Date   

Re: Configuration File

Vincenzo Mone
 

Thanks David,
but apologise I did not understood what you mean?
I have just one Ethernet lead and to send the cfg file to the SR1 I will use the USB Port.
I hope is this what you mean.
So finally which is the correct cfg file to use?
Thanks in advance

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




*********************************
****** GSM +39 328 7110193 ******
***** SMS +39 328 7110193 *****
*********************************

-----Messaggio originale-----
Da: MSG-1@groups.io <MSG-1@groups.io> Per conto di David J Taylor
GM8ARV ?????????????? ???? via groups.io
Inviato: mercoledì 18 agosto 2021 12:51
A: MSG-1@groups.io
Oggetto: Re: [MSG-1] Configuration File

On 18/08/2021 10:57, Vincenzo Mone wrote:
Hello to the list,

Thanks to David, I have sent an email to Eumetsat asking for the
configuration file

Fr my SR1. They sent me a link with several ones.

Please anybody can tell me which is the correct one to receive both
BAS and
HVS-1 Signals?
If you have two Ethernet leads to your SR1:
MC OFF, HVS-ENA

I don't recommend sending the data over the management port as it may
swap your LAN and possibly your Wi-Fi.

Ciao,
David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv



Re: Ciclone tropicale

Marco Martini
 

Thanks David for seeing this data I open another instance of metop menager but it gives me errors even though I have renamed exe

Il giorno mer 18 ago 2021 alle ore 12:50 David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺 via groups.io <david-taylor=blueyonder.co.uk@groups.io> ha scritto:
On 18/08/2021 11:19, Marco Martini wrote:
> Hi but Metop A data also arrives in hvs1 as well as noaa 20 how can I decode
> them? thank you

Marco,

For the full-world Metop-A coverage:
   https://www.satsignal.eu/software/metop_manager.htm

For the EARS local Metop-A data:
   https://www.satsignal.eu/software/AVHRRmanager.htm

Be aware that Metop-A data is finishing soon:
   https://www.eumetsat.int/plans-metop-end-life

Ciao,
David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@...
Twitter: @gm8arv







--
17° A.N.Carabinieri UMBRIA
Dir.Marco Martini
Tel.393/6939199


Re: Configuration File

David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺
 

On 18/08/2021 10:57, Vincenzo Mone wrote:
Hello to the list,
Thanks to David, I have sent an email to Eumetsat asking for the configuration file
Fr my SR1. They sent me a link with several ones.
Please anybody can tell me which is the correct one to receive both BAS and HVS-1 Signals?
If you have two Ethernet leads to your SR1:
MC OFF, HVS-ENA

I don't recommend sending the data over the management port as it may swap your LAN and possibly your Wi-Fi.

Ciao,
David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv


Re: Ciclone tropicale

David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺
 

On 18/08/2021 11:19, Marco Martini wrote:
Hi but Metop A data also arrives in hvs1 as well as noaa 20 how can I decode them? thank you
Marco,

For the full-world Metop-A coverage:
https://www.satsignal.eu/software/metop_manager.htm

For the EARS local Metop-A data:
https://www.satsignal.eu/software/AVHRRmanager.htm

Be aware that Metop-A data is finishing soon:
https://www.eumetsat.int/plans-metop-end-life

Ciao,
David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv


Re: Ciclone tropicale

Marco Martini
 

Hi but Metop A data also arrives in hvs1 as well as noaa 20 how can I decode them? thank you


Il giorno lun 16 ago 2021 alle ore 07:58 David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺 via groups.io <david-taylor=blueyonder.co.uk@groups.io> ha scritto:
On 15/08/2021 21:36, Marco Martini wrote:
> and i know but i don't know how to install it but with the taylor software it
> is not possible?

Marco,

You could use the HRPT Reader to process an image from the .hpt files saved by
the Metop Manager you have using the Metop-B instance.  See attached as an
example - you can play with the false-colours in the HRPT Reader, and use
Ground Map to alter projections.

