Date   
Re: Problem with DI in WAE

Rick I2BRT
 

It's strange. A lot more difficult of what I remember last year...
I too had some issue.
One is : the Yellow bar is engaged (means "pause the rx screen) but seems to be triggered more often than desired. I must click again on the Yellow bar to revert to green.
73

Re: Automatically sending leading zero

Larry K8UT
 

Yes. Under >Configure >Function Keys, "Send leading zeroes in serial numbers"


------ Original Message ------
From: "John, G4DRS via Groups.Io" <g4drs@...>
Sent: 2019-11-09 18:46:27
Subject: [N1MM+] Automatically sending leading zero

Is there a setting that makes serial numbers below 100 send as '0xx' rather than 'xx'?
I recently re-installed N1MM+, and I seem to have lost some of my setup.


Cheers,


John
G4DRS

Re: Grayline Nighttime terminator very light

Tom Wagner (N1MM)
 

Download https://n1mmwp.hamdocs.com/mmfiles/worldlores-png/

and place it in the N1MM SupportFiles directory.  Replace any file with the same name in tha directory.

Tom

On 11/9/2019 4:51 PM, Karin Johnson wrote:
Using version 1.0.7977.0 the Grayline night time terminator shadow is almost invisible.
I saw some previous comments about this about a year ago has something broken with Grayline code????

Karin

Automatically sending leading zero

John, G4DRS
 

Is there a setting that makes serial numbers below 100 send as '0xx' rather than 'xx'?
I recently re-installed N1MM+, and I seem to have lost some of my setup.


Cheers,


John
G4DRS

Re: RSGB 1.8MHz AFS (Club Calls)

John, G4DRS
 

I'm not sure if it's me,but I don't understand why the module auto-populates the club for a station that has been worked on another mode, but not the status (C,H or N).
Is it a feature,or an enhancement request?


John
G4DRS

Grayline Nighttime terminator very light

Karin Johnson
 

Using version 1.0.7977.0 the Grayline night time terminator shadow is almost invisible.
I saw some previous comments about this about a year ago has something broken with Grayline code????

Karin

Re: Problem with DI in WAE

VE2FK
 

Bill I just tested when receiving QTC and I could not get
the QTC header without freezing even clicking end of the line.
Had to switch to RX window 2.
But maybe for the 10 QTC it help, will try
73
 
 

Sent: Saturday, November 09, 2019 3:47 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 
The screen is a bit demanding with the clicks. Being in W7, I don't get a lot of practice RXing QTC's
but it seems critical that the mouse click is on the very last digit of each line, for 1610-DP7W-033, you
have to click exactly on the 3 as it goes scrolling by :)

73, Bill

Garanti sans virus. www.avg.com

Re: Problem with DI in WAE

VE2FK
 

OK, will give it a try about the QTC header too.
73 GL
 

Sent: Saturday, November 09, 2019 3:47 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 
The screen is a bit demanding with the clicks. Being in W7, I don't get a lot of practice RXing QTC's
but it seems critical that the mouse click is on the very last digit of each line, for 1610-DP7W-033, you
have to click exactly on the 3 as it goes scrolling by :)

73, Bill
 

Re: Problem with DI in WAE

Bill KO7SS
 

The screen is a bit demanding with the clicks. Being in W7, I don't get a lot of practice RXing QTC's 
but it seems critical that the mouse click is on the very last digit of each line, for 1610-DP7W-033, you
have to click exactly on the 3 as it goes scrolling by :)

73, Bill

Re: Problem with DI in WAE

VE2FK
 

Oh Boy... for some reason, because newest version are upset down
I was using very old version...  now I got it.
 
Will see if it help also for freeze
 
Thanks
Claude
 
 

From: ve3ki
Sent: Saturday, November 09, 2019 3:25 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 
There is a new option immediately below the Rt Click = Return NOT Menu, called With RtClicked enabled Don't drop On-Deck call. Is that the one you are looking for?

73,
Rich VE3KI



On Sat, Nov 9, 2019 at 03:19 PM, VE2FK wrote:
Not there anymore ha ha!  or I am blind.
 
Sent: Saturday, November 09, 2019 3:10 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 

DI Setup menu about half way down. Right click doesn’t drop call. Something like that..

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 2:01 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

Yes I am using scrolling window.

Dont worry Rick, we can still work.

Another thing, Right Click deck down dont work and

I can not find where is the command.

 

73 de VE2FK

 

 

From: Rick Ellison

Sent: Saturday, November 09, 2019 1:52 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

From: NS2N_PTA@...

