Topics

Ayecka SR1 in a multiswitch system


Matthias
 

 
Can anyone tell me how to configure an Ayecka SR1 when using it in a 2 LNB multiswitch system? For my other receiver (a TBS 5927) for example I have to set Diseqc to "Position B" and "Option A" to receive data from Eutelsat 10A. 

Currently I use these settings with my SR1 (still with no luck):  
 
K. DiSEqC Switch Control SAT B
L. DiSEqC General Command 0x0 
 
Any idea what settings are needed here?
 
Matthias


Matthias
 

Ok, perhaps more information is needed. 
So, here are my settings:

RX 1 Configuration
==================
1. Configuration Set 1                  Active
2. Configuration Set 2                  Not Active
3. Search Enable                        Enabled
4. Configuration Sets Management
 
> 1
 
Configuration Set 1
===================
 
        1. Tuner Frequency              1512.500 MHz
        2. Tuner Acquisition Bandwidth  10.000 MHz
        3. Standard                     DVB-S2
        4. Coding Mode                  VCM
        5. Symbol Rate                  Auto
        6. MODCOD                       Auto
        7. RollOff                      Auto
        8. Pilot                        Auto
        9. Spectral Inversion           Auto
        A. Gold Code                    0
        B. Frame Type                   Auto
        C. Encapsulation                MPEG-TS
        D. ISI                          1
        E. Filters Table
        F. LNB power                    18V
        G. LNB compensation             Off
        H. 22 KHz                       Off
        I. Status                       Active
        J. Profile Name                 EUMETCast DVB-S2 T1
        K. DiSEqC Switch Control        SAT B
        L. DiSEqC General Command       0x0
        M. Tuner Filter Bandwidth       72.000 MHz


================================================================================
SR1c Serial No. 103777  30AAC                              Run Time:    0:15:45
SW Ver  1.05b265  V     HW Ver  2.02    FW Ver  2.02b022 V      BL Ver  1.01b15
 
RX1: Active, Not Locked
 EUMETCast DVB-S2 T1 1512.500 MHz, Auto
 
RX2: Not Active, Not Locked
 Profile 1 1100.000 MHz, Auto
 
================================================================================

As you can see I get no lock. What is wrong with my settings?

Matthias
 


Matthias
 

My dish should be well aligned since my other receiver (a TBS 5927) works very well with my EUMETCast system. 


Matthias


David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺
 

Ok, perhaps more information is needed.
So, here are my settings:


RX 1 Configuration
==================
1. Configuration Set 1 Active
2. Configuration Set 2 Not Active
3. Search Enable Enabled
4. Configuration Sets Management

1
Configuration Set 1
===================

1. Tuner Frequency 1512.500 MHz
2. Tuner Acquisition Bandwidth 10.000 MHz
3. Standard DVB-S2
4. Coding Mode VCM
5. Symbol Rate Auto
6. MODCOD Auto
7. RollOff Auto
8. Pilot Auto
9. Spectral Inversion Auto
A. Gold Code 0
B. Frame Type Auto
C. Encapsulation MPEG-TS
D. ISI 1
E. Filters Table
F. LNB power 18V
G. LNB compensation Off
H. 22 KHz Off
I. Status Active
J. Profile Name EUMETCast DVB-S2 T1
K. DiSEqC Switch Control SAT B
L. DiSEqC General Command 0x0
M. Tuner Filter Bandwidth 72.000 MHz



================================================================================
SR1c Serial No. 103777 30AAC Run Time: 0:15:45
SW Ver 1.05b265 V HW Ver 2.02 FW Ver 2.02b022 V BL Ver 1.01b15

RX1: Active, Not Locked
EUMETCast DVB-S2 T1 1512.500 MHz, Auto

RX2: Not Active, Not Locked
Profile 1 1100.000 MHz, Auto

================================================================================

As you can see I get no lock. What is wrong with my settings?

Matthias
===================================

Matthias,

I'm using a direct connection to an outlet of a quad LNB. The only significant difference I see is:

You:
*K. DiSEqC Switch Control SAT B*

Me:
K. DiSEqC Switch Control SAT A

Minor differences:

1. Tuner Frequency 1513.000 MHz
J. Profile Name EUMETCast DVB-S2

I have no experience of multi-switch systems. Looks like no signal is getting to the device. Can you try a direct connection just for a test? My headline shows a 12.2 dB Es/No value, yours shows none:

SR1c Serial No. 104670 30AAC Run Time: 330:43:10
SW Ver 1.05b264 V HW Ver 2.05 FW Ver 2.02b022 V BL Ver 1.01b14

RX1: Active, Locked
EUMETCast DVB-S2 1513.000 MHz, Dummy PLframe, 32.993 Msps, ACM, 12.2 dB

RX2: Not Active, Not Locked
Profile 1 1100.000 MHz, Auto

Cheers,
David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@...
Twitter: @gm8arv