Date   

Re: Updated Tellicast software

Jonathan Williams <jonathan@...>
 

Likewise my experience, only I didn't uninstall, just installed
'over the top'. I am running v4.4.0 of the Skystar driver.

Following Arne's advice, I upped my RAMDisk to 64Mb to
get the updates in the first place.

All in all, very very painless!

Jonathan

----- Original Message -----
From: "David painter" <Painter@oldtrout.freeserve.co.uk>
To: <MSG-1@yahoogroups.com>
Sent: Saturday, May 20, 2006 3:15 PM
Subject: [MSG-1] Updated Tellicast software


All,
received update last night.
Left the USU DVB skystar V4.3.0 driver alone.
removed e_token software and tellicast software and removed USB e-token and
re-booted.

Re-installed e-token, plugged in USB token, then re-installed the tellicast
software and all works fine!

Total process less than 5 minutes.

Cheers
David P


Updated Tellicast software

David painter <Painter@...>
 

All,
received update last night.
Left the USU DVB skystar V4.3.0 driver alone.
removed e_token software and tellicast software and removed USB e-token and re-booted.

Re-installed e-token, plugged in USB token, then re-installed the tellicast software and all works fine!

Total process less than 5 minutes.

Cheers
David P

----- Original Message -----
From: "Vincenzo Mone" <vimone@alice.it>
To: <MSG-1@yahoogroups.com>
Sent: Friday, May 19, 2006 10:58 PM
Subject: R: [MSG-1] Re: About


Hi Arne,
The PDF says:

1. Exit the Tellicast client and Server4Pc programs
(right-click on the icons in the tray and exit)
2. Completely uninstall any existing Technisat DVB software:
- Go to Control "Panel - Add or Remove Programs" and
- select "Technisat DVB Receiver" or similar.
- If asked to "Remove shared file", select "No to All"
I done it but it does not uninstall it.
When I click on it to uninstall, I get and orange page with a warning which
ask me if I want to remove completely the application.
I click on OK so I get another small blue window with a bar but after a
couple of seconds it disappear and remains only the orange page and after a
couple of seconds even the orange page disappears and the application is
still in the add/remove programs.
Why this?
What happens?
Thanks




73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N� 30666121 *****
*** 2nd e-mail: vimone@tin.it ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per conto di
a_van_belle
Inviato: venerd� 19 maggio 2006 23.44
A: MSG-1@yahoogroups.com
Oggetto: R: [MSG-1] Re: About

Hi Vincenzo,

Version 4.2.2 was the recommended one before 4.3.0 and never gave me
any problems.
If all works I would not change it.

A detailed upgrade installation guide is included in the Update you
received from Eumetsat. Goto folder Windows&#92;Skystar_4_3_0_a and open
readme_skystar_xp_v2.pdf (or the w2k version of you use windows2000)

Greetings,
Arne van Belle
--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@...> wrote:

Hi Arne,
I have checked the Skystar/Technisat driver
and have all Version 4.2.2.
Do I need to upgrade it?
If yes which is the procedure.
The eToken in the "Add/Remove programs" is "eToken Run Time Environment
3.65"
Thanks again.


73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N� 30666121 *****
*** 2nd e-mail: vimone@... ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per conto di
a_van_belle
Inviato: venerd� 19 maggio 2006 23.25
A: MSG-1@yahoogroups.com
Oggetto: R: [MSG-1] Re: About

Hello Vincenzo,

You probably did the update correctly. But with so many version
numbers it can be confusing.

Eumetsat's update consists of the Skystar/Technisat driver, which most
of us don't need to update as the same version was already included on
the EUMETCast Client Software V4 CDROM.
To check this Rightclick the (hopefully) green Sat Icon in the tray
and choose "About DVB Receiver"
This should list Version 4.3.0 for all instances.

As Douglas mentioned newer versions are available and these might work
perfectly but are not the recommended/tested one.

To check if the recommended EKU-software has been installed correctly,
look in "Add/Remove programs" for "eToken Run Time Environment 3.65"

The Tellicast version is shown in the uppermost "About tc-recv" and
should read 2.4.4 B .......

Greetings,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@> wrote:

Hi Arne,
what do you mean with:
The telecast version you mention is correct.
4.2.5.4 is the firmware in your EKU, this was not updated.
You mean I did not update it or Eumetsat did not send the update?
Thanks

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N� 30666121 *****
*** 2nd e-mail: vimone@ ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per
conto di
a_van_belle
Inviato: venerd� 19 maggio 2006 22.29
A: MSG-1@yahoogroups.com
Oggetto: [MSG-1] Re: About

Hello Vincenzo,

The double "About" is a minor problem in the new Tellicast
client that
has been reported to Eumetsat already.

The tellicast version you mention is correct.
4.2.5.4 is the firmware in your EKU, this was not updated,
only the
eToken RunTimeEnvironment is updated from 3.51 to 3.65 but it
is not
easy to check this.

Are you sure about TechniSat driver version 4.3.2.9999 ??
The version in EUMETSAT's update is 4.3.0.9999
But if it works, don't fix it !

Greetings,
Arne van Belle


--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@> wrote:

Hi to the list,
after several trials I have done the upgrades.
Now I have noticed that if I right click on the T in the taskbar
Compares two times the words ABOUT TC-RECV.
If I click on the top one I get the information's but If I click
on the
bottom one, nothing happens.
Has anybody noticed it?
Is it normal?
Please are the upgrade done ok?

