+, I do see it in the DI-1 Window, the radio does go into TX, but only with a single tone.

Checking the MMTTY setup, it does have EXTFSK setup correctly and it is exactly the same for both standalone and N1MM.

Question for the developers:

N1MM+ and the DI interface send the TX data into MMTTY and then MMTTY handles the communication with EXTFSK and from there it goes to TxD on the FSK Com port and finally the radio?

It isn't a permissions issue as this is Win XP 32 Bit and has worked in the past.  

I do get an error message from RE2EXTFSK.ini and the PTT port conflict, but reading the docs, I feel it is safe to ignore that.

I don't exactly have to use MMTTY, but I do want to use FSK and not AFSK.  What other options might I have?

Mike va3mw


On Sat, Jan 2, 2016 at 5:21 AM, Oliver Dröse droese@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

make double sure you have the MMTTY settings within NL+ exactly the same as when running standalone. AFAIK MMTTY is using different config files when run alone and in NL+ (even if you start the same EXE in standalone mode). That's a typical pitfall ...

73 & gl, Olli - DH8BQA

Contest, DX & radio projects: http://www.dh8bqa.de


Am 02.01.2016 um 04:23 schrieb Michael Walker va3mw@... [N1MMLoggerplus]:
 
Good evening all and HNY

I have this strange problem with a TS480 in FSK mode (not AFSK) and N1MM+.  I used to have this working  N1MM original.  I am usually pretty good with RTTY and FSK, so I understand how each input plays with the hardware.

I am using MMTTY and it works fine in standalone, and in FSK mode (32Bit XP) with EXTFSK. 

However running N1MM with the DI visable, the radio goes into transmit, but no FSK happens. 

This means that PTT is commanded (by hardware, not software) and EXTFSK is not shifting the FSK line.

I read the docs (2 or 4 times now) and I don't think I missed anything, but ...

  • I have the paths to MMTTY set up in the configurator and the path to MMTTY set correctly.
  • I have NOT specified the FSK com port in N1MM (as specified in the docs)
  • The MMTTY settings are correct (again, it works standalone)
  • I am running the same copy of MMTTY standalone as I do in N1MM+
I am sure I have missed something, but I am not sure what and I am curious if anyone else has tripped over the same problem and remembers how they solved it.

Thanks in advance, Mike va3mw

p.s.  Rich (KI), I copied you on 80 CQing and I would have answered if I could of :).  I also couldn't figure out which contest this was as I couldn't find it in the calendar.






--
-----------------------------------------------------
The Ham Bands are priceless and you earned the right to use them
Get on the Air - Use them or Lose them!


Re: Call Stacking Has Changed

Rick Ellison
 

Nothing has changed in CallStacking.. As far as I have known it has always been {F5} + {F2}

 

73 Rick N2AMG

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Friday, January 1, 2016 10:23 PM
To: N1MMLogger-Digital@...; [N1MMLoggerplus]
Cc: k8ut@...
Subject: [N1MMLoggerplus] Call Stacking Has Changed

 

 

During the RTTY roundup testing this evening, my log them pop macro seems to have quit. 

 

I have:

 

F12 NOW, {TX}{enter}! {LOGTHENPOP} TU NOW ! {F2} {RX}

 

 

If I change it to:

F12 NOW, {TX}{enter}! {LOGTHENPOP} TU NOW {f5} {F2} {RX}

It works fine. BUT, I get the CR and line feed that Larry K8UT says you can eliminate by using the first macro.

 

Has something changed in the software or do I have something not right in my setup?

 

Thanks

73

Jim W7RY

 


Re: Admin.db defrag?

Goetz DJ3IW
 

Thanks again!

 

73 de Goetz DJ3IW

 

Von: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Gesendet: Samstag, 2. Januar 2016 13:26
An: N1MMLoggerplus@...
Betreff: RE: [N1MMLoggerplus] Admin.db defrag?

