Date   

Re: MMTTY integration to N1MM+

ve3ki@...
 

Just checking - is MMTTY already running stand-alone when you start up N1MM+? Make sure it isn't - opening the DI window in N1MM+ should open up MMTTY automatically. If MMTTY is running first, it will not communicate with N1MM+

Have you followed all of the instructions at <http://n1mmplus.hamdocs.com/tiki-index.php?page=Digital+Installation+and+Setup&structure=N1MM+Logger+Documentation#Setting_up_N1MM_Logger_for_Digital_Modes> ? or in more detail, at <http://n1mmplus.hamdocs.com/tiki-index.php?page=Digital+Setup#Setting_Up_the_Configurer> ? If you have configured the FSK port in the N1MM+ Configurer (this may be unnecessary, BTW), make sure you have set the DigWndNr to 1 (for DI1; 2 for DI2 in SO2R/SO2V).

On another tack, which version of Windows are you using? This is a shot in the dark, but my understanding is that in Windows 10, Cortana interferes with some inter-process communications. I do not recall hearing of this with N1MM+, but there is always a first time, and it has been reported to be a problem in DXLab Suite (see <http://www.dxlabsuite.com/dxlabwiki/Windows10Performance> ).

73,
Rich VE3KI


---In N1MMLoggerplus@..., <kzerohb@...> wrote :

I am trying to configure N1MM+, MMTTY, and microKEYER-II to run in this weekends CQWW RTTY contest.
 
Something is falling apart in the food chain.
 
When TXing from N1MM+ the transmitter keys up as expected, the message scrolls across the N1MM+/MMTTY screen, and the TX drops at the end of the scrolling message.  But instead of sending the message, the transmitted signal is just "diddles".  I am set up for pure FSK, not AFSK.
 
If I open MMTTY as a standalone app (outside N1MM+), I can send traffic normally.  Suggests that N1MM+ is not passing traffic to MMTTY, so I must have some option set incorrectly.
 
Any thoughts?
 
73, de Hans, K0HB
--
"Just a boy and his radio"™
--
Proud Member of:
. ARRL - http://www.arrl.org
. RSGB - http://www.rsgb.org
. A1 Operators - http://www.arrl.org/a-1-op
. Minnesota Wireless contesters - http://www.W0AA.org
. Arizona Outlaws contesters - http://www.arizonaoutlaws.net
. Twin City DX Assn - http://www.tcdxa.org
. Minnesota Amateur Radio Technical Society - http://www.mn-arts.org/
. Lake Vermilion DX Assn - http://www.lvdxa.org
. Royal Naval Amateur Radio Society - http://www.rnars.org.uk/
. SOC - http://www.qsl.net/soc
. CW Operators Club – http://www.cwops.org
. SKCC - http://www.skccgroup.com/
--


 


Re: MMTTY integration to N1MM+

Les Elliott
 

In the Digital Engine Window
click Option>Setup>Misc tab
have you got ‘Tx Port’ set to Sound?
 
Les, G4OGB
 

Sent: Friday, September 25, 2015 4:13 PM
Subject: [N1MMLoggerplus] MMTTY integration to N1MM+
 
 

I am trying to configure N1MM+, MMTTY, and microKEYER-II to run in this weekends CQWW RTTY contest.
 
Something is falling apart in the food chain.
 
When TXing from N1MM+ the transmitter keys up as expected, the message scrolls across the N1MM+/MMTTY screen, and the TX drops at the end of the scrolling message.  But instead of sending the message, the transmitted signal is just "diddles".  I am set up for pure FSK, not AFSK.
 
If I open MMTTY as a standalone app (outside N1MM+), I can send traffic normally.  Suggests that N1MM+ is not passing traffic to MMTTY, so I must have some option set incorrectly.
 
Any thoughts?
 
73, de Hans, K0HB
--
"Just a boy and his radio"™
--
Proud Member of:
. ARRL - http://www.arrl.org
. RSGB - http://www.rsgb.org
. A1 Operators - http://www.arrl.org/a-1-op
. Minnesota Wireless contesters - http://www.W0AA.org
. Arizona Outlaws contesters - http://www.arizonaoutlaws.net
. Twin City DX Assn - http://www.tcdxa.org
. Minnesota Amateur Radio Technical Society - http://www.mn-arts.org/
. Lake Vermilion DX Assn - http://www.lvdxa.org
. Royal Naval Amateur Radio Society - http://www.rnars.org.uk/
. SOC - http://www.qsl.net/soc
. CW Operators Club – http://www.cwops.org
. SKCC - http://www.skccgroup.com/
--



MMTTY integration to N1MM+

Hans Brakob
 

I am trying to configure N1MM+, MMTTY, and microKEYER-II to run in this weekends CQWW RTTY contest.
 