TC-RECV version is 2.4.4 B 200511221336682
ETOKEN firmware version is 4.2.5.4
TechniSat DVB-PC TV Star PCI driver version is 4.3.2.9999

Thanks

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N� 30666121 *****
*** 2nd e-mail: vimone@ ***
***************************************







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links











Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links









Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links









--
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.1.392 / Virus Database: 268.5.6/340 - Release Date: 15/05/2006


Re: Looking at the logs...

Ulrich G. Kliegis
 

On 20 May 2006 at 12:32, nigel heasman wrote:

Just a thought - do I remember you saying you had
connected the EKU (dongle) through an extension lead?
If so, that might be the problem as I am sure I've
heard of other folk who tried this, so they could see
it and getting similar errors.
Hi Nigel,

thanks for the thought, but nope, that's not me, my dongle lives in its
proper place all the time, NPI :)

Regards,
U.


Re: Looking at the logs...

nigel heasman <nigel_heasman@...>
 

--- "Ulrich G. Kliegis" <Ulrich.Kliegis@kliegis.de>
wrote:
---------------------------------
....Maybe it will boil down to one - a problem with or
in the dongle.....
-----------------------------------
Hi Ulrich,
Just a thought - do I remember you saying you had
connected the EKU (dongle) through an extension lead?
If so, that might be the problem as I am sure I've
heard of other folk who tried this, so they could see
it and getting similar errors.
good luck
Nigel


Re: Looking at the logs...

Ulrich G. Kliegis
 

On 19 May 2006 at 21:36, a_van_belle wrote:

Hello Ulrich,

You must be hit by two problems I guess.
Maybe it will boil down to one - a problem with or in the dongle. After
the communication last night I first reinstalled the rt3.51 program, then
ran the tests described in the eumetcast FAQs. It looked like the
dongle is ok, the license information in the tellicast suite looks good
too.
Then I let the eumetcast frontend collect some data in &#92;received before
starting MDM. Disappointingly, the same behaviour: The images that
had collected until the start of MDM were all decoded and stored
correctly, but everything coming after that just caused the yellow REC
''LED' to light up, but was neither decoded nor stored.

Since it was after 0000 local time in the meantime, I decided to catch
some sleep, but looked at the log file (in the t-systems folder) again.
Here is the bottom part of it:


ERR:2006-05-19 22:03:36.563:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 7465.
ERR:2006-05-19 22:03:37.374:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 7466.
ERR:2006-05-19 22:03:40.499:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 7466.
ERR:2006-05-19 22:03:41.871:Cannot join channel "EUMETSAT Data
Channel 5": Failed to decode key 7469.
ERR:2006-05-19 22:03:44.104:Cannot join channel "EUMETSAT Data
Channel 5": Failed to decode key 7469.
ERR:2006-05-19 22:03:52.656:Cannot join channel "SAF-Europe":
Failed to decode key 7471.
ERR:2006-05-19 22:03:59.276:Cannot join channel "SAF-Europe":
Failed to decode key 7471.
ERR:2006-05-19 22:04:00.197:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 7474.
ERR:2006-05-19 22:04:12.936:eToken transaction timed out
ERR:2006-05-19 22:04:12.936:Critical dongle error (eToken
transaction timed out). Restarting child.

At that time, the dongle - LED was dark.

Today, I decided to separate the steps to come closer to some an
analysis. So, I modified the rec.ini and rec-channels.ini to collect the
received files on that big 250 G HDD. It fills continuously now with data.
Whenever a set of files is written to &#92;received, the dongle LED gets
dark for a moment. Is that normal? It never occurred to me before
when the system was still running on that other hardware.

Anyway, if the data collected in &#92;received, the eumetcast part of the
receiving side can be regarded as working at least for that phase,
where no interaction takes place with other software. Unfortunately,
David seems to be out for some time. So, it's a bit like walking in thick
fog... But at least, this is what it's all about, ins't it? :)

Regards,
U.



Firstly "cannot join.." looks like a password related problem.
Make sure you have all characters correct (Spot the difference between
l1I O0 ?)
Oh, I am familiar with such. 20 years ago, i spent some nights finding
an 0 instead of an O in an assembler source text (about 2 kg of
paper...) - that has taught me some lessons... :) But it still can happen,
and no, no potential for a mixup, and the tellicast suite regards it as
correct as well.


and if you edited the password in the ini file make sure you
have a line "user_key=" and not "user_key_crypt="
I edited the ini file, but did not touch the password. On the previous PC,
that ini file survived some other treatment as well, with the crypted part
untouched. I use MS Editor, so there should also ne no potential for
foreign text matter to intrude...

Make sure MDM is setup to MSG1 or MSG2, if "Delete other" is selected,
data from the "unselected MSG" will be deleted instantly.
I double and cross checked that. Also ran the same procedure for
MSG-2 data for some time, same result.


Good luck,
Thanks.

I still can test on a third machine to rule outr faulty hardware on that
new (old) 'pooter. Some other errands are on my personal (and my
wife's :) ) list to be done too...


Tschüß, cheers, ciao (what's it in dutch?)

U.