 

 

 

Goetz,

 

This started in July and is a byproduct of the change below. No you can not change it.

 

John, K3CT

 

Program Start: Load the Goal and Call History associated files on every program start. (N2IC)(Coded by K3CT)

 

 

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Saturday, January 02, 2016 5:29 AM
To: N1MM+
Subject: [N1MMLoggerplus] Admin.db defrag?

 

 

Hi and a happy New Year to all.

I'm running Version 1.0.5403 setup for RTTY Roundup in a new 2016.s3db. "Use
call history file" is active and the latest Master.scp was installed
yesterday. The only log in this new database is the SARTG HNY.
Now each time N1MM+ is started a window with "Admin.db defrag please wait"
comes up before the actual program windows. Have not seen this before. Any
clue why this is happening and how to get rid of it?

73 de Goetz DJ3IW


Re: Call History File

gbyahoo@...
 

Jamie,

Both csv and txt files are just plain text files and can be combined and edited with a normal text editor. You might also recall that you can import multiple CHF's to combine information.

>> Gerald, VE1DT



---In N1MMLoggerplus@..., <ww3s@...> wrote :

speaking of call history, trying to add a csv file to an existing txt file, and thought I did it before using MEdit from VE3NEA website but having trouble tonight.....
 



Re: Call History File

gbyahoo@...
 

Hank,

I can confirm that I am seeing the same issue you are with this contest. I tried another contest (cwops) and it does work like one would expect in that it does bring up the new info (name in this case) instead of the CHF data for the same callsign on a new band.

I have not used the RTTY Roundup contest before, so I don't know if this worked previously as you and I would expect.

>> Gerald, VE1DT



---In N1MMLoggerplus@..., <w6sx@...> wrote :

Just finished RTTY Roundup practice. Using Call History File which populates state as expected.

I worked two fellows with state different from Call History File, so entered the new state and logged the contacts.

When I worked the same two fellows on different band, state was populated with CHF state, not the new state I entered when I worked them on first band.

I would expect and hope that new state would be shown. I think it used to work that way.

Am I doing something wrong?

Contest Exuberantly,

Hank, W6SX



Re: Admin.db defrag?

John Bednar
 

 

Goetz,

 

This started in July and is a byproduct of the change below. No you can not change it.

 

John, K3CT

 

Program Start: Load the Goal and Call History associated files on every program start. (N2IC)(Coded by K3CT)

 

 

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Saturday, January 02, 2016 5:29 AM
To: N1MM+
Subject: [N1MMLoggerplus] Admin.db defrag?

 

 

Hi and a happy New Year to all.

I'm running Version 1.0.5403 setup for RTTY Roundup in a new 2016.s3db. "Use
call history file" is active and the latest Master.scp was installed
yesterday. The only log in this new database is the SARTG HNY.
Now each time N1MM+ is started a window with "Admin.db defrag please wait"
comes up before the actual program windows. Have not seen this before. Any
clue why this is happening and how to get rid of it?

73 de Goetz DJ3IW


Re: RTTY with MMTTY & EXTFSK for FSK Keying

Michael Walker
 

Thanks and I was concerned about that.

I have spent a few hours on it looking for exactly that.

I did check the extfsk.ini file and it has the right port for TxD.  If I send a message from N1MM+, I do see it in the DI-1 Window, the radio does go into TX, but only with a single tone.

Checking the MMTTY setup, it does have EXTFSK setup correctly and it is exactly the same for both standalone and N1MM.

Question for the developers:

N1MM+ and the DI interface send the TX data into MMTTY and then MMTTY handles the communication with EXTFSK and from there it goes to TxD on the FSK Com port and finally the radio?

It isn't a permissions issue as this is Win XP 32 Bit and has worked in the past.  

I do get an error message from RE2EXTFSK.ini and the PTT port conflict, but reading the docs, I feel it is safe to ignore that.

I don't exactly have to use MMTTY, but I do want to use FSK and not AFSK.  What other options might I have?