The Pytroll/Satpy approach will work for MTG as well.

Ciao,
David
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@...
Twitter: @gm8arv







--
17° A.N.Carabinieri UMBRIA
Dir.Marco Martini
Tel.393/6939199


Configuration File

Vincenzo Mone
 

Hello to the list,

Thanks to David, I have sent an email to Eumetsat asking for the configuration file

Fr my SR1. They sent me a link with several ones.

Please anybody can tell me which is the correct one to receive both BAS and HVS-1 Signals?

 

 

Thanks

 

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520





      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 


Re: Still struggling for BAS & HVS-1

David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺
 

On 17/08/2021 18:28, Vincenzo Mone wrote:
David,
Thanks for Your Reply.
Unfortunately the link you gave me has dead link inside.
I mean if I click on the link you passed me:
https://www.eumetsat.int/media/45995
at the section 4.2 Automatic Configuration of SR1,
there is a link that to download the utility and the
configuration file to allow the SR1 to receive the
“EUMETCast Ku-Band DVB-S2” & “EUMETCast C-Band DVB-S” services .
The link is:
ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCast_Licence_cd/Windows/DVB _devices/SR1/SR1_Configuration_Files/
but clicking on it, it does not work.
I have stored in my backup Hard Disk, a folder called:
SR1CFG_DVBS2_ACTIVE_only-updates-DVBS2-radio-cfg_allversions
and in it there are 3 files:
README.txt
SR1CFG.cfg
SR1CFG.exe
They all have as date 2013 and do not know if they are still OK are they have been released new versions.
Finally you've suggested me to have a look at the EO portal to see if I am enable also for the HVS-1 reception.
I have been there and I clicked on EUMETCAST SATELLITE EUROPE - KU-BAND and got a very Long list
named SERVICE NAME and did not mentioned here to do not weigh down the mail.
I had a look in the list but cannot find anything that says about HVS-1.
Please can you tell me what should I have to look for to see if I can receive it?
Thanks in advance for your helps
73 de Enzo IK8OZV
Enzo,

If the link is bad, please report it to Ops. Ask for the updated config files too.

I cannot help further today. I suggest ensuring that the SR1 is up-to-date and then ask again.

73,
David GM8ARV
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv


Re: Still struggling for BAS & HVS-1

Vincenzo Mone
 

David,
Thanks for Your Reply.
Unfortunately the link you gave me has dead link inside.
I mean if I click on the link you passed me:

https://www.eumetsat.int/media/45995

at the section 4.2 Automatic Configuration of SR1,
there is a link that to download the utility and the
configuration file to allow the SR1 to receive the
“EUMETCast Ku-Band DVB-S2” & “EUMETCast C-Band DVB-S” services .
The link is:

ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCast_Licence_cd/Windows/DVB _devices/SR1/SR1_Configuration_Files/

but clicking on it, it does not work.
I have stored in my backup Hard Disk, a folder called:

SR1CFG_DVBS2_ACTIVE_only-updates-DVBS2-radio-cfg_allversions

and in it there are 3 files:

README.txt
SR1CFG.cfg
SR1CFG.exe

They all have as date 2013 and do not know if they are still OK are they have been released new versions.

Finally you've suggested me to have a look at the EO portal to see if I am enable also for the HVS-1 reception.
I have been there and I clicked on EUMETCAST SATELLITE EUROPE - KU-BAND and got a very Long list
named SERVICE NAME and did not mentioned here to do not weigh down the mail.
I had a look in the list but cannot find anything that says about HVS-1.
Please can you tell me what should I have to look for to see if I can receive it?
Thanks in advance for your helps


73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520




*********************************
****** GSM +39 328 7110193 ******
***** SMS +39 328 7110193 *****
*********************************

-----Messaggio originale-----
Da: MSG-1@groups.io <MSG-1@groups.io> Per conto di David J Taylor
GM8ARV ?????????????? ???? via groups.io
Inviato: martedì 17 agosto 2021 15:04
A: MSG-1@groups.io
Oggetto: Re: [MSG-1] Still struggling for BAS & HVS-1

On 17/08/2021 12:12, Vincenzo Mone wrote:
Hello All,

Apologise if I repeat a request that I posted time ago but still did no
resolved.