Re: About

a_van_belle
 

Sorry about the mixup Ian,

I did not read correctly and somewhere in my mind the two names got
mixed up. Guess I need a new memory module too !

Greetings,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Ian Deans" <isdeans1.-_@...> wrote:

Arne that mail actually came from me (Ian) not Douglas as did the
mail re
the ERS-SCAT trial on 17/5/06 where you replied in error to Douglas
as well.
Sorry for the confusion but we are identical twins so maybe our
mails are as
similar as our voices !!!!!

Regards
Ian ( I think !!! )


----- Original Message -----
From: "a_van_belle" <a.van.belle@...>
To: <MSG-1@yahoogroups.com>
Sent: Friday, May 19, 2006 10:25 PM
Subject: R: [MSG-1] Re: About



As Douglas mentioned newer versions are available and these might work
perfectly but are not the recommended/tested one.


R: Re: About

a_van_belle
 

Sorry to hear about yout problems Vincenzo,

If you cannot receive now due to a partly removed driver I suggest you
try to install the skystar version 4.3.0 over the old one.

But if all still works you better stick to 4.2.2, as mentioned before
there is nothing wrong with this driver.

Good luck,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@...> wrote:

Hi Arne,
nothing to do i've tried how you suggested me
in safe mode but I have the same result.
When I click on it to uninstall, I get and orange page with a
warning which ask me if I want to remove completely the application.
I click on OK so I get another small blue window with a bar but after a
couple of seconds it disappear and remains only the orange page and
after a couple of seconds even the orange page disappears and the
application is still in the add/remove programs.
Any other suggestion?


73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@... ***
***************************************
-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per conto di
a_van_belle
Inviato: sabato 20 maggio 2006 0.12
A: MSG-1@yahoogroups.com
Oggetto: R: [MSG-1] Re: About

Hi Vincenzo,

May be there is still a program running or you do not have sufficient
privileges (can occur on XP).
If all fails retry in safe mode.

Good luck,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@> wrote:

Hi Arne,
The PDF says:

1. Exit the Tellicast client and Server4Pc programs
(right-click on the icons in the tray and exit)
2. Completely uninstall any existing Technisat DVB software:
- Go to Control "Panel - Add or Remove Programs" and
- select "Technisat DVB Receiver" or similar.
- If asked to "Remove shared file", select "No to All"
I done it but it does not uninstall it.
When I click on it to uninstall, I get and orange page with a
warning which
ask me if I want to remove completely the application.
I click on OK so I get another small blue window with a bar but
after a
couple of seconds it disappear and remains only the orange page and
after a
couple of seconds even the orange page disappears and the
application is
still in the add/remove programs.
Why this?
What happens?
Thanks







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links




Re: I confess... I confess

Lawrence <lawrence@...>
 

Thanks guys - Giuseppe and Arne (and possibly others). After doing the minor mods all is well. I haven't yet run the update but at least everything is running again and I have the files.

Lawrence


Re: About

Ian Deans <isdeans1.-_@...>
 

Arne that mail actually came from me (Ian) not Douglas as did the mail re the ERS-SCAT trial on 17/5/06 where you replied in error to Douglas as well. Sorry for the confusion but we are identical twins so maybe our mails are as similar as our voices !!!!!

Regards
Ian ( I think !!! )

----- Original Message -----
From: "a_van_belle" <a.van.belle@hccnet.nl>
To: <MSG-1@yahoogroups.com>
Sent: Friday, May 19, 2006 10:25 PM
Subject: R: [MSG-1] Re: About



As Douglas mentioned newer versions are available and these might work
perfectly but are not the recommended/tested one.


R: Re: About

Vincenzo Mone
 

Hi Arne,
nothing to do i've tried how you suggested me
in safe mode but I have the same result.
When I click on it to uninstall, I get and orange page with a
warning which ask me if I want to remove completely the application.
I click on OK so I get another small blue window with a bar but after a
couple of seconds it disappear and remains only the orange page and
after a couple of seconds even the orange page disappears and the
application is still in the add/remove programs.
Any other suggestion?


73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@tin.it ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per conto di
a_van_belle
Inviato: sabato 20 maggio 2006 0.12
A: MSG-1@yahoogroups.com
Oggetto: R: [MSG-1] Re: About

Hi Vincenzo,

May be there is still a program running or you do not have sufficient
privileges (can occur on XP).
If all fails retry in safe mode.

Good luck,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@...> wrote:

Hi Arne,
The PDF says:

1. Exit the Tellicast client and Server4Pc programs
(right-click on the icons in the tray and exit)
2. Completely uninstall any existing Technisat DVB software:
- Go to Control "Panel - Add or Remove Programs" and
- select "Technisat DVB Receiver" or similar.
- If asked to "Remove shared file", select "No to All"
I done it but it does not uninstall it.
When I click on it to uninstall, I get and orange page with a
warning which
ask me if I want to remove completely the application.
I click on OK so I get another small blue window with a bar but after a
couple of seconds it disappear and remains only the orange page and
after a
couple of seconds even the orange page disappears and the application is
still in the add/remove programs.
Why this?
What happens?
Thanks







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links




Re: Looking at the logs...

