Date   

Re: Help in the beginning

David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺
 

On 29/11/2020 11:13, Giftmacher via groups.io wrote:
Ok, since I have no other coaxial cable, I have tried the RAMdisk according to this article
https://www.satsignal.eu/wxsat/atovs/RAMdisk.pdf <https://www.satsignal.eu/wxsat/atovs/RAMdisk.pdf> Now I see messages like this:
ERR:2020-11-29 11:10:40.806:Could not join channel "EPS-10": Missing key 58020.
Weak signal or other errors. Could be a wobbly dish.

David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv


Re: Help in the beginning

Giftmacher
 

Ok, since I have no other coaxial cable, I have tried the RAMdisk according to this article
https://www.satsignal.eu/wxsat/atovs/RAMdisk.pdf Now I see messages like this:
ERR:2020-11-29 11:10:40.806:Could not join channel "EPS-10": Missing key 58020.


Re: Help in the beginning

David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺
 

On 29/11/2020 09:02, Giftmacher via groups.io wrote:
Maybe the repeater USB cable isn't best idea. Most of the pictures are incomplete.
I think it more likely to be one of the PC issues I mentioned, but try a longer RF lead as a test. The RF gain is in the LNB, so longer cables can be tolerated.

David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv


Re: Help in the beginning

Giftmacher
 

Maybe the repeater USB cable isn't best idea. Most of the pictures are incomplete.


Re: Help in the beginning

David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺
 

On 29/11/2020 06:30, Giftmacher via groups.io wrote:
Thank you! Is there any good tutorial for any from these programs? I also get often missed parts error. Do I need to improve SNR?
There's a lot of good advice in the EUMETSAT guides for each receiver type. The best guide to performance is the Link Margin, which should be at least 4 dB for most reliable reception. For example Rungsted in the graphs here:


https://www.satsignal.eu/mrtg/performance_eumetcast-europe_link_margin.php

This implies an SNR of about 13.5 dB. The SNR for the Basic Service alone can be quite a bit less, perhaps about 10 dB. The 4 dB margin allows for some degradation due to rainfall, ice-crystals in the clouds, an so forth.

In the receiver PC itself, things to watch out for are:

- network I/O - may not apply to the TBS5927

- USB load - perhaps use a separate USB 3.0 connection?

- disk I/O - is anything hammering the disk?

- CPU load - is something else stealing CPU cycles?

- do you have "temp" and "received" on the same partition?

Many of use us a RAMdisk to alleviate slow disk I/O issues. Some of the systems here use a RAMdisk for the TelliCast "received" and "temp" directories, with a job running at (say) every minute to copy/move the received data from RAMdisk to HD, where it is picked up by the processing programs (my own software, in my case).

Ask here if you need more help - there's a lot of experience!

Cheers,
David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv


Re: Help in the beginning

Giftmacher
 

Thank you! Is there any good tutorial for any from these programs? I also get often missed parts error. Do I need to improve SNR?


Re: Help in the beginning

Ernst Lobsiger
 

Giftmacher

You never get plain images but satellite data from special instruments you can produce images from.
To produce images you can buy David's programs, you can try Hugo's EUMETCastView or Rob's xrit2pic
or you can even give (Open Source) Pytroll/Satpy a go with my Starter_Kit that you find as *.zip on this list..

Good luck
Ernst


Help in the beginning

Giftmacher
 

Hi all, newbie here. Yesterday TBS 5927 USB arrived and I completed the hardware for reception. Today I was able to find the EUTELSAT-10
satellite and achieve signal lock with SNR of 11. Tc-cast-client connects to BAS, HV1 with no problem, sometimes there are various
errors (missing key, missed parts), and all I have received is bunch of bz2 and dat files, no images though.
What I'm doing wrong? Thanks in advance.


Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

geojohnt@...
 

David,

Yes, hadn't thought about that.
However that would be the case in the failure of 10-A.
But this could be achieved (barring fir trees) with a 3 degree offset LNB.