Please I would like to know if it is possible to receive both BAS and

HVS-1 at the same time using only one SR1, one Dish and 1 LNB with
multiple outputs.
[]
Any help will be really appreciated

Time ago David said to read the manual at:

ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCast
_Li
cence_cd/Windows/DVB_devices/Ayecka_SR1_DVB_Receiver_EUMETCast_
Setup_G
uide_v4A.pdf
<ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCas
t_L
icence_cd/Windows/DVB_devices/Ayecka_SR1_DVB_Receiver_EUMETCast
_Setup_
Guide_v4A.pdf>

Section: 4.5.2

But clicking on that side nothing happens. Nothing is loaded.

At this point I am in doubt that the HVS-1 should be requested to the
Eumetsat service.
[]
I am using:

PKIClient-x64-5.1-SP1.msi

eumetsat-setup-2.14.2_5

Are they correct or I need newer ones?> Are they correct or I need newer
ones?

If I need newer ones that could be the problem, where to get them as
it

Seems whichever link I click I get dead links.

Any help will be really appreciated.

I am also willing for a TeamViewer connection if someone want’s have a
try.

73 de Enzo IK8OZV
Enzo,

Yes an SR1 can receive both BAS and HVS-1 using a single cable from an LNB
connected to the receiver port you have selected as active.

The link is now: https://www.eumetsat.int/media/45995. It's best to set the
device parameters from the script provided by EUMETSAT, as detailed in
section 4.2.

You can log into the EO Portal to check whether you have any HVS-1 services
registered, but you should still connect to the Announcement Channel.

TelliCast 2.14.7 is the current version, but here:

https://www.eumetsat.int/reorganisation-eumetcast-satellite-data-flows

EUMETSAT say:

"Note: It is not mandatory to have Tellicast Client V2.14.4 to receive the
data, the required configuration changes work also with V2.12 or later. If you
have an older version, please contact our User Service Helpdesk."

I would advise against upgrading right away as the channels configuration file
differs.

The changes to the EUMETSAT Web site do seem to make it more difficult to
find what you want!

Good luck!

Ciao,
David GM8ARV
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv



Re: Still struggling for BAS & HVS-1

Vincenzo Mone
 

David,

thanks for your efforts but I the meantime you sent me this email,

I have still tried and now I issue also on BAS reception.

 

First I want to say that I am noticing strange behaviour when I go into the SR1 via Putty.

I mean I went into network with the menu 3 and got this:

 

 

I thought the problem was the Management IP Address as it is set all to 0,

so I thought I would set it up to 192.168.1.150 but when I enter the number 4

the page does not change I can se just flash like an update page but it does not let

me change it.

I had then the great idea to perform the initial setup of the Ayecka SR1 receiver but still get the issue.

Now I am stuck as I can't even receive anymore the BAS. I get the Yellow icon now on both BAS and HVS-1.

Please any help????

Thanks in advance

 

73 de Enzo IK8OZV

EasyLog 5 BetaTester

EasyLog PDA BetaTester

WinBollet BetaTester

D.C.I. CheckPoint Regione Campania

Skype: ik8ozv8520

 

 

 

 

      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 

> -----Messaggio originale-----

> Da: MSG-1@groups.io <MSG-1@groups.io> Per conto di David J Taylor

> GM8ARV ?????????????? ???? via groups.io

> Inviato: martedì 17 agosto 2021 15:04

> A: MSG-1@groups.io

> Oggetto: Re: [MSG-1] Still struggling for BAS & HVS-1

>

> On 17/08/2021 12:12, Vincenzo Mone wrote:

> > Hello All,

> >

> > Apologise if I repeat a request that I posted time ago but still did no

> resolved.