Something is falling apart in the food chain.
 
When TXing from N1MM+ the transmitter keys up as expected, the message scrolls across the N1MM+/MMTTY screen, and the TX drops at the end of the scrolling message.  But instead of sending the message, the transmitted signal is just "diddles".  I am set up for pure FSK, not AFSK.
 
If I open MMTTY as a standalone app (outside N1MM+), I can send traffic normally.  Suggests that N1MM+ is not passing traffic to MMTTY, so I must have some option set incorrectly.
 
Any thoughts?
 
73, de Hans, K0HB
--
"Just a boy and his radio"™
--
Proud Member of:
. ARRL - http://www.arrl.org
. RSGB - http://www.rsgb.org
. A1 Operators - http://www.arrl.org/a-1-op
. Minnesota Wireless contesters - http://www.W0AA.org
. Arizona Outlaws contesters - http://www.arizonaoutlaws.net
. Twin City DX Assn - http://www.tcdxa.org
. Minnesota Amateur Radio Technical Society - http://www.mn-arts.org/
. Lake Vermilion DX Assn - http://www.lvdxa.org
. Royal Naval Amateur Radio Society - http://www.rnars.org.uk/
. SOC - http://www.qsl.net/soc
. CW Operators Club – http://www.cwops.org
. SKCC - http://www.skccgroup.com/
--



Re: Score Reporting Server

lu9cbl@gmail.com <lu9cbl@...>
 

Thanks a lot

73s
Mat LU9CBL

El 25/09/2015 a las 09:52 a.m., 'John Bednar' k3ct@... [N1MMLoggerplus] escribió:
 

 

Mat,

 

Open Config, select the score reporting tab.

Change the text in the Score Reporting Server box.

 

John, K3CT

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Friday, September 25, 2015 7:55 AM
To: N1MMLoggerplus@...
Subject: Re: [N1MMLoggerplus] Score Reporting Server

 

 

Thanks John!!!

 

Do you know where i can found the way to modify it?

 

73s

Mat LU9CBL

 

On Fri, Sep 25, 2015 at 5:43 AM, 'John Bednar' k3ct@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:

 

Mat,

 

Yes, from the Release Notes for version 1.0.4998:

 

Allow user to enter any URL for the realtime score reporting server. (K6TU) (Coded by N2IC)

 

John, K3CT

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Thursday, September 24, 2015 5:49 PM
To: n1mmloggerplus@...
Subject: [N1MMLoggerplus] Score Reporting Server

 

 

Hi to All!!

 

Reading the help off N1MM plus, i saw this… “Score Reporting Server - At this time, the only real-time score reporting server is cqcontest.net. If any when others become available, they will be added.”

 

Is there any way to change this, for testing only and use a private Reporting Server??? I want to play with this option, but I can´t find where I can add my own server URL, and the messages that the program wait to run.

 

Thanks in advance

73s

Mat LU9CBL

 


El software de antivirus Avast ha analizado este correo electrónico en busca de virus.
www.avast.com

 

 



Re: Score Reporting Server

John Bednar
 

 

Mat,

 

Open Config, select the score reporting tab.

Change the text in the Score Reporting Server box.

 

John, K3CT

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Friday, September 25, 2015 7:55 AM
To: N1MMLoggerplus@...
Subject: Re: [N1MMLoggerplus] Score Reporting Server

 

 

Thanks John!!!

 

Do you know where i can found the way to modify it?

 

73s

Mat LU9CBL

 

On Fri, Sep 25, 2015 at 5:43 AM, 'John Bednar' k3ct@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:

 

Mat,

 

Yes, from the Release Notes for version 1.0.4998:

 

Allow user to enter any URL for the realtime score reporting server. (K6TU) (Coded by N2IC)

 

John, K3CT

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Thursday, September 24, 2015 5:49 PM
To: n1mmloggerplus@...
Subject: [N1MMLoggerplus] Score Reporting Server

 

 

Hi to All!!

 

Reading the help off N1MM plus, i saw this… “Score Reporting Server - At this time, the only real-time score reporting server is cqcontest.net. If any when others become available, they will be added.”