But as Ian and Douglas said we've never known a failure in our long past of receiving 'Meteosat.'
Or did we with direct reception of WEFAX at one time have to repoint to the backup?
But that was different.

Eutelsat 10A and 9-B would be a good joint compromise.
I realise that depends on satellite capacity.

If EUMETSAT do run an extended period of parallel services from both satellites - rather than a couple of days testing - I'll 'try' to find Hot Bird without a major dish relocation to bathe for a while in SNR in the region of 15 dB +++.
A 3 degree offset LNB won't work owing to the fir tree and the dish is up against the kitchen wall.
So mega temporary relocation. 

Regards,
John.

+++++++++++++++

Well, that would be nice, except for the thousands of users who would 
need to get contractors in to re-align their antennas!  Mind you, I will 
look with my spare LNB feed to see what a non-aligned dish might provide.

David
-- 
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@...
Twitter: @gm8arv

++++++++++++++++++

-----Original Message-----
From: David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺 via groups.io <david-taylor@...>
To: MSG-1@groups.io
Sent: Fri, 27 Nov 2020 14:36
Subject: Re: [MSG-1] Migration of EUMETCast Europe restoration capacity to Hotbird 13

On 27/11/2020 12:13, geojohnt via groups.io wrote:
> Hello All,
>
> OK, OK!
>
> I should have read the EUMETSAT notification properly.
>
> Damn, damn, damn, again.
>
> If EUMETSAT are reserving these two transponder on Hot Bird instead of
> 21 E, wouldn't it be better to use (reserve) the current two
> transponders on Eutelsat 10-A as the backup and move operational
> services to Hot Bird - with its obvious power advantages?
>
> Regards,
> John.






Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

Ernst Lobsiger
 

On Fri, Nov 27, 2020 at 06:20 AM, Graham Woolf wrote:
Hi Ernst

Thanks for the info

Are these cards any improvement on the SR1 ?

I assume these https://shop.tbsdtv.com/tbs6909x-dvbs2-octa-tuner-pcie-card-p-207.html  would have the fix

Re FY3D I did run the TCLogging and was missing some files . What I do now is print a list of files from the pass that is being processed and I just check to make sure I have 22

I have incorporated this into all my FY3D,VIIRS and NOAA20 scripts

Regards

Graham
Graham

This card replaces 4 receivers SR1 for the price of app. half an SR1. I have never seen an SR1 perform the way I just described.
Yes, that's AFAIK the shop Christian Peters ordered his card from. TBS does replace older TBS-6909X cards that have problems
because of the 22uF capacitor fix still missing. It even seems they have some Black Friday price right now ...

Regards,
Ernst

P.S. The FY-3D pass does not always have 22 Files. That depends on your ran (range) setting and on being west central or east.
But you should always have an even number of files (1000m image data and accompanying GEO1k geographical reference data).


Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺
 

On 27/11/2020 12:13, geojohnt via groups.io wrote:
Hello All,
OK, OK!
I should have read the EUMETSAT notification properly.
Damn, damn, damn, again.
If EUMETSAT are reserving these two transponder on Hot Bird instead of 21 E, wouldn't it be better to use (reserve) the current two transponders on Eutelsat 10-A as the backup and move operational services to Hot Bird - with its obvious power advantages?
Regards,
John.
Well, that would be nice, except for the thousands of users who would need to get contractors in to re-align their antennas! Mind you, I will look with my spare LNB feed to see what a non-aligned dish might provide.

David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv


Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

Graham Woolf
 

Hi Ernst

Thanks for the info

Are these cards any improvement on the SR1 ?

