Date
1 - 4 of 4
Ayecka SR1 in a multiswitch system
|
Matthias
Can anyone tell me how to configure an Ayecka SR1 when using it in a 2 LNB multiswitch system? For my other receiver (a TBS 5927) for example I have to set Diseqc to "Position B" and "Option A" to receive data from Eutelsat 10A.
Currently I use these settings with my SR1 (still with no luck): K. DiSEqC Switch Control SAT B
L. DiSEqC General Command 0x0
Any idea what settings are needed here?
Matthias
|
|
|
|
Matthias
Ok, perhaps more information is needed.
So, here are my settings: RX 1 Configuration ==================
1. Configuration Set 1 Active
2. Configuration Set 2 Not Active
3. Search Enable Enabled
4. Configuration Sets Management
> 1
Configuration Set 1
===================
1. Tuner Frequency 1512.500 MHz
2. Tuner Acquisition Bandwidth 10.000 MHz
3. Standard DVB-S2
4. Coding Mode VCM
5. Symbol Rate Auto
6. MODCOD Auto
7. RollOff Auto
8. Pilot Auto
9. Spectral Inversion Auto
A. Gold Code 0
B. Frame Type Auto
C. Encapsulation MPEG-TS
D. ISI 1
E. Filters Table
F. LNB power 18V
G. LNB compensation Off
H. 22 KHz Off
I. Status Active
J. Profile Name EUMETCast DVB-S2 T1
K. DiSEqC Switch Control SAT B
L. DiSEqC General Command 0x0
M. Tuner Filter Bandwidth 72.000 MHz
================================================================================
SR1c Serial No. 103777 30AAC Run Time: 0:15:45
SW Ver 1.05b265 V HW Ver 2.02 FW Ver 2.02b022 V BL Ver 1.01b15
RX1: Active, Not Locked
EUMETCast DVB-S2 T1 1512.500 MHz, Auto
RX2: Not Active, Not Locked
Profile 1 1100.000 MHz, Auto
================================================================================
As you can see I get no lock. What is wrong with my settings? Matthias
|
|
|
|
Matthias
My dish should be well aligned since my other receiver (a TBS 5927) works very well with my EUMETCast system.
|
|
|
|
Ok, perhaps more information is needed.
So, here are my settings: RX 1 Configuration ================== 1. Configuration Set 1 Active 2. Configuration Set 2 Not Active 3. Search Enable Enabled 4. Configuration Sets Management 1Configuration Set 1 =================== 1. Tuner Frequency 1512.500 MHz 2. Tuner Acquisition Bandwidth 10.000 MHz 3. Standard DVB-S2 4. Coding Mode VCM 5. Symbol Rate Auto 6. MODCOD Auto 7. RollOff Auto 8. Pilot Auto 9. Spectral Inversion Auto A. Gold Code 0 B. Frame Type Auto C. Encapsulation MPEG-TS D. ISI 1 E. Filters Table F. LNB power 18V G. LNB compensation Off H. 22 KHz Off I. Status Active J. Profile Name EUMETCast DVB-S2 T1 K. DiSEqC Switch Control SAT B L. DiSEqC General Command 0x0 M. Tuner Filter Bandwidth 72.000 MHz ================================================================================ SR1c Serial No. 103777 30AAC Run Time: 0:15:45 SW Ver 1.05b265 V HW Ver 2.02 FW Ver 2.02b022 V BL Ver 1.01b15 RX1: Active, Not Locked EUMETCast DVB-S2 T1 1512.500 MHz, Auto RX2: Not Active, Not Locked Profile 1 1100.000 MHz, Auto ================================================================================ As you can see I get no lock. What is wrong with my settings? Matthias =================================== Matthias, I'm using a direct connection to an outlet of a quad LNB. The only significant difference I see is: You: *K. DiSEqC Switch Control SAT B* Me: K. DiSEqC Switch Control SAT A Minor differences: 1. Tuner Frequency 1513.000 MHz J. Profile Name EUMETCast DVB-S2 I have no experience of multi-switch systems. Looks like no signal is getting to the device. Can you try a direct connection just for a test? My headline shows a 12.2 dB Es/No value, yours shows none: SR1c Serial No. 104670 30AAC Run Time: 330:43:10 SW Ver 1.05b264 V HW Ver 2.05 FW Ver 2.02b022 V BL Ver 1.01b14 RX1: Active, Locked EUMETCast DVB-S2 1513.000 MHz, Dummy PLframe, 32.993 Msps, ACM, 12.2 dB RX2: Not Active, Not Locked Profile 1 1100.000 MHz, Auto Cheers, David -- SatSignal Software - Quality software for you Web: https://www.satsignal.eu Email: david-taylor@blueyonder.co.uk Twitter: @gm8arv
|
|
|