 

Is there any way to change this, for testing only and use a private Reporting Server??? I want to play with this option, but I can´t find where I can add my own server URL, and the messages that the program wait to run.

 

Thanks in advance

73s

Mat LU9CBL

 


El software de antivirus Avast ha analizado este correo electrónico en busca de virus.
www.avast.com

 

 


Re: Updating The Check Partial

gbyahoo@...
 

Anthony,

What type of error message is it throwing, eg) a popup or an error in one of the Windows? What is the wording of the message?

Are errors being added to the N1MM+ errorlog? You can access the errorlog in N1MM+ via the Help menu and clicking on the "View error log for debugging". If so, please copy and paste here.

Was this working previously and any estimate for when it stopped working?

>> Gerald, VE1DT


---In N1MMLoggerplus@..., <5d19a403@...> wrote :

Gerald,

Yes I am able to access it via my browser.  It seems to be isolate to Logger +.  I am able to update the CTY.dat file via Logger +.  It is just trying to update the check partial via logger + that it throws the error.  No firewall or internet blockages.

I downloaded it manually and updated it that way but be advised it throws an error when trying to update via Logger +.  Using latest version.

Anthony 


Re: Score Reporting Server

Matías Graiño <lu9cbl@...>
 

Thanks John!!!

Do you know where i can found the way to modify it?

73s
Mat LU9CBL

On Fri, Sep 25, 2015 at 5:43 AM, 'John Bednar' k3ct@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

Mat,

 

Yes, from the Release Notes for version 1.0.4998:

 

Allow user to enter any URL for the realtime score reporting server. (K6TU) (Coded by N2IC)

 

John, K3CT

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Thursday, September 24, 2015 5:49 PM
To: n1mmloggerplus@...
Subject: [N1MMLoggerplus] Score Reporting Server

 

 

Hi to All!!

 

Reading the help off N1MM plus, i saw this… “Score Reporting Server - At this time, the only real-time score reporting server is cqcontest.net. If any when others become available, they will be added.”

 

Is there any way to change this, for testing only and use a private Reporting Server??? I want to play with this option, but I can´t find where I can add my own server URL, and the messages that the program wait to run.

 

Thanks in advance

73s

Mat LU9CBL

 


El software de antivirus Avast ha analizado este correo electrónico en busca de virus.
www.avast.com

 



Re: Updating The Check Partial

Pete Smith N4ZR <n4zr@...>
 

The function worked fine for me in version 5221 (the latest public release.
73, Pete N4ZR
Download the new N1MM Logger+ at 
. Check 
out the Reverse Beacon Network at 
, now 
spotting RTTY activity worldwide. 
For spots, please use your favorite 
"retail" DX cluster.
On 9/25/2015 7:02 AM, 5d19a403@... [N1MMLoggerplus] wrote:

Gerald,

Yes I am able to access it via my browser.  It seems to be isolate to Logger +.  I am able to update the CTY.dat file via Logger +.  It is just trying to update the check partial via logger + that it throws the error.  No firewall or internet blockages.

I downloaded it manually and updated it that way but be advised it throws an error when trying to update via Logger +.  Using latest version.

Anthony 


Re: Updating The Check Partial

5d19a403@...
 

Gerald,

Yes I am able to access it via my browser.  It seems to be isolate to Logger +.  I am able to update the CTY.dat file via Logger +.  It is just trying to update the check partial via logger + that it throws the error.  No firewall or internet blockages.

I downloaded it manually and updated it that way but be advised it throws an error when trying to update via Logger +.  Using latest version.

Anthony 


Re: Contest supporting CW, SSB, RTTY & PSK31

Rick Ellison
 

I do not see that here. If I switch to RTTY then I can transmit after the switch is done. How are you keying your radio? What engine are you sing for RTTY? Does Fldigi close completely when you type RTTY??

 

73 Rick N2AMG

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Friday, September 25, 2015 12:20 AM
To: N1MMLoggerplus@...
Subject: Re: [N1MMLoggerplus] Contest supporting CW, SSB, RTTY & PSK31

 

 

that's what I discovered.  I also discovered if you have the fldigi window open (running PSKmode) then switch to RTTY mode then RTTY won't work.  Seems that FLDIGI must be hogging a driver or something, PSK will work but not RTTY.  Restarting N1MM+ and launching RTTY works fine, then switch to PSK mode and that works.  Switch back to Rtty after this and Rtty doesn't work.  I've discovered you must close the FLDIGI waterfall window, then you'll get and error stating that Fldigi is not longer responding and he Digital Interface Window 1 will now close.  Switch to RTTY mode and all works.