I assume these https://shop.tbsdtv.com/tbs6909x-dvbs2-octa-tuner-pcie-card-p-207.html  would have the fix

Re FY3D I did run the TCLogging and was missing some files . What I do now is print a list of files from the pass that is being processed and I just check to make sure I have 22

I have incorporated this into all my FY3D,VIIRS and NOAA20 scripts

Regards

Graham


Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

Ernst Lobsiger
 

On Fri, Nov 27, 2020 at 04:10 AM, Graham Woolf wrote:
Hi Ernst

What is the difference between the TBS 6909 and the TBS 6909X V2 or would either do

Regards

Graham
Graham

The TBS-6909 does NOT work for EUMETCast! You need a TBS-6909X. This latter
card comes as TBS-6909X V11 built 2018/2019 and as TBS-6909X V2 built 2020.
Mike and I tested the TBS-6909X V11 in 2018. It was unusable for EUMETCast.
The TBS-6909X V2 has been built to solve more problems of the TBS-6909X V11.
It has four additional VGLNAs (Variable Gain Low Noise Amplifiers). But it
didn't work properly under VCM to begin with either. The difference made an
additional 22uF SMD capacitor that stabilized an on board power supply. With
this fix both cards (the TBS-6909X V11 and TBS-6909X V2) work very well now.

See also: https://groups.io/g/MSG-1/message/30020

You probably will not find a TBS-6909X V11 anymore and if you buy a TBS-6909X
V2 you should do that directly from TBS in China. They hand fixed all their
stock with the 22uF capacitor. Maybe 2021 they will have a design of the V11
or V2 where the 22uF capacitor is integrated on the board from the beginning.

Christian Peters recently bought a TBS-6909X from China and got a 22uF fixed
V2 model. I have no TBS-6909X V2 but four TBS-6909X V11 (2018 and 2019) that
are hand fixed with the 22uF capacitor. Those work *very* well under GNU/Linux.


I have two EUMETCast receivers using the TBS-6909X V11 right now:

Fujitsu/Siemens P7935, 12 years old, Core2 Duo, 8GB RAM, taking BASIC + HVS-1
+ HVS-2 with a single cable using 3 (of 8) demodulators of the TBS-6909X V11:
During the last 22 days this receiver has lost ONE (1) single (Basic) UDP packet.

Fujitsu Celsius W520 Power, 8 years old, Xeon, 24GB RAM, taking BASIC + HVS-1
+ HVS-2 with a single cable using 3 (of 8) demodulators of the TBS-6909X V11:
During the last 22 days this receiver has lost NOT ONE (0!) single UDP packet.

No idea how the cards perform under Windows 10. This hasn't been done yet ...


Cheers,
Ernst


P.S. What did your installation of 3 instances of TClogSummary.cmd reveal?


Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

Douglas Deans
 

On 27/11/2020 10:44, geojohnt via groups.io wrote:
Hugo and All,
Damn, damn, damn,
This is wonderful news for 'those up north ' and in Ireland.
But my SNR with a 1 m dish and SR1 on TP 1 has been 'quite high' over the last few weeks at 13.3 dB to 13.6 dB.
I've even seen a 13.7 dB.
But now I will have to chop down the next door neighbours towering fir tree which blocks every satellite from just east of 10 A to 19.2 degrees east from my patio mounted dish!!!
Poisoning the tree some years ago didn't work.
Regards,
John Tellick.
===============================================================================

John to be honest this news is almost irrelevant. In all my time with Eumetcast going back to Meteosat 6 I have never known the main satellite needing swapped out. Uplink station is of course a different matter.
Permanent change of the main satellite would of course be very welcome up here in Scotland.

Regards,
Douglas.


Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

Ian Deans
 

On 27/11/2020 10:44, geojohnt via groups.io wrote:
Hugo and All,
Damn, damn, damn,
This is wonderful news for 'those up north ' and in Ireland.
But my SNR with a 1 m dish and SR1 on TP 1 has been 'quite high' over the last few weeks at 13.3 dB to 13.6 dB.
I've even seen a 13.7 dB.
But now I will have to chop down the next door neighbours towering fir tree which blocks every satellite from just east of 10 A to 19.2 degrees east from my patio mounted dish!!!
Poisoning the tree some years ago didn't work.
Regards,
John Tellick.
===========================================================

John I wouldn't call it wonderful news for those of us up north as the chances of Hotbird 13 ever being used for Eumetcast are next to nil.
Hotbird 13 will only be used if the the present satellite at 10 degrees completely fails and that has never happened with their main satellite.

