On Wed, 17 Jul 2019 18:00:58 -0400
"John Bednar via Groups.Io" <firstname.lastname@example.org> wrote:
I just tested using the ARRL June VHF contest. As I expected, entering a
callsign and pressing the Tab key DOES populate the exchange box from call
history and place the cursor in the RST field.
Oh, now that is very interesting! It doesn't do that on my installation -
if I tab from the Callsign box then it goes to Sent RST but doesn't fill
in the locator from the history - it only does it with space for me.
I wonder if this has something to do with the use of a UDC here ?
The code also places the cursor in the RST box at the location to update
Yes, it does advance to the Sent RST for me also - if memory serves it is
placed after a 5 when using the tab (would need to check).
As Andy GD0AMD points out, we send real signal reports AND we are
penalised if we get them wrong - so they have to match. Real
signal reports means that the 5 is NOT a given - think we have
given out a 31 before now.... and someone even once sent out
something like a 40 which caused some controversy, since 0
suggests NO signal - when that operator probably MEANT the
signal wasn't moving the S meter at all. I digress. Correcting
a 5 is easy with the delete key when you're already past it,
but having to shift-tab (or mouse) all the way back (and then
also have to replace the default 59) is more of a pain.
I was careful to request this as an OPTION - that way it
means that it doesn't affect the normal operation for
those whose signal reports aren't important, but for those
of us penalised for getting them wrong, there is a more
fluid path available than what space bar offers right now.
Pressing tab again advances the cursor to the RST box highlighting the
correct character again.
Well, it looks like there is light at the end of this tunnel. That's
pretty much the way I would want it in Run mode, and worst case in
S&P one could tab twice past the locator to be back in the sent
signal report :) Just need to figure out how to make my copy do
that now :)
From: N1MMLoggerPlus@groups.io [mailto:N1MMLoggerPlus@groups.io] On Behalf
Of Patrick Herborn
Sent: Wednesday, July 17, 2019 10:34 AM
Subject: [N1MM+] Tab / Space behaviour on VHF contests
Good afternoon all!
This question / feature request pertains to the action of Tab and Space
when in a VHF contest. Space is most useful insofar as it will pre-fill
the locator information if pressed in the Callsign field (if using
history lookup), BUT in doing so it jumps directly to the received
serial box, pre-filling the sent and received reports with 59.
This behaviour is fine on HF contests, but we tend to send real signal
reports, which means one then has to go back to correct the pre-filled
signal reports. Occasionally one might have to correct the locator
for a /P but that's just life.
One way of avoiding this is to use the Tab key - this steps through
the fields and permits entry of RS(T) and serial, but then it doesn't
pre-fill the locator. Kind of damned if you do, damned if you don't.
It would be useful to have an option for Space (or some other key)
to pre-fill the locator only, and jump to the relevant next
field (as discussed below).
An additional improvement might be to change the Tab order of the
fields - again this is related to the use of real signal reports.
The default behaviour is to go from the callsign to the sent
signal report - this is fine in Run mode where you just have
to give the best report you can based on receiving just a callsign,
but in S&P you get your report from the Run station, which
allows a better determination of an accurate signal report, ergo
the sent report tends to get filled in last. It would be helpful
to have an option to change the tab (or space or other key) order to
Callsign->RxRST->RxSn->Loc->SntRST - perhaps tracking Run/S&P state.
These things may of course already be possible - I just haven't found a
way of doing it - in which case I should be grateful for any hints /
tips / instructions.
Patrick Herborn <pat@...>
Patrick Herborn <pat@...>