 

Seems like a bug.  It would be great if you could just type RTTY or PSK31 in the CQ-Frequency window and all would work right... 

 

On Thu, Sep 24, 2015 at 3:40 PM, Rick Ellison rellison@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:

 

To change between engines there is a menu selection of the top of the digital window that says Interface. If you have paths set in the config for the various engines and the logger can find them there will be an entry created in the drop down menu that is shown when you click on the Interface menu. Also by clicking on the setup menu then selecting Settings the Digital setup window will open. On the lower half of the pane that is shown you can select the default engines for RTTY and PSK. Once those are set that engine will open whenever you click on either the RTTY or PSK band buttons. Or when you type RTTY or PSK in the entry windows call sign box..

 

73 Rick N2AMG

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Thursday, September 24, 2015 7:41 AM
To: N1MMLoggerplus@...
Subject: [N1MMLoggerplus] Contest supporting CW, SSB, RTTY & PSK31

 

 

I believe the SC QSO party last weekend supported RTTY, PSK31, CW and SSB.  I spent too much time trying to figure out how to get N1MM+ to properly operate on RTTY and PSK31, so I'm looking for some advice.

 

My Rig (Kenwood TS-2000) I have working great stand alone applications on my Windows 7 laptop.  For RTTY use, MMTTY works great and have the EXTFSK 2.0e driver installed. That operates the rig in FSK mode.  For PSK31 I have Fldigi and Flrig set up correctly and the rig operates in USB mode.  For CW I use HRD (and N1MM+) when I don't want to key manually and that all works fine too.  So physical  and electrical connection are all functional, and using the programs listed all works great.  Trying to get N1MM+ to integrate these modes together seems impossible.  The one mode I can't seem to get working is PSK31.  

 

An example, using the SC QSO party as an example, if I click on 20 in the DIG column on N1MM+ main window RTTY Engine 1 is displayed.  How does one tell N1MM+ I want RTTY vs PSK31?  I've tried setting up Fldigi within N1MM+ but that doesn't seem to work.  In the Configurer Digital Modes tab I've pointed to the path for MMTTY (FSK mode) for d1-1 and for the D1-1 Fldigi path I've pointed to that path as well (running win7 so I moved the fldigi.exe file to the \user\username\n1mm+ created folder as there is issues running from the default fldigi folder).

 

I'm at a loss and looking for help. 

 

73,

 

Steve - KC1AXJ

 


Re: duplicate ports

Vytenis LY5T
 

Hi

I'm glad it has helped.
For me it did not work. What worked for me was what pkjahnberge and John k3CT said. I found duplicate ports in registry:
HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\SERIALCOMM (Thats on WinXP)
There were two COM5. One was deleted and seems everything is OK now.

Vytenis
ly5t


---In N1MMLoggerplus@..., <a.wouterson@...> wrote :

Op 25-9-2015 om 11:39 schreef Ad Wouterson:

Peter,

With the excellent help of Vytenis, I found 4 phantom ports. After de-installation all problems now really solved.
This is what he did:
==============================================
What I did was:
Open command prompt with Start - Run - cmd - Enter
Enter command into command prompt: set devmgr_show_nonpresent_devices=1  andpress Enter
OpenControl panel, Device manager. From its menu select View - Hidden devices.
Here, under ports section phantom ports are grayed out. you'd need to uninstall them.
Voila!

goodluck
Vytenis
=============================================

73
Ad/PA2PCH

Op 25-9-2015 om 9:32 schreef pkfalkensee@... [N1MMLoggerplus]:
 

Easy - search the registry for the duplicate com port and rename the one, which is not assigned to an "real" Com port. I had this challenge some month and had to search/replace it in the registry direct.
There was a HW which assigned an com port without beeing an real one :)




Re: duplicate ports

Ad Wouterson <a.wouterson@...>
 

Op 25-9-2015 om 11:39 schreef Ad Wouterson:

Peter,

With the excellent help of Vytenis, I found 4 phantom ports. After de-installation all problems now really solved.
This is what he did:
==============================================
What I did was:
Open command prompt with Start - Run - cmd - Enter
Enter command into command prompt: set devmgr_show_nonpresent_devices=1  and press Enter
Open Control panel, Device manager. From its menu select View - Hidden devices.
Here, under ports section phantom ports are grayed out. you'd need to uninstall them.
Voila!

