In fact I've problems with HVS-1

Hi, I am using a TBS 5927 (1 month) it works OK, at least with the Basic service, the driver version I have is 1.0.0.7 downloaded from the TBS site. Regards Youssef Bennouna ETUDES ET MESURES LES 5

I always have a lot of missing packets, even with an snr of 13.1dB. Following.

Can anyone who is using the TBS 5927 successfully on Windows 10 and by that I mean no losses or missed/recovered packets from their end please advise which TBS driver they are using. Regards Ian.

Youssef, with the low SNR you have even Basic Service is impaired by non working HVS-1. You should get far less missed Basic packets if you set the MODCOD filter 8PSK 3/5 for Basic Service only. Of

Thank you very much Ernst, So it seems that my LM is ~ 3.1-3.5 for basic service and almost 0 dB for HVs-1, less than what Eumetsat recommends but it works for basic. The first thing to do; enhance

Youssef, I never had a Windows receiver. If TBS IP-Tool works for you stay with it. A couple of people including David have reported "Blue Screens Of Death" (BSODs) with TBS IP-Tool and have changed

Youssef, with SNR 9.0 - 9.5dB you cannot receive HVS-1. EUMETSAT says you should have 4dB link margin (LM) for good reception. LM depends on SNR and MODCOD used. I apply these formulas in my

Hello Ernst, Yes, I am using TBS-IP Tool. Concerning the SNR, I think it’s less, usually around 9-9.5 according to the TBS interface. Concerning the MOCODEs, I selected all the modes to avoid any

Hi Youssef Do you use TBS IP-Tool or CrazyCat's BDA-DataEx? Do you have enough SNR (it shoud be 12dB or above for HVS-1)? Are you sure you have no MODCOD filter set (that prevents HVS-1 trafic to get

Hello everybody, I am trying to get data through TSL-HVS1 but the tellicast stays in the "connecting" state. I receive data through Basic service normally. I checked the *.ini files, I also compared

Hi I hope someone can help as ive forgotten how to resolve this problem On starting tellicast hvs-2 i have a red icon bottom right of screen Checking the log file it seems to be something to do with

Hi No one here has AFAIK used Zabbix that seems to be an overkill for monitoring EUMETCast receivers. Windows users with TC monitoring have MRTG running and there is much documentation on Davids site.

Hello! I have one question to be discussed: How it will increase EumetCast SAT server working processes if I will add on it Zabbix monitoring systems agent2 (it could be 2 types: active or passive

Hi I was wondering why my signal was getting stronger. I was usually getting 11.3db and now its at 12.3db Hope it keeps like that Sent from Mail for Windows 10

Ian, Just logged on to my email's and I was about to comment on this first and then saw you post. Yes, I'm afraid 'someone was obviously listening?' We should have kept quiet and hoped 'the powers

Spoke too soon John, as sometime earlier today the increased signal I had been seeing vanished and signal levels back to where they were. Unfortunate as I need all the signal I can get up

Hi Daniele, No it is not possible in the current release, but I am sure that you can do that in Gimp or Photoshop .... Grts, Hugo

Hello Ian, Good to hear you are seeing and improved signal up there in Scotland. I should have said that my SR1 Power reading remains at - 25 dBm 'despite' the increased SNR. My SNR was steady at

============================================================= John I am seeing an increase in signal since yesterday as well, up about 0.3 SNR. When others reported a signal increase recently, I had