> >

> > Please I would like to know if it is possible to receive both BAS and

> >

> > HVS-1 at the same time using only one SR1, one Dish and 1 LNB with

> > multiple outputs.

> []

> > Any help will be really appreciated

> >

> > Time ago David said to read the manual at:

> >

> >

> ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCast

> _Li

> >

> cence_cd/Windows/DVB_devices/Ayecka_SR1_DVB_Receiver_EUMETCast_

> Setup_G

> > uide_v4A.pdf

> >

> <ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCas

> t_L

> >

> icence_cd/Windows/DVB_devices/Ayecka_SR1_DVB_Receiver_EUMETCast

> _Setup_

> > Guide_v4A.pdf>

> >

> > Section: 4.5.2

> >

> > But clicking on that side nothing happens. Nothing is loaded.

> >

> > At this point I am in doubt that the HVS-1 should be requested to the

> > Eumetsat service.

> []

> I am using:

>

> PKIClient-x64-5.1-SP1.msi

>

> eumetsat-setup-2.14.2_5

>

> Are they correct or I need newer ones?> Are they correct or I need newer

> ones?

> >

> > If I need newer ones that could be the problem, where to get them  as

> > it

> >

> > Seems whichever link I click I get dead links.

> >

> > Any help will be really appreciated.

> >

> > I am also willing for a TeamViewer connection if someone want’s have a

> try.

> >

> > 73 de Enzo IK8OZV

> >

>

> Enzo,

>

> Yes an SR1 can receive both BAS and HVS-1 using a single cable from an LNB

> connected to the receiver port you have selected as active.

>

> The link is now:  https://www.eumetsat.int/media/45995.  It's best to set the

> device parameters from the script provided by EUMETSAT, as detailed in

> section 4.2.

>

> You can log into the EO Portal to check whether you have any HVS-1 services

> registered, but you should still connect to the Announcement Channel.

>

> TelliCast 2.14.7 is the current version, but here:

>

>    https://www.eumetsat.int/reorganisation-eumetcast-satellite-data-flows

>

> EUMETSAT say:

>

>    "Note: It is not mandatory to have Tellicast Client V2.14.4 to receive the

> data, the required configuration changes work also with V2.12 or later. If you

> have an older version, please contact our User Service Helpdesk."

>

> I would advise against upgrading right away as the channels configuration file

> differs.

>

> The changes to the EUMETSAT Web site do seem to make it more difficult to

> find what you want!

>

> Good luck!

>

> Ciao,

> David GM8ARV

> --

> SatSignal Software - Quality software for you

> Web: https://www.satsignal.eu

> Email: david-taylor@...

> Twitter: @gm8arv

>

>

>

 


Re: Still struggling for BAS & HVS-1

David J Taylor GM8ARV 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🇪🇺
 

On 17/08/2021 12:12, Vincenzo Mone wrote:
Hello All,
Apologise if I repeat a request that I posted time ago but still did no resolved.
Please I would like to know if it is possible to receive both BAS and
HVS-1 at the same time using only one SR1, one Dish and 1 LNB with multiple outputs.
[]
Any help will be really appreciated
Time ago David said to read the manual at:
ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCast_Licence_cd/Windows/DVB_devices/Ayecka_SR1_DVB_Receiver_EUMETCast_Setup_Guide_v4A.pdf <ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCast_Licence_cd/Windows/DVB_devices/Ayecka_SR1_DVB_Receiver_EUMETCast_Setup_Guide_v4A.pdf>
Section: 4.5.2
But clicking on that side nothing happens. Nothing is loaded.
At this point I am in doubt that the HVS-1 should be requested to the Eumetsat service.
[]
I am using:

PKIClient-x64-5.1-SP1.msi

eumetsat-setup-2.14.2_5

Are they correct or I need newer ones?> Are they correct or I need newer ones?
If I need newer ones that could be the problem, where to get them  as it
Seems whichever link I click I get dead links.
Any help will be really appreciated.
I am also willing for a TeamViewer connection if someone want’s have a try.
73 de Enzo IK8OZV
Enzo,

Yes an SR1 can receive both BAS and HVS-1 using a single cable from an LNB connected to the receiver port you have selected as active.