Giuseppe Cico
 

I'm running RTE 3.65 from last updates, but I've had this problem firstly
on tuesday, with old version... and I use XP/SP2 that's currently updated.
So this seems not the problem... it's 20 minutes that all is running just
moving EKU from back of PC to a USB cable... maybe it's a temperature
problem...
Really it's crazy... but now it seems working...
Ciao
Giuseppe

What version of eToken Run Time Environtment do you use ?

RTE 3.65 readme tells me that Windows 2000 SP4 or higher is required.
On my regular receive PC I have W2k SP3 but still run RTE3.51 as
supplied on CDROM V4 !

Try to upgrade to SP4 or downgrade to RTE3.51 and TC240

Good luck,
Arne van Belle



--- In MSG-1@yahoogroups.com, "Giuseppe Cico" wrote:
>
> Arne and Ulrich,
> same problem here... have tested EKU according to FAQs...
> Removing and reconnecting EKU makes system working and "USER
PRESENT..."
> Seems like a EKU failure... ????
> Tomorrow I'll test... but it's strange that also Ulrich has same
problem...
> Ciao
> Giuseppe







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm





SPONSORED LINKS
Computer science Science
education Weather equipment

Weather stations
YAHOO! GROUPS LINKS
Visit your group "MSG-1" on the web.
To unsubscribe from this group, send an email to:
MSG-1-unsubscribe@yahoogroups.com
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


R: Re: About

a_van_belle
 

Hi Vincenzo,

May be there is still a program running or you do not have sufficient
privileges (can occur on XP).
If all fails retry in safe mode.

Good luck,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@...> wrote:

Hi Arne,
The PDF says:

1. Exit the Tellicast client and Server4Pc programs
(right-click on the icons in the tray and exit)
2. Completely uninstall any existing Technisat DVB software:
- Go to Control "Panel - Add or Remove Programs" and
- select "Technisat DVB Receiver" or similar.
- If asked to "Remove shared file", select "No to All"
I done it but it does not uninstall it.
When I click on it to uninstall, I get and orange page with a
warning which
ask me if I want to remove completely the application.
I click on OK so I get another small blue window with a bar but after a
couple of seconds it disappear and remains only the orange page and
after a
couple of seconds even the orange page disappears and the application is
still in the add/remove programs.
Why this?
What happens?
Thanks


Re: Looking at the logs...

a_van_belle
 

What version of eToken Run Time Environtment do you use ?

RTE 3.65 readme tells me that Windows 2000 SP4 or higher is required.
On my regular receive PC I have W2k SP3 but still run RTE3.51 as
supplied on CDROM V4 !

Try to upgrade to SP4 or downgrade to RTE3.51 and TC240

Good luck,
Arne van Belle



--- In MSG-1@yahoogroups.com, "Giuseppe Cico" <giuseppe.cico@...> wrote:

Arne and Ulrich,
same problem here... have tested EKU according to FAQs...
Removing and reconnecting EKU makes system working and "USER PRESENT..."
Seems like a EKU failure... ????
Tomorrow I'll test... but it's strange that also Ulrich has same
problem...
Ciao
Giuseppe


R: Re: About

Vincenzo Mone
 

Hi Arne,
The PDF says:

1. Exit the Tellicast client and Server4Pc programs
(right-click on the icons in the tray and exit)
2. Completely uninstall any existing Technisat DVB software:
- Go to Control "Panel - Add or Remove Programs" and
- select "Technisat DVB Receiver" or similar.
- If asked to "Remove shared file", select "No to All"
I done it but it does not uninstall it.
When I click on it to uninstall, I get and orange page with a warning which
ask me if I want to remove completely the application.
I click on OK so I get another small blue window with a bar but after a
couple of seconds it disappear and remains only the orange page and after a
couple of seconds even the orange page disappears and the application is
still in the add/remove programs.
Why this?
What happens?
Thanks




73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@tin.it ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per conto di
a_van_belle
Inviato: venerdì 19 maggio 2006 23.44
A: MSG-1@yahoogroups.com
Oggetto: R: [MSG-1] Re: About

Hi Vincenzo,

Version 4.2.2 was the recommended one before 4.3.0 and never gave me
any problems.
If all works I would not change it.

A detailed upgrade installation guide is included in the Update you
received from Eumetsat. Goto folder Windows&#92;Skystar_4_3_0_a and open
readme_skystar_xp_v2.pdf (or the w2k version of you use windows2000)

Greetings,
Arne van Belle
--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@...> wrote:

Hi Arne,
I have checked the Skystar/Technisat driver
and have all Version 4.2.2.
Do I need to upgrade it?
If yes which is the procedure.
The eToken in the "Add/Remove programs" is "eToken Run Time Environment
3.65"
Thanks again.


73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@... ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per conto di
a_van_belle
Inviato: venerdì 19 maggio 2006 23.25
A: MSG-1@yahoogroups.com
Oggetto: R: [MSG-1] Re: About

Hello Vincenzo,

You probably did the update correctly. But with so many version
numbers it can be confusing.

Eumetsat's update consists of the Skystar/Technisat driver, which most
of us don't need to update as the same version was already included on
the EUMETCast Client Software V4 CDROM.
To check this Rightclick the (hopefully) green Sat Icon in the tray
and choose "About DVB Receiver"
This should list Version 4.3.0 for all instances.

As Douglas mentioned newer versions are available and these might work
perfectly but are not the recommended/tested one.