I for one would be delighted if Eumetcast moved to 13 degrees, but regrettably it is not going to happen.

Regards
Ian.


Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

geojohnt@...
 

Hello All,

OK, OK!

I should have read the EUMETSAT notification properly.

Damn, damn, damn, again.

If EUMETSAT are reserving these two transponder on Hot Bird instead of 21 E, wouldn't it be better to use (reserve) the current two transponders on Eutelsat 10-A as the backup and move operational services to Hot Bird - with its obvious power advantages?

Regards,
John.

++++++++++++++++++++++++


-----Original Message-----
From: Hugo <hvanruys@...>
To: MSG-1@groups.io
Sent: Thu, 26 Nov 2020 16:48
Subject: [MSG-1] Migration of EUMETCast Europe restoration capacity to Hotbird 13


Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

Graham Woolf
 

Hi Ernst

What is the difference between the TBS 6909 and the TBS 6909X V2 or would either do

Regards

Graham


EUMETCast migration to 'Hot Bird.'

geojohnt@...
 

Hello All,

I meant to attach the new downlink power level plot many of you will enjoy in my last post.
Goodness, here in southern England the predicted power level will go up from 48 dBW to 53 dBW!

Here they are.
Enjoy it you lucky people without neighbours offending trees.

Regards,
John.





Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

Cornish Man
 

Hi

 

Proper Job

 

Never got my signal above 12db with my 110cm down here in Cornwall

 

Jan

 

Sent from Mail for Windows 10

 

From: geojohnt via groups.io
Sent: 27 November 2020 10:44
To: MSG-1@groups.io
Subject: Re: [MSG-1] Migration of EUMETCast Europe restoration capacity to Hotbird 13

 

Hugo and All,

 

Damn, damn, damn,

 

This is wonderful news for 'those up north ' and in Ireland.

 

But my SNR with a 1 m dish and SR1 on TP 1 has been 'quite high' over the last few weeks at 13.3 dB to 13.6 dB.

I've even seen a 13.7 dB.

 

But now I will have to chop down the next door neighbours towering fir tree which blocks every satellite from just east of 10 A to 19.2 degrees east from my patio mounted dish!!!

 

Poisoning the tree some years ago didn't work.

 

Regards,

John Tellick.


++++++++++++++++++++++

-----Original Message-----
From: Hugo <hvanruys@...>
To: MSG-1@groups.io
Sent: Thu, 26 Nov 2020 16:48
Subject: [MSG-1] Migration of EUMETCast Europe restoration capacity to Hotbird 13

 


Re: Migration of EUMETCast Europe restoration capacity to Hotbird 13

geojohnt@...
 

Hugo and All,

Damn, damn, damn,

This is wonderful news for 'those up north ' and in Ireland.

But my SNR with a 1 m dish and SR1 on TP 1 has been 'quite high' over the last few weeks at 13.3 dB to 13.6 dB.
I've even seen a 13.7 dB.

But now I will have to chop down the next door neighbours towering fir tree which blocks every satellite from just east of 10 A to 19.2 degrees east from my patio mounted dish!!!

Poisoning the tree some years ago didn't work.

Regards,
John Tellick.

++++++++++++++++++++++

-----Original Message-----
From: Hugo <hvanruys@...>
To: MSG-1@groups.io
Sent: Thu, 26 Nov 2020 16:48
Subject: [MSG-1] Migration of EUMETCast Europe restoration capacity to Hotbird 13

881 - 900 of 31130