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

 


On Sat, Nov 9, 2019 at 03:19 PM, VE2FK wrote:
Not there anymore ha ha!  or I am blind.
 
Sent: Saturday, November 09, 2019 3:10 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 

DI Setup menu about half way down. Right click doesn’t drop call. Something like that..

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 2:01 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

Yes I am using scrolling window.

Dont worry Rick, we can still work.

Another thing, Right Click deck down dont work and

I can not find where is the command.

 

73 de VE2FK

 

 

From: Rick Ellison

Sent: Saturday, November 09, 2019 1:52 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

From: NS2N_PTA@...

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

 

Re: Problem with DI in WAE

VE2FK
 

YES but I dont see it.
 
 

From: ve3ki
Sent: Saturday, November 09, 2019 3:25 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 
There is a new option immediately below the Rt Click = Return NOT Menu, called With RtClicked enabled Don't drop On-Deck call. Is that the one you are looking for?

73,
Rich VE3KI



On Sat, Nov 9, 2019 at 03:19 PM, VE2FK wrote:
Not there anymore ha ha!  or I am blind.
 
Sent: Saturday, November 09, 2019 3:10 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 

DI Setup menu about half way down. Right click doesn’t drop call. Something like that..

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 2:01 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

Yes I am using scrolling window.

Dont worry Rick, we can still work.

Another thing, Right Click deck down dont work and

I can not find where is the command.

 

73 de VE2FK

 

 

From: Rick Ellison

Sent: Saturday, November 09, 2019 1:52 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

From: NS2N_PTA@...

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

 


On Sat, Nov 9, 2019 at 03:19 PM, VE2FK wrote:
Not there anymore ha ha!  or I am blind.
 
Sent: Saturday, November 09, 2019 3:10 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 

DI Setup menu about half way down. Right click doesn’t drop call. Something like that..

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 2:01 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

Yes I am using scrolling window.

Dont worry Rick, we can still work.

Another thing, Right Click deck down dont work and

I can not find where is the command.

 

73 de VE2FK

 

 

From: Rick Ellison

Sent: Saturday, November 09, 2019 1:52 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

From: NS2N_PTA@...

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

 

Re: Problem with DI in WAE

ve3ki
 

There is a new option immediately below the Rt Click = Return NOT Menu, called With RtClicked enabled Don't drop On-Deck call. Is that the one you are looking for?

73,
Rich VE3KI



On Sat, Nov 9, 2019 at 03:19 PM, VE2FK wrote:
Not there anymore ha ha!  or I am blind.
 
Sent: Saturday, November 09, 2019 3:10 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 

DI Setup menu about half way down. Right click doesn’t drop call. Something like that..

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 2:01 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

Yes I am using scrolling window.

Dont worry Rick, we can still work.

Another thing, Right Click deck down dont work and

I can not find where is the command.

 

73 de VE2FK

 

 

From: Rick Ellison

Sent: Saturday, November 09, 2019 1:52 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

From: NS2N_PTA@...

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

 


 On Sat, Nov 9, 2019 at 03:19 PM, VE2FK wrote:
Not there anymore ha ha!  or I am blind.
 
Sent: Saturday, November 09, 2019 3:10 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 

DI Setup menu about half way down. Right click doesn’t drop call. Something like that..

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 2:01 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

Yes I am using scrolling window.

Dont worry Rick, we can still work.

Another thing, Right Click deck down dont work and

I can not find where is the command.

 

73 de VE2FK

 

 

From: Rick Ellison

Sent: Saturday, November 09, 2019 1:52 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

From: NS2N_PTA@...

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

 

Re: Problem with DI in WAE

VE2FK
 

Not there anymore ha ha!  or I am blind.
 

Sent: Saturday, November 09, 2019 3:10 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 

DI Setup menu about half way down. Right click doesn’t drop call. Something like that..

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 2:01 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

Yes I am using scrolling window.

Dont worry Rick, we can still work.

Another thing, Right Click deck down dont work and

I can not find where is the command.

 

73 de VE2FK

 

 

From: Rick Ellison

Sent: Saturday, November 09, 2019 1:52 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

From: NS2N_PTA@...

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

Re: Problem with DI in WAE

Rick Ellison
 

DI Setup menu about half way down. Right click doesn’t drop call. Something like that..

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 2:01 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

Yes I am using scrolling window.

Dont worry Rick, we can still work.

Another thing, Right Click deck down dont work and

I can not find where is the command.