To check if the recommended EKU-software has been installed correctly,
look in "Add/Remove programs" for "eToken Run Time Environment 3.65"

The Tellicast version is shown in the uppermost "About tc-recv" and
should read 2.4.4 B .......

Greetings,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@> wrote:

Hi Arne,
what do you mean with:
The telecast version you mention is correct.
4.2.5.4 is the firmware in your EKU, this was not updated.
You mean I did not update it or Eumetsat did not send the update?
Thanks

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@ ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per
conto di
a_van_belle
Inviato: venerdì 19 maggio 2006 22.29
A: MSG-1@yahoogroups.com
Oggetto: [MSG-1] Re: About

Hello Vincenzo,

The double "About" is a minor problem in the new Tellicast
client that
has been reported to Eumetsat already.

The tellicast version you mention is correct.
4.2.5.4 is the firmware in your EKU, this was not updated,
only the
eToken RunTimeEnvironment is updated from 3.51 to 3.65 but it
is not
easy to check this.

Are you sure about TechniSat driver version 4.3.2.9999 ??
The version in EUMETSAT's update is 4.3.0.9999
But if it works, don't fix it !

Greetings,
Arne van Belle


--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@> wrote:

Hi to the list,
after several trials I have done the upgrades.
Now I have noticed that if I right click on the T in the taskbar
Compares two times the words ABOUT TC-RECV.
If I click on the top one I get the information's but If I click
on the
bottom one, nothing happens.
Has anybody noticed it?
Is it normal?
Please are the upgrade done ok?

TC-RECV version is 2.4.4 B 200511221336682
ETOKEN firmware version is 4.2.5.4
TechniSat DVB-PC TV Star PCI driver version is 4.3.2.9999

Thanks

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@ ***
***************************************







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links











Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links









Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links




Re: Looking at the logs...

Giuseppe Cico
 

Arne and Ulrich,
same problem here... have tested EKU according to FAQs...
Removing and reconnecting EKU makes system working and "USER PRESENT..."
Seems like a EKU failure... ????
Tomorrow I'll test... but it's strange that also Ulrich has same problem...
Ciao
Giuseppe

Hello Ulrich,

You must be hit by two problems I guess.
Firstly "cannot join.." looks like a password related problem.
Make sure you have all characters correct (Spot the difference between
l1I O0 ?) and if you edited the password in the ini file make sure you
have a line "user_key=" and not "user_key_crypt="

Make sure MDM is setup to MSG1 or MSG2, if "Delete other" is
selected,
data from the "unselected MSG" will be deleted instantly.

Good luck,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Ulrich G. Kliegis"
wrote:
>
> ... can be helpful.
> In short: I took my preliminary receiver-computer apart and put a new
> machine together. More speed (800 vs. 500 Mhz), more memory (1 G
> vs. 768 M), more disk space (250+40 vs. 40 alone). Win2k, brought to
> the latest SP state. Reinstalled Technisat drivers, server4PC is
> running, Tellique (the well know version), EKU-driver. The dongle-LED
> is on, green dot, pink T. RAMDISK 128 MB, rec-channels.ini and rec.ini
> set correctly, received-directory fills with MSG-1 files.
> Installed MSG-DM (evaluation license for the latest version, 28 days to
> go) and AVHRR-M (test license from David), set the directories, hit
> start. MSG-DM processes the files present in the received-directory,
> deletes them afterwards, the images are stored in the correct place.
>
> So faaaaar, so gooooooood.
>
> Now waiting for the next set of scans. Waiting. Waiting. The yellow
> REC-pseudo-LED comes on, but no 'processing ...'. And no new
> images in the HRIT etc. dirs. Checked the registry, nothing unexpected.
> AVHRR-M lists all the passes for al stations (all checked). But no
> processing (of course only those from the canaries). And still nothing
> from MSG-1. Changed the whole thing (including rec-channels.ini) to
> receive MSG-2. When the green 'LED' in MSG-DM is off, the received-
> dir fills with the usual files, but when I set it to 'run' (hitting
start), it
> empties the received-dir, but does not process them (difference to
> starting MSG-DM after received has collected some files).
>
> Now, back to the subject line, a look into th elog files reveals this:
>
> (excerpt, there are tons of this)
>
>
> ERR:2006-05-19 17:49:40.514:Cannot join channel "EUMETSAT Data
Channel 1": Failed to decode key 4140.
> ERR:2006-05-19 17:49:42.147:Cannot join channel "EUMETSAT Data
Channel 1": Failed to decode key 4140.
> ERR:2006-05-19 17:49:48.265:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 4116.
> ERR:2006-05-19 17:49:54.424:Cannot join channel "EUMETSAT Data
Channel 5": Failed to decode key 4122.
> ERR:2006-05-19 17:50:10.137:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 4144.
> ERR:2006-05-19 17:50:11.098:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 4144.
> ERR:2006-05-19 17:50:18.869:Cannot join channel "EUMETSAT Data
Channel 2": Missing key 4145.
> ERR:2006-05-19 17:50:20.211:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 4146.
> ERR:2006-05-19 17:50:20.402:Cannot join channel "EUMETSAT Data
Channel 6": Failed to decode key 4147.
> ERR:2006-05-19 17:50:22.164:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 4146.
> ERR:2006-05-19 17:50:24.167:Cannot join channel "EUMETSAT Data
Channel 6": Failed to decode key 4147.
> ERR:2006-05-19 17:50:28.183:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 4148.
> ERR:2006-05-19 17:50:30.987:Cannot join channel "EUMETSAT Data
Channel 3": Missing key 4148.
>
>
>
>
> Yes, I read the EUMETCAST-FAQs on missing key-symptoms. What
> puzzles me is the fact that the files do arrive in the received
directory
> but can't be decoded then. I'll do the tests recommended by Eumetsat
> now, but the mystery remains. Is it one?
>
> Any comments?
>
> Cheers, ciao, tsch��,
>
> U.
>
>
>
>
>