Mike va3mw


On Sat, Jan 2, 2016 at 5:21 AM, Oliver Dröse droese@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mike,

make double sure you have the MMTTY settings within NL+ exactly the same as when running standalone. AFAIK MMTTY is using different config files when run alone and in NL+ (even if you start the same EXE in standalone mode). That's a typical pitfall ...

73 & gl, Olli - DH8BQA

Contest, DX & radio projects: http://www.dh8bqa.de


Am 02.01.2016 um 04:23 schrieb Michael Walker va3mw@... [N1MMLoggerplus]:
 
Good evening all and HNY

I have this strange problem with a TS480 in FSK mode (not AFSK) and N1MM+.  I used to have this working  N1MM original.  I am usually pretty good with RTTY and FSK, so I understand how each input plays with the hardware.

I am using MMTTY and it works fine in standalone, and in FSK mode (32Bit XP) with EXTFSK. 

However running N1MM with the DI visable, the radio goes into transmit, but no FSK happens. 

This means that PTT is commanded (by hardware, not software) and EXTFSK is not shifting the FSK line.

I read the docs (2 or 4 times now) and I don't think I missed anything, but ...

  • I have the paths to MMTTY set up in the configurator and the path to MMTTY set correctly.
  • I have NOT specified the FSK com port in N1MM (as specified in the docs)
  • The MMTTY settings are correct (again, it works standalone)
  • I am running the same copy of MMTTY standalone as I do in N1MM+
I am sure I have missed something, but I am not sure what and I am curious if anyone else has tripped over the same problem and remembers how they solved it.

Thanks in advance, Mike va3mw

p.s.  Rich (KI), I copied you on 80 CQing and I would have answered if I could of :).  I also couldn't figure out which contest this was as I couldn't find it in the calendar.




Re: Admin.db defrag?

Goetz DJ3IW
 

Thank you Boštjan!

 

73 de Goetz DJ3IW

 

Von: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Gesendet: Samstag, 2. Januar 2016 11:16
An: N1MMLoggerplus@...
Betreff: Re: [N1MMLoggerplus] Admin.db defrag?

 

 

It's normal when you use call history file. Just usualy it's so short you dont see it at all. Just neglect.

Cheers any HNY

Boštjan Ian S55O

 

2016-01-02 11:29 GMT+01:00 'GL-DJ3IW-Web' gl-dj3iw@... [N1MMLoggerplus] <N1MMLoggerplus@...>:

 

Hi and a happy New Year to all.

I'm running Version 1.0.5403 setup for RTTY Roundup in a new 2016.s3db. "Use
call history file" is active and the latest Master.scp was installed
yesterday. The only log in this new database is the SARTG HNY.
Now each time N1MM+ is started a window with "Admin.db defrag please wait"
comes up before the actual program windows. Have not seen this before. Any
clue why this is happening and how to get rid of it?

73 de Goetz DJ3IW

 


Re: Admin.db defrag?

Bostjan Voncina
 

It's normal when you use call history file. Just usualy it's so short you dont see it at all. Just neglect.

Cheers any HNY
Boštjan Ian S55O

2016-01-02 11:29 GMT+01:00 'GL-DJ3IW-Web' gl-dj3iw@... [N1MMLoggerplus] <N1MMLoggerplus@...>:

 

Hi and a happy New Year to all.

I'm running Version 1.0.5403 setup for RTTY Roundup in a new 2016.s3db. "Use
call history file" is active and the latest Master.scp was installed
yesterday. The only log in this new database is the SARTG HNY.
Now each time N1MM+ is started a window with "Admin.db defrag please wait"
comes up before the actual program windows. Have not seen this before. Any
clue why this is happening and how to get rid of it?

73 de Goetz DJ3IW



Admin.db defrag?

Goetz DJ3IW
 

Hi and a happy New Year to all.