good luck
Vytenis
=============================================

73
Ad/PA2PCH

Op 25-9-2015 om 9:32 schreef pkfalkensee@... [N1MMLoggerplus]:
 

Easy - search the registry for the duplicate com port and rename the one, which is not assigned to an "real" Com port. I had this challenge some month and had to search/replace it in the registry direct.
There was a HW which assigned an com port without beeing an real one :)




Re: Score Reporting Server

John Bednar
 

Mat,

 

Yes, from the Release Notes for version 1.0.4998:

 

Allow user to enter any URL for the realtime score reporting server. (K6TU) (Coded by N2IC)

 

John, K3CT

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Thursday, September 24, 2015 5:49 PM
To: n1mmloggerplus@...
Subject: [N1MMLoggerplus] Score Reporting Server

 

 

Hi to All!!

 

Reading the help off N1MM plus, i saw this… “Score Reporting Server - At this time, the only real-time score reporting server is cqcontest.net. If any when others become available, they will be added.”

 

Is there any way to change this, for testing only and use a private Reporting Server??? I want to play with this option, but I can´t find where I can add my own server URL, and the messages that the program wait to run.

 

Thanks in advance

73s

Mat LU9CBL

 


El software de antivirus Avast ha analizado este correo electrónico en busca de virus.
www.avast.com

 


Re: duplicate ports

DF1LX-Peter
 

Easy - search the registry for the duplicate com port and rename the one, which is not assigned to an "real" Com port. I had this challenge some month and had to search/replace it in the registry direct.
There was a HW which assigned an com port without beeing an real one :)


Re: Contest supporting CW, SSB, RTTY & PSK31

Steve Allen
 

that's what I discovered.  I also discovered if you have the fldigi window open (running PSKmode) then switch to RTTY mode then RTTY won't work.  Seems that FLDIGI must be hogging a driver or something, PSK will work but not RTTY.  Restarting N1MM+ and launching RTTY works fine, then switch to PSK mode and that works.  Switch back to Rtty after this and Rtty doesn't work.  I've discovered you must close the FLDIGI waterfall window, then you'll get and error stating that Fldigi is not longer responding and he Digital Interface Window 1 will now close.  Switch to RTTY mode and all works.

Seems like a bug.  It would be great if you could just type RTTY or PSK31 in the CQ-Frequency window and all would work right... 

On Thu, Sep 24, 2015 at 3:40 PM, Rick Ellison rellison@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

To change between engines there is a menu selection of the top of the digital window that says Interface. If you have paths set in the config for the various engines and the logger can find them there will be an entry created in the drop down menu that is shown when you click on the Interface menu. Also by clicking on the setup menu then selecting Settings the Digital setup window will open. On the lower half of the pane that is shown you can select the default engines for RTTY and PSK. Once those are set that engine will open whenever you click on either the RTTY or PSK band buttons. Or when you type RTTY or PSK in the entry windows call sign box..

 

73 Rick N2AMG

 

From: N1MMLoggerplus@... [mailto:N1MMLoggerplus@...]
Sent: Thursday, September 24, 2015 7:41 AM
To: N1MMLoggerplus@...
Subject: [N1MMLoggerplus] Contest supporting CW, SSB, RTTY & PSK31

 

 

I believe the SC QSO party last weekend supported RTTY, PSK31, CW and SSB.  I spent too much time trying to figure out how to get N1MM+ to properly operate on RTTY and PSK31, so I'm looking for some advice.

 

My Rig (Kenwood TS-2000) I have working great stand alone applications on my Windows 7 laptop.  For RTTY use, MMTTY works great and have the EXTFSK 2.0e driver installed. That operates the rig in FSK mode.  For PSK31 I have Fldigi and Flrig set up correctly and the rig operates in USB mode.  For CW I use HRD (and N1MM+) when I don't want to key manually and that all works fine too.  So physical  and electrical connection are all functional, and using the programs listed all works great.  Trying to get N1MM+ to integrate these modes together seems impossible.  The one mode I can't seem to get working is PSK31.  

 

An example, using the SC QSO party as an example, if I click on 20 in the DIG column on N1MM+ main window RTTY Engine 1 is displayed.  How does one tell N1MM+ I want RTTY vs PSK31?  I've tried setting up Fldigi within N1MM+ but that doesn't seem to work.  In the Configurer Digital Modes tab I've pointed to the path for MMTTY (FSK mode) for d1-1 and for the D1-1 Fldigi path I've pointed to that path as well (running win7 so I moved the fldigi.exe file to the \user\username\n1mm+ created folder as there is issues running from the default fldigi folder).