 

73 de VE2FK

 

 

Sent: Saturday, November 09, 2019 1:52 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

Re: Problem with DI in WAE

VE2FK
 

Yes it is a second RX window and also MMTTY as the main window.
It works ok if I use it to receive QTC, no freeze. I also have a third one, 2Tone
but have not try it.  For now all is ok.
 
GL
 

Sent: Saturday, November 09, 2019 2:54 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 
Yes, I'm using the scroll and tried both.  When you say open a 2nd window is that a MMTTY window?  I already have GRITTY for crosschecking and
no space for a 3rd window.  I did have this problem last year but thought it was my computer so never posted and frankly had
forgotten about it.
Doug - N7NM

Garanti sans virus. www.avg.com

Re: Problem with DI in WAE

Doug Ferguson
 

Yes, I'm using the scroll and tried both.  When you say open a 2nd window is that a MMTTY window?  I already have GRITTY for crosschecking and
no space for a 3rd window.  I did have this problem last year but thought it was my computer so never posted and frankly had
forgotten about it. 
Doug - N7NM

Re: Problem with DI in WAE

VE2FK
 

Yes I am using scrolling window.
Dont worry Rick, we can still work.
Another thing, Right Click deck down dont work and
I can not find where is the command.
 
73 de VE2FK
 
 

Sent: Saturday, November 09, 2019 1:52 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

From: NS2N_PTA@...

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

Re: Problem with DI in WAE

Rick Ellison
 

Are you using the non-scrolling window?? If so try switching to the scrolling window. I’m not home to look at the source code but nothing in this section of the code ever changes but I do know if the scrolling window there is a statement that turns off the channel pause that gets turned on when clicking on a qtc.

 

73 Rick N2AMG

 

From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf Of VE2FK
Sent: Saturday, November 9, 2019 1:06 PM
To: N1MMLoggerPlus@groups.io
Subject: Re: [N1MM+] Problem with DI in WAE

 

If you have another RX window open try that one, it’s ok here on second RX window.

 

 

Sent: Saturday, November 09, 2019 1:01 PM

Subject: Re: [N1MM+] Problem with DI in WAE

 

Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE

 

I am having the same problem, Freezing when clicking on the QTC Header.

That is only in the mane DI window with MMTTY

I have another RX window also with MMTTY and no problem there.

 

Claude VE2FK

 

 

Sent: Saturday, November 09, 2019 12:26 PM

Subject: [N1MM+] Problem with DI in WAE

 

I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

 

Garanti sans virus. www.avg.com

Re: Problem with DI in WAE

NS2N_PTA@...
 

Only using standard window.
No extras

I can type it in but by the time that's done, I'm 3 or 4 qtcs behind, furiously clicking away!

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 1:05:38 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE
 
If you have another RX window open try that one, it’s ok here on second RX window.
 
 
Sent: Saturday, November 09, 2019 1:01 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 
Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE
 
I am having the same problem, Freezing when clicking on the QTC Header.
That is only in the mane DI window with MMTTY
I have another RX window also with MMTTY and no problem there.
 
Claude VE2FK
 
 
Sent: Saturday, November 09, 2019 12:26 PM
Subject: [N1MM+] Problem with DI in WAE
 
I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

Garanti sans virus. www.avg.com

Re: Problem with DI in WAE

VE2FK
 

If you have another RX window open try that one, it’s ok here on second RX window.
 
 

Sent: Saturday, November 09, 2019 1:01 PM
Subject: Re: [N1MM+] Problem with DI in WAE
 
Also same problem, and can' t click in QTC header - have to type manually .

NS2N


From: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io> on behalf of VE2FK <duberger.miousse81@...>
Sent: Saturday, November 9, 2019 12:54:09 PM
To: N1MMLoggerPlus@groups.io <N1MMLoggerPlus@groups.io>
Subject: Re: [N1MM+] Problem with DI in WAE
 
I am having the same problem, Freezing when clicking on the QTC Header.
That is only in the mane DI window with MMTTY
I have another RX window also with MMTTY and no problem there.
 
Claude VE2FK
 
 
Sent: Saturday, November 09, 2019 12:26 PM
Subject: [N1MM+] Problem with DI in WAE
 
I'm having a big issue with the DI freezing when receiving QTC's in the WAE.  Usually a few will print and I can
click to fill the QTC form but at some point the DI freezes up and the green side bar turns yellow.  I have not found
a way to unfreeze it by clicking on something.  It only frees up when I move off freq. but then I lose the sent QTC's.
If I manually go ahead and tell sender that I've received all ok I can go back and fill in from GRITTY DI but it's a huge hassle
especially if I'm running. 
Any thoughts would be apprecited
Doug - N7NM

Garanti sans virus. www.avg.com