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm





SPONSORED LINKS
Weather equipment
Computer science Science
education
Weather stations
YAHOO! GROUPS LINKS
Visit your group "MSG-1" on the web.
To unsubscribe from this group, send an email to:
MSG-1-unsubscribe@yahoogroups.com
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


Re: About

a_van_belle
 

Hello Robert,

If you do not receive DWDsat or MSG2 trial data and do not plan to
receive the future METOP data, your current configuration most likely
won't need updating.

The only problem we currently have is that every Update send over
EUMETCast (twice a day up to May 31) will disrupt Tellicast if you run
it on a ramdisk smaller than 40 Mb.

If you do encounter unexpected data loss after May 30 then update the
EKU software (to version 3.65) and the Tellicast client (to 2.44).

Greetings,
Arne van Belle

--- In MSG-1@yahoogroups.com, Robert Moore <rsmoore@...> wrote:

Arne I now belong to the '.. if it works, don't fix it' school of
thought.
So if everything is currently working OK what are minimum changes I
need to
make using the update files? Just EKU software?

Robert


R: Re: About

a_van_belle
 

Hi Vincenzo,

Version 4.2.2 was the recommended one before 4.3.0 and never gave me
any problems.
If all works I would not change it.

A detailed upgrade installation guide is included in the Update you
received from Eumetsat. Goto folder Windows&#92;Skystar_4_3_0_a and open
readme_skystar_xp_v2.pdf (or the w2k version of you use windows2000)

Greetings,
Arne van Belle
--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@...> wrote:

Hi Arne,
I have checked the Skystar/Technisat driver
and have all Version 4.2.2.
Do I need to upgrade it?
If yes which is the procedure.
The eToken in the "Add/Remove programs" is "eToken Run Time Environment
3.65"
Thanks again.


73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@... ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per conto di
a_van_belle
Inviato: venerdì 19 maggio 2006 23.25
A: MSG-1@yahoogroups.com
Oggetto: R: [MSG-1] Re: About

Hello Vincenzo,

You probably did the update correctly. But with so many version
numbers it can be confusing.

Eumetsat's update consists of the Skystar/Technisat driver, which most
of us don't need to update as the same version was already included on
the EUMETCast Client Software V4 CDROM.
To check this Rightclick the (hopefully) green Sat Icon in the tray
and choose "About DVB Receiver"
This should list Version 4.3.0 for all instances.

As Douglas mentioned newer versions are available and these might work
perfectly but are not the recommended/tested one.

To check if the recommended EKU-software has been installed correctly,
look in "Add/Remove programs" for "eToken Run Time Environment 3.65"

The Tellicast version is shown in the uppermost "About tc-recv" and
should read 2.4.4 B .......

Greetings,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@> wrote:

Hi Arne,
what do you mean with:
The telecast version you mention is correct.
4.2.5.4 is the firmware in your EKU, this was not updated.
You mean I did not update it or Eumetsat did not send the update?
Thanks

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@ ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per
conto di
a_van_belle
Inviato: venerdì 19 maggio 2006 22.29
A: MSG-1@yahoogroups.com
Oggetto: [MSG-1] Re: About

Hello Vincenzo,

The double "About" is a minor problem in the new Tellicast
client that
has been reported to Eumetsat already.

The tellicast version you mention is correct.
4.2.5.4 is the firmware in your EKU, this was not updated,
only the
eToken RunTimeEnvironment is updated from 3.51 to 3.65 but it
is not
easy to check this.

Are you sure about TechniSat driver version 4.3.2.9999 ??
The version in EUMETSAT's update is 4.3.0.9999
But if it works, don't fix it !

Greetings,
Arne van Belle


--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@> wrote:

Hi to the list,
after several trials I have done the upgrades.
Now I have noticed that if I right click on the T in the taskbar
Compares two times the words ABOUT TC-RECV.
If I click on the top one I get the information's but If I click
on the
bottom one, nothing happens.
Has anybody noticed it?
Is it normal?
Please are the upgrade done ok?

TC-RECV version is 2.4.4 B 200511221336682
ETOKEN firmware version is 4.2.5.4
TechniSat DVB-PC TV Star PCI driver version is 4.3.2.9999

Thanks

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@ ***
***************************************







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links











Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links




Re: Looking at the logs...

a_van_belle
 

Hello Ulrich,

You must be hit by two problems I guess.
Firstly "cannot join.." looks like a password related problem.
Make sure you have all characters correct (Spot the difference between
l1I O0 ?) and if you edited the password in the ini file make sure you
have a line "user_key=" and not "user_key_crypt="

Make sure MDM is setup to MSG1 or MSG2, if "Delete other" is selected,
data from the "unselected MSG" will be deleted instantly.

