Dear All, up to now I had only timeliness minimum/maximum values in seconds. For users who try to adapt my cron.cmd in SPS V4.0 (Beta) I have measured and plotted timeliness for all useful EUMETCast c

Good day all. With David’s help again my system is almost running successfully on my new settings using TBS dual mode for basic and HVS-1. The SR-1 is also back in business on the new HVS-2. But the t

Hello All, MTG-I1 has now been fully fuelled ready for a scheduled launch on December 13th. https://www.esa.int/Applications/Observing_the_Earth/Meteorological_missions/meteosat_third_generation/New_w

JFYI Cheers, U. ------- Weitergeleitete Nachricht / Forwarded message ------- An: "MTG" <MTG-1@...> Kopie an: <MSG-1@...> Von: "David J Taylor" <david-taylor@...> Datum: Thu, 7 Feb 2013 14:44:27 -0000

Hello, We installed Tellicast (2.14.7) using UBUNTU “server” 22.04 and received segfault from tc-cast-client -k. We used safenetauthenticationclient 9.0.43-0 and 10.7.77 drivers but with the same resu

I’m trying to track down a couple of issues affecting the dual tap setting which now reports it can’t be set, following my attempt to reconfigure the two for basic and hvs1. I have Windows backup but

Fascinating to see EUTELSAT 10B slowly moving into position! At the moment it's at about 83 degrees east, with the figure of 8 orbit just visible (the orange and blue line). Cheers, David -- SatSignal

I am seeing an increase today in the basic/HVS-1 signal of approx. 0.3dB on the SNR. Always welcome especially up here in Angus. Unfortunately the new vertical signal for HVS-2 is still extremely poor

Hello everyone Since last night I have no signal on my HV2 receiver (11 387.5 mHz): Did I miss something? Manu

Hello, When will this switch-migration take place ?? Kindly advise. Thanks in advance, Regards Roland

For those using an Ayecka SR1 for HVS-2 reception, renumber to set the vertical polarisation by setting the "LNB power" to 18V. Screen-shot attached. Use your "single-cable, dual tuner" for BAS on one

Folks, The clock is now ticking - with the final transmission of the old HVS-1 service planned for December 23. This year! https://www.eumetsat.int/eumetcast-europe-service-transponder-migration By th

David I am using the Ayecka SR1 at the moment for basic/HVS-1 service and the setting is for 18v. Is vertical not 13v. Regards Ian.

Hi all, Wasn't sure whether to reply to one of the specific threads or just go with a new one - but going with the latter. On my previous Inverto White Tech C120 quad LNB, since replaced after finding

Hello All, Did we miss this? Not that it will presumably not make any different to users - yet. https://www.eumetsat.int/new-uplink-service-eumetcast-europe Also - and "please do not adjust your set"

Folks, while browsing through some recently downloaded docs from Eumetsat and Ayecka and looking here and there in the SR1 via telnet, I stumbled over an entry 'Air IP', here set to 192.~.161 . That t

Hi all, I feel like I've missed something painfully obvious but I've dug through the config files and scripts and can't seem to find what I'm missing. When I've tested HVS-2 on 11263 V or the HB13 ser

Unfortunately the Metop scripts don't work for AVHRRL1 data files from Internet. This is for V3.0, but as far as I can see also the case for v4.0. These files have 90 minutes in one file; nearly 500M

SpaceX is targeting Monday, November 21 for launch of the Eutelsat 10B mission to a geosynchronous transfer orbit from Space Launch Complex 40 (SLC-40) at Cape Canaveral Space Force Station in Florida

Folks, I'm getting complaints about the number of messages relating to 'Satpy Processing System" (SPS)' and I know a small number of folk have left the group as a result. Groups.IO has the ability to