The link is now: https://www.eumetsat.int/media/45995. It's best to set the device parameters from the script provided by EUMETSAT, as detailed in section 4.2.

You can log into the EO Portal to check whether you have any HVS-1 services registered, but you should still connect to the Announcement Channel.

TelliCast 2.14.7 is the current version, but here:

https://www.eumetsat.int/reorganisation-eumetcast-satellite-data-flows

EUMETSAT say:

"Note: It is not mandatory to have Tellicast Client V2.14.4 to receive the data, the required configuration changes work also with V2.12 or later. If you have an older version, please contact our User Service Helpdesk."

I would advise against upgrading right away as the channels configuration file differs.

The changes to the EUMETSAT Web site do seem to make it more difficult to find what you want!

Good luck!

Ciao,
David GM8ARV
--
SatSignal Software - Quality software for you
Web: https://www.satsignal.eu
Email: david-taylor@blueyonder.co.uk
Twitter: @gm8arv


Re: Still struggling for BAS & HVS-1

Philip Robinson
 

Enzo
I am running out of ideas how to help you may be someone with more experience can.
i can only repeat what i have said from the beginning.
I have a 1.2 metres satellite dish, from it there is just one cable. This is then split in to to cables in the house. One cable goes to the TBS6903 for which i receive HVS-2  and the other cable goes in to the SR1 box for which i receive BAS and HVS-1. this all works perfectly and i use some of Davids excellent software such as MSGDatatManager, Msg Animator, GoesABIManager, GEOSatSignal and EUMETcastview  for viewing and interpreting the downloaded data. I use windows 10 and two hard drives, the SSD has a large capacity (which is a must)
i have had occasional troubles in the past and have been helped really well on here and its usually some setting thats not correct.
I really have exhausted any idea what may be wrong.
I am sorry Enzo, i wish i could do more but i am not experienced enough, old enough but not experienced enough
I hope you get it fixed, i know how frustrating it is for you.
Good Luck..let me know when you sort it out. i would love to know the problem as well.
regards
Philip


------ Original Message ------
From: "Vincenzo Mone" <vimone@...>
To: "MSG-1 Mailing List" <MSG-1@groups.io>
Sent: 17/08/2021 12:12:34
Subject: [MSG-1] Still struggling for BAS & HVS-1

Hello All,

Apologise if I repeat a request that I posted time ago but still did no resolved.

Please I would like to know if it is possible to receive both BAS and

HVS-1 at the same time using only one SR1, one Dish and 1 LNB with multiple outputs.

I am currently only getting the BAS, while the HVS-1 icon remains yellow.

Please if it is possible what I need to receive also the HVS-1????

Any help will be really appreciated

 

Time ago David said to read the manual at:

 

 

ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCast_Licence_cd/Windows/DVB_devices/Ayecka_SR1_DVB_Receiver_EUMETCast_Setup_Guide_v4A.pdf

 

Section: 4.5.2

 

But clicking on that side nothing happens. Nothing is loaded.

At this point I am in doubt that the HVS-1 should be requested to the Eumetsat service.

Anybody can confirm????

I am using:

 

PKIClient-x64-5.1-SP1.msi

eumetsat-setup-2.14.2_5

 

 

Are they correct or I need newer ones?

If I need newer ones that could be the problem, where to get them  as it

Seems whichever link I click I get dead links.