Good luck,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Ulrich G. Kliegis" <Ulrich.Kliegis@...>
wrote:

... can be helpful.
In short: I took my preliminary receiver-computer apart and put a new
machine together. More speed (800 vs. 500 Mhz), more memory (1 G
vs. 768 M), more disk space (250+40 vs. 40 alone). Win2k, brought to
the latest SP state. Reinstalled Technisat drivers, server4PC is
running, Tellique (the well know version), EKU-driver. The dongle-LED
is on, green dot, pink T. RAMDISK 128 MB, rec-channels.ini and rec.ini
set correctly, received-directory fills with MSG-1 files.
Installed MSG-DM (evaluation license for the latest version, 28 days to
go) and AVHRR-M (test license from David), set the directories, hit
start. MSG-DM processes the files present in the received-directory,
deletes them afterwards, the images are stored in the correct place.

So faaaaar, so gooooooood.

Now waiting for the next set of scans. Waiting. Waiting. The yellow
REC-pseudo-LED comes on, but no 'processing ...'. And no new
images in the HRIT etc. dirs. Checked the registry, nothing unexpected.
AVHRR-M lists all the passes for al stations (all checked). But no
processing (of course only those from the canaries). And still nothing
from MSG-1. Changed the whole thing (including rec-channels.ini) to
receive MSG-2. When the green 'LED' in MSG-DM is off, the received-
dir fills with the usual files, but when I set it to 'run' (hitting
start), it
empties the received-dir, but does not process them (difference to
starting MSG-DM after received has collected some files).

Now, back to the subject line, a look into th elog files reveals this:

(excerpt, there are tons of this)


ERR:2006-05-19 17:49:40.514:Cannot join channel "EUMETSAT Data
Channel 1": Failed to decode key 4140.
ERR:2006-05-19 17:49:42.147:Cannot join channel "EUMETSAT Data
Channel 1": Failed to decode key 4140.
ERR:2006-05-19 17:49:48.265:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 4116.
ERR:2006-05-19 17:49:54.424:Cannot join channel "EUMETSAT Data
Channel 5": Failed to decode key 4122.
ERR:2006-05-19 17:50:10.137:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 4144.
ERR:2006-05-19 17:50:11.098:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 4144.
ERR:2006-05-19 17:50:18.869:Cannot join channel "EUMETSAT Data
Channel 2": Missing key 4145.
ERR:2006-05-19 17:50:20.211:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 4146.
ERR:2006-05-19 17:50:20.402:Cannot join channel "EUMETSAT Data
Channel 6": Failed to decode key 4147.
ERR:2006-05-19 17:50:22.164:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 4146.
ERR:2006-05-19 17:50:24.167:Cannot join channel "EUMETSAT Data
Channel 6": Failed to decode key 4147.
ERR:2006-05-19 17:50:28.183:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 4148.
ERR:2006-05-19 17:50:30.987:Cannot join channel "EUMETSAT Data
Channel 3": Missing key 4148.




Yes, I read the EUMETCAST-FAQs on missing key-symptoms. What
puzzles me is the fact that the files do arrive in the received
directory
but can't be decoded then. I'll do the tests recommended by Eumetsat
now, but the mystery remains. Is it one?

Any comments?

Cheers, ciao, tschüß,

U.



[Non-text portions of this message have been removed]


R: Re: About

Vincenzo Mone
 

Hi Arne,
I have checked the Skystar/Technisat driver
and have all Version 4.2.2.
Do I need to upgrade it?
If yes which is the procedure.
The eToken in the "Add/Remove programs" is "eToken Run Time Environment
3.65"
Thanks again.


73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@tin.it ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per conto di
a_van_belle
Inviato: venerdì 19 maggio 2006 23.25
A: MSG-1@yahoogroups.com
Oggetto: R: [MSG-1] Re: About

Hello Vincenzo,

You probably did the update correctly. But with so many version
numbers it can be confusing.

Eumetsat's update consists of the Skystar/Technisat driver, which most
of us don't need to update as the same version was already included on
the EUMETCast Client Software V4 CDROM.
To check this Rightclick the (hopefully) green Sat Icon in the tray
and choose "About DVB Receiver"
This should list Version 4.3.0 for all instances.

As Douglas mentioned newer versions are available and these might work
perfectly but are not the recommended/tested one.

To check if the recommended EKU-software has been installed correctly,
look in "Add/Remove programs" for "eToken Run Time Environment 3.65"

The Tellicast version is shown in the uppermost "About tc-recv" and
should read 2.4.4 B .......

Greetings,
Arne van Belle

--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@...> wrote:

Hi Arne,
what do you mean with:
The telecast version you mention is correct.
4.2.5.4 is the firmware in your EKU, this was not updated.
You mean I did not update it or Eumetsat did not send the update?
Thanks

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@... ***
***************************************

-----Messaggio originale-----
Da: MSG-1@yahoogroups.com [mailto:MSG-1@yahoogroups.com] Per conto di
a_van_belle
Inviato: venerdì 19 maggio 2006 22.29
A: MSG-1@yahoogroups.com
Oggetto: [MSG-1] Re: About

Hello Vincenzo,

The double "About" is a minor problem in the new Tellicast client that
has been reported to Eumetsat already.