I'm running Version 1.0.5403 setup for RTTY Roundup in a new 2016.s3db. "Use
call history file" is active and the latest Master.scp was installed
yesterday. The only log in this new database is the SARTG HNY.
Now each time N1MM+ is started a window with "Admin.db defrag please wait"
comes up before the actual program windows. Have not seen this before. Any
clue why this is happening and how to get rid of it?

73 de Goetz DJ3IW


Re: RTTY with MMTTY & EXTFSK for FSK Keying

Olli
 

Mike,

make double sure you have the MMTTY settings within NL+ exactly the same as when running standalone. AFAIK MMTTY is using different config files when run alone and in NL+ (even if you start the same EXE in standalone mode). That's a typical pitfall ...

73 & gl, Olli - DH8BQA
Contest, DX & radio projects: http://www.dh8bqa.de


Am 02.01.2016 um 04:23 schrieb Michael Walker va3mw@... [N1MMLoggerplus]:

 
Good evening all and HNY

I have this strange problem with a TS480 in FSK mode (not AFSK) and N1MM+.  I used to have this working  N1MM original.  I am usually pretty good with RTTY and FSK, so I understand how each input plays with the hardware.

I am using MMTTY and it works fine in standalone, and in FSK mode (32Bit XP) with EXTFSK. 

However running N1MM with the DI visable, the radio goes into transmit, but no FSK happens. 

This means that PTT is commanded (by hardware, not software) and EXTFSK is not shifting the FSK line.

I read the docs (2 or 4 times now) and I don't think I missed anything, but ...

  • I have the paths to MMTTY set up in the configurator and the path to MMTTY set correctly.
  • I have NOT specified the FSK com port in N1MM (as specified in the docs)
  • The MMTTY settings are correct (again, it works standalone)
  • I am running the same copy of MMTTY standalone as I do in N1MM+
I am sure I have missed something, but I am not sure what and I am curious if anyone else has tripped over the same problem and remembers how they solved it.

Thanks in advance, Mike va3mw

p.s.  Rich (KI), I copied you on 80 CQing and I would have answered if I could of :).  I also couldn't figure out which contest this was as I couldn't find it in the calendar.



Re: RTTY - no diddles with FSK

Jim N7US
 

I forgot to mention that I’m using a resistor/transistor interface, as shown on AA5AU’s website, connected to an Edgeport adaptor.  I’m not using EXTFSK.

 

73, Jim N7US

 

 

From: Jim McDonald [mailto:jim@...]
Sent: January 01, 2016 22:22
To: 'N1MMLoggerplus@...'
Subject: RTTY - no diddles with FSK

 

I recently reconfigured my COM ports and wish I hadn’t.  With my K3, I can send FSK just fine with MMTTY standalone and with DXLab’s WinWarbler, but not with N1MM+.

 

With the current release of N1MM+ on a computer running Windows 10, with Cortana disabled, the PTT keys but I get a carrier but no diddles (mark or space).  The characters of the message memory are being generated according to the TX window.  Listening on the K3’s monitor, the tone has some flutter.

 

I do not have COM ports (SO2V) assigned to digital in the Hardware Configurer, as I do have them assigned in each instance of MMTTY.

 

I have reviewed the digital setup documentation.  Any suggestions would be appreciated.

 

73, Jim N7US

 

 


RTTY - no diddles with FSK

Jim N7US
 

I recently reconfigured my COM ports and wish I hadn’t.  With my K3, I can send FSK just fine with MMTTY standalone and with DXLab’s WinWarbler, but not with N1MM+.

 

With the current release of N1MM+ on a computer running Windows 10, with Cortana disabled, the PTT keys but I get a carrier but no diddles (mark or space).  The characters of the message memory are being generated according to the TX window.  Listening on the K3’s monitor, the tone has some flutter.

 

I do not have COM ports (SO2V) assigned to digital in the Hardware Configurer, as I do have them assigned in each instance of MMTTY.

 

I have reviewed the digital setup documentation.  Any suggestions would be appreciated.

 

73, Jim N7US