Any help will be really appreciated.

I am also willing for a TeamViewer connection if someone want’s have a try.

 

 

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520





      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 


Virus-free. www.avg.com


Still struggling for BAS & HVS-1

Vincenzo Mone
 

Hello All,

Apologise if I repeat a request that I posted time ago but still did no resolved.

Please I would like to know if it is possible to receive both BAS and

HVS-1 at the same time using only one SR1, one Dish and 1 LNB with multiple outputs.

I am currently only getting the BAS, while the HVS-1 icon remains yellow.

Please if it is possible what I need to receive also the HVS-1????

Any help will be really appreciated

 

Time ago David said to read the manual at:

 

 

ftp://ftp.eumetsat.int/pub/OPS/out/user/EUMETCast_Support/EUMETCast_Licence_cd/Windows/DVB_devices/Ayecka_SR1_DVB_Receiver_EUMETCast_Setup_Guide_v4A.pdf

 

Section: 4.5.2

 

But clicking on that side nothing happens. Nothing is loaded.

At this point I am in doubt that the HVS-1 should be requested to the Eumetsat service.

Anybody can confirm????

I am using:

 

PKIClient-x64-5.1-SP1.msi

eumetsat-setup-2.14.2_5

 

 

Are they correct or I need newer ones?

If I need newer ones that could be the problem, where to get them  as it

Seems whichever link I click I get dead links.

Any help will be really appreciated.

I am also willing for a TeamViewer connection if someone want’s have a try.

 

 

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520





      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 


Re: OT for Philip Robinson

Philip Robinson
 

Enzo
The announcement channel address for HVS-1 is incorrect , it should be 224.223.222.223:4711
double check
Philip

------ Original Message ------
From: "Vincenzo Mone" <vimone@...>
Sent: 17/08/2021 10:41:49
Subject: Re: [MSG-1] OT for Philip Robinson

Hello Philip,

I have tried to change in the cast-client_hvs-1.ini file, the parameter from:

 

interface_address=0.0.0.0

 

to:

 

interface_address=192.168.10.150

 

Now running the HVS-1 .bat file in the log I get:

 

 

Any help please?

Thanks

 

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520





      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 

Da: MSG-1@groups.io <MSG-1@groups.io> Per conto di Philip Robinson
Inviato: lunedì 16 agosto 2021 21:25
A: MSG-1@groups.io
Oggetto: Re: [MSG-1] OT for Philip Robinson

 

Enzo 
That looks very similar to mine
except the interface address
I have attached my cast-client_hvs-1.ini
The interface address 0.0.0.0 is in my cast-client_bas.ini
May be your problem is there. I wonder if someone else can throw some light on this
Philip


Virus-free. www.avg.com


Re: OT for Philip Robinson

Vincenzo Mone
 

Hello Philip,

I have tried to change in the cast-client_hvs-1.ini file, the parameter from:

 

interface_address=0.0.0.0

 

to:

 

interface_address=192.168.10.150

 

Now running the HVS-1 .bat file in the log I get:

 

 

Any help please?

Thanks

 

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520





      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 

Da: MSG-1@groups.io <MSG-1@groups.io> Per conto di Philip Robinson
Inviato: lunedì 16 agosto 2021 21:25
A: MSG-1@groups.io
Oggetto: Re: [MSG-1] OT for Philip Robinson

 

Enzo 
That looks very similar to mine
except the interface address
I have attached my cast-client_hvs-1.ini
The interface address 0.0.0.0 is in my cast-client_bas.ini
May be your problem is there. I wonder if someone else can throw some light on this
Philip


Re: OT for Philip Robinson

Philip Robinson
 

Enzo 
That looks very similar to mine
except the interface address
I have attached my cast-client_hvs-1.ini
The interface address 0.0.0.0 is in my cast-client_bas.ini
May be your problem is there. I wonder if someone else can throw some light on this
Philip


Re: OT for Philip Robinson

Vincenzo Mone
 

Sorry Philip,

I posted the wrong file.