The tellicast version you mention is correct.
4.2.5.4 is the firmware in your EKU, this was not updated, only the
eToken RunTimeEnvironment is updated from 3.51 to 3.65 but it is not
easy to check this.

Are you sure about TechniSat driver version 4.3.2.9999 ??
The version in EUMETSAT's update is 4.3.0.9999
But if it works, don't fix it !

Greetings,
Arne van Belle


--- In MSG-1@yahoogroups.com, "Vincenzo Mone" <vimone@> wrote:

Hi to the list,
after several trials I have done the upgrades.
Now I have noticed that if I right click on the T in the taskbar
Compares two times the words ABOUT TC-RECV.
If I click on the top one I get the information's but If I click
on the
bottom one, nothing happens.
Has anybody noticed it?
Is it normal?
Please are the upgrade done ok?

TC-RECV version is 2.4.4 B 200511221336682
ETOKEN firmware version is 4.2.5.4
TechniSat DVB-PC TV Star PCI driver version is 4.3.2.9999

Thanks

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




***************************************

***** GSM +39 338 9749786 *****
***** SMS +39 338 9749786 *****
***** FAX +39 328 7244294 *****
***** ICQ N° 30666121 *****
*** 2nd e-mail: vimone@ ***
***************************************







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links











Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm


Yahoo! Groups Links




Re: Looking at the logs...

Giuseppe Cico
 

Ulrich, I'm going crazy today.... I've lots of "Failed to decode" and
"missing key" too...
I saw them in past days, so it's not due to updates...
I tried removing ramdisk and decoding to hd... no change...
I'm going to sleep... hoping tomorrow I wake up with a successfull idea...
Ciao
Giuseppe

... can be helpful.
In short: I took my preliminary receiver-computer apart and put a new
machine together. More speed (800 vs. 500 Mhz), more memory (1 G
vs. 768 M), more disk space (250+40 vs. 40 alone). Win2k, brought to
the latest SP state. Reinstalled Technisat drivers, server4PC is
running, Tellique (the well know version), EKU-driver. The dongle-LED
is on, green dot, pink T. RAMDISK 128 MB, rec-channels.ini and rec.ini
set correctly, received-directory fills with MSG-1 files.
Installed MSG-DM (evaluation license for the latest version, 28 days to
go) and AVHRR-M (test license from David), set the directories, hit
start. MSG-DM processes the files present in the received-directory,
deletes them afterwards, the images are stored in the correct place.

So faaaaar, so gooooooood.

Now waiting for the next set of scans. Waiting. Waiting. The yellow
REC-pseudo-LED comes on, but no 'processing ...'. And no new
images in the HRIT etc. dirs. Checked the registry, nothing unexpected.
AVHRR-M lists all the passes for al stations (all checked). But no
processing (of course only those from the canaries). And still nothing
from MSG-1. Changed the whole thing (including rec-channels.ini) to
receive MSG-2. When the green 'LED' in MSG-DM is off, the received-
dir fills with the usual files, but when I set it to 'run' (hitting
start), it
empties the received-dir, but does not process them (difference to
starting MSG-DM after received has collected some files).

Now, back to the subject line, a look into th elog files reveals this:

(excerpt, there are tons of this)


ERR:2006-05-19 17:49:40.514:Cannot join channel "EUMETSAT Data
Channel 1": Failed to decode key 4140.
ERR:2006-05-19 17:49:42.147:Cannot join channel "EUMETSAT Data
Channel 1": Failed to decode key 4140.
ERR:2006-05-19 17:49:48.265:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 4116.
ERR:2006-05-19 17:49:54.424:Cannot join channel "EUMETSAT Data
Channel 5": Failed to decode key 4122.
ERR:2006-05-19 17:50:10.137:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 4144.
ERR:2006-05-19 17:50:11.098:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 4144.
ERR:2006-05-19 17:50:18.869:Cannot join channel "EUMETSAT Data
Channel 2": Missing key 4145.
ERR:2006-05-19 17:50:20.211:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 4146.
ERR:2006-05-19 17:50:20.402:Cannot join channel "EUMETSAT Data
Channel 6": Failed to decode key 4147.
ERR:2006-05-19 17:50:22.164:Cannot join channel "EUMETSAT Data
Channel 2": Failed to decode key 4146.
ERR:2006-05-19 17:50:24.167:Cannot join channel "EUMETSAT Data
Channel 6": Failed to decode key 4147.
ERR:2006-05-19 17:50:28.183:Cannot join channel "EUMETSAT Data
Channel 3": Failed to decode key 4148.
ERR:2006-05-19 17:50:30.987:Cannot join channel "EUMETSAT Data
Channel 3": Missing key 4148.




Yes, I read the EUMETCAST-FAQs on missing key-symptoms. What
puzzles me is the fact that the files do arrive in the received directory
but can't be decoded then. I'll do the tests recommended by Eumetsat
now, but the mystery remains. Is it one?

Any comments?

Cheers, ciao, tsch��,

U.







Unsure what a term means? Check the Glossary at:
http://www.david-taylor.myby.co.uk/wxsat/glossary.htm





SPONSORED LINKS
Computer science Weather
equipment Science education

Weather stations
YAHOO! GROUPS LINKS
Visit your group "MSG-1" on the web.
To unsubscribe from this group, send an email to:
MSG-1-unsubscribe@yahoogroups.com
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.