Beautiful tutorial ... it would have been nice to have had it 10 years ago !!! anyway ...it would have been nice if he had spoken more slowly ... not everyone understands english word for word (me in

David> The last time I used the system I regularly received both MTB and MTC and since then in my configuration nothing has changed also because I only configured BASIC reception Ernest> YES, I had re

Hello everyone sorry for the inconvenience. I reactivated the MSG system after a few months of stand by and I noticed the lack of METOP-C data in the EPS10 folder. I searched the forum but found no po

Ho to all, time ago i have had the same problem. I had solved resolder (hot air) the uart chip in sr1. Also,via putty,sr1 can be controlled via Lan (management port). Sorry but, with Smart phone the i

Johm... Here in Italy, near Novara, until a few days ago if you wanted to cook eggs it was enough that you went on a roof and broke them on the tiles. In a few seconds the egg was cooked !!! Come on .

Ho John, thank's for you report! My descent cable is about 30 meters. An old LNB plus a very long descent are a very bad pairing. I looked at the BLAK ULTRA 1 exit because they give it a suitable fit

Ferdinand ,David I thank you for the exhaustive details. The replacement of the LNB is due to the fact that it is very old (almost 15 years, bought to use on HB13) and the cost is quite affordable to

good morning to all. I have read that to receive the 3 eumetsat services at the same time it is necessary to have at least two receivers: one for BAS and HVS1 tuned to transponder 1 and one for HVS2 t

David..thanks for the encouragement !! Now, this evening afther "concrete"....I'll install the bas only CFG, like from your suggest! Mi dish is an old 85cm and when I transferred the whole satellite s

Ciao David....hard day...today!!!! 1st floor done.... tomorrow the second one!! For today I've stopped the "concrete" job and now,start the "electronic" job... :)) Anyway.... I've read the signal from

Hi David, this morning I'm tired, I'm changing the floors of the house and so I don't want to think ... I asked google translator for help. I tried to read mail on my smartphone but I realized that th

Sorry ,but using smartphone with auto correcor in italiano,is hard writhe in enghlish! :) ***************************************************************************** Mario Brustia - IZ1KBP Pilota SA

Ciao David, Yes,i have seen these scripts some days ago.when I upgraded the sr1,like you post,i hard upload the eumetsat Script tool (1st to 4th). I have make many test befor ask in forum,but without

I have not found Any script on umetsat Ftp site. I have found only bios/firmware upgrade end tellicast procedure/software. Have you the correct link ti the script? Tnx in avance Mario ****************

mmmm...sorry...in the eumetsat guide I read about enabling configuration setting 2 for the receiver 1. I entered them in the current configuration together with the bas pids. Is it wrong? mmmm....

Ciao David... Yes PID 600 and 601 are anabled...I'll do a more deep investigation (may be a wrong configuration ?) may be.... the usual problem: worng interpretation of an english tech documentation!

Hi David ... a doubt: I changed the code like from your site (H41000).Bas service is ok (withe icon) ,Hvs1 is in connect status (Yellow icon but license tab ok). Question: HVS1 is sent by eumetsat by

The problem was due to hardware key.WIth the new key all works fine! Thank's to eumetsat staff for support! mario

Ciao David... Thank's a lot!! Unfortunately, in website there is a lot of link/sub page and , afther a long trip, I'm lost in "htlm space"!! In my last chek (last week), I had not found your link. Now

Ciao David, thank's so much for you words about my "english" !!! ;) Ok for managment port usage: my sr1 is already configured, I must only monitor the status. However, today, I've found the fault: I'v