 

I'm at a loss and looking for help. 

 

73,

 

Steve - KC1AXJ



Re: Contest supporting CW, SSB, RTTY & PSK31

Steve Allen
 

I have set the mode toe mixed+dig, but only three modes show up: CW, PH and DIG.  Not CW, PH, RTTY and PSK as you describe.

kc1AXJ

On Thu, Sep 24, 2015 at 1:58 PM, ve3ki@... [N1MMLoggerplus] <N1MMLoggerplus@...> wrote:
 

In the Contest Setup you need to select MIXED+DIG as the contest mode. You should now see four columns of band buttons, for CW, PH, RTTY and PSK. You can switch modes either by clicking on the appropriate button or by typing the mode name (e.g. PSK31 or RTTY) into the Entry window call sign box and pressing the Enter key. Note that changing modes between RTTY and PSK31 will cause the digital engine to change between the default interfaces you have selected for those modes in the Digital Setup window. Typing CW, LSB or USB into the Entry window, or clicking on a CW or PH button, will close the DI window.


73,
Rich VE3KI



---In N1MMLoggerplus@..., wrote :

I believe the SC QSO party last weekend supported RTTY, PSK31, CW and SSB.  I spent too much time trying to figure out how to get N1MM+ to properly operate on RTTY and PSK31, so I'm looking for some advice.


My Rig (Kenwood TS-2000) I have working great stand alone applications on my Windows 7 laptop.  For RTTY use, MMTTY works great and have the EXTFSK 2.0e driver installed. That operates the rig in FSK mode.  For PSK31 I have Fldigi and Flrig set up correctly and the rig operates in USB mode.  For CW I use HRD (and N1MM+) when I don't want to key manually and that all works fine too.  So physical  and electrical connection are all functional, and using the programs listed all works great.  Trying to get N1MM+ to integrate these modes together seems impossible.  The one mode I can't seem to get working is PSK31.  


An example, using the SC QSO party as an example, if I click on 20 in the DIG column on N1MM+ main window RTTY Engine 1 is displayed.  How does one tell N1MM+ I want RTTY vs PSK31?  I've tried setting up Fldigi within N1MM+ but that doesn't seem to work.  In the Configurer Digital Modes tab I've pointed to the path for MMTTY (FSK mode) for d1-1 and for the D1-1 Fldigi path I've pointed to that path as well (running win7 so I moved the fldigi.exe file to the \user\username\n1mm+ created folder as there is issues running from the default fldigi folder).


I'm at a loss and looking for help. 


73,


Steve - KC1AXJ



Re: Updating The Check Partial

gbyahoo@...
 

Anthony,

Both files are currently accessible to me and they both update correctly using N1MM+. Have you checked if you can access the scp file directly by using your browser?


Perhaps there is an external internet routing issue or your firewall or anti-virus software is getting in the way.

>> Gerald, VE1DT


Updating The Check Partial

5d19a403@...
 

I am attempting to update the Latest Check Partial File (master.scp) and Logger Plus is not connecting to the internet to get the file.  I am able to download the latest cty.dat file via Logger plus via the internet but not the latest Check Partial file.


Thanks for any help.


Anthony


Re: TS-990S and DigiKeyer II CW Problems

KB3Z
 

I set the rear jack to straight key and not everything works just fine. I have learned something new today. Who would have thought!! Mark KB3Z


Re: TS-990S and DigiKeyer II CW Problems

John Bednar
 

Mark, 

Change the radio key jack for computer keying. Sounds like it's set for paddle keying.

John, K3CT


-------- Original message --------
From: "pastormg2@... [N1MMLoggerplus]"
Date:09/24/2015 7:34 PM (GMT-05:00)
To: N1MMLoggerplus@...
Subject: [N1MMLoggerplus] TS-990S and DigiKeyer II CW Problems

 

Good Evening,
I just connected the Digikeyer II to my 990S. The winkeyer keys the tranmitter. It sends CW, but the problem is it's not sending what it is supposed to be sending. It sends a bunch of T's and M's. I not sure if there is a special menu setting within the 990S that I need to set to have it send the proper characters or not. Any suggestions? I am going to write a note on N1MM plus reflector also. Mark Griffin, KB3Z