Here is the correct one:

 

 

Apologise

Thanks

 

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520





      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 

Da: MSG-1@groups.io <MSG-1@groups.io> Per conto di Philip Robinson
Inviato: lunedì 16 agosto 2021 19:49
A: MSG-1@groups.io
Oggetto: Re: [MSG-1] OT for Philip Robinson

 

Enzo,
I am not as clever as some of the helpful guys on here but i now wonder if you have the correct address for the announcement channel 224.223.222.223:4711. Have a look in the cast-client_hvs-1.ini  file for this.
It may be an idea to attach a screenshot of the cast-client_hvs-1.ini.
That may give us clues
Philip


Re: OT for Philip Robinson

Vincenzo Mone
 

Philip,

this is the screenshot of the cast-client_hvs-1.ini but I do not see in this file

the announcement channel 224.223.222.223:4711 how you said:

 

 

 

Thanks

 

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520





      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 

Da: MSG-1@groups.io <MSG-1@groups.io> Per conto di Philip Robinson
Inviato: lunedì 16 agosto 2021 19:49
A: MSG-1@groups.io
Oggetto: Re: [MSG-1] OT for Philip Robinson

 

Enzo,
I am not as clever as some of the helpful guys on here but i now wonder if you have the correct address for the announcement channel 224.223.222.223:4711

 

. Have a look in the cast-client_hvs-1.ini  file for this.
It may be an idea to attach a screenshot of the cast-client_hvs-1.ini.
That may give us clues
Philip


Re: OT for Philip Robinson

Philip Robinson
 

Enzo
I mean address 224.223.223.223:4711
Philip


Re: OT for Philip Robinson

Philip Robinson
 

Enzo,
I am not as clever as some of the helpful guys on here but i now wonder if you have the correct address for the announcement channel 224.223.222.223:4711. Have a look in the cast-client_hvs-1.ini  file for this.
It may be an idea to attach a screenshot of the cast-client_hvs-1.ini.
That may give us clues
Philip


Re: OT for Philip Robinson

Vincenzo Mone
 

Philip,

this is the final part.

Thanks

 

 

73 de Enzo IK8OZV
EasyLog 5 BetaTester
EasyLog PDA BetaTester
WinBollet BetaTester
D.C.I. CheckPoint Regione Campania
Skype: ik8ozv8520





      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 

Da: MSG-1@groups.io <MSG-1@groups.io> Per conto di Philip Robinson
Inviato: lunedì 16 agosto 2021 19:27
A: MSG-1@groups.io
Oggetto: Re: [MSG-1] OT for Philip Robinson

 

Enzo

Have you a screenshot of the log of the yellow icon Tellicast HVS-1. It may give an indication of what may be happening

Philip

 

------ Original Message ------

From: "Vincenzo Mone" <vimone@...>

Sent: 16/08/2021 18:07:24

Subject: Re: [MSG-1] OT for Philip Robinson

 

David & Phil,

Enzu



I have changed the MODCODS filter how suggested from Phil and from

the Link David passed me ( Thanks David ).

Here is the screenshot how it looks:

 

 

I hope it is correct but running both BAS-1 and HVS-1 I still see just one icon white

While the other one stays yellow:

 

 

Please have I missed something?

Thanks

 

73 de Enzo IK8OZV

EasyLog 5 BetaTester

EasyLog PDA BetaTester

WinBollet BetaTester

D.C.I. CheckPoint Regione Campania

Skype: ik8ozv8520

 

 

 

 

      *********************************

      ******   GSM  +39 328 7110193  ******

      *****     SMS  +39 328 7110193    *****

      *********************************

 

> -----Messaggio originale-----

> Da: MSG-1@groups.io <MSG-1@groups.io> Per conto di David J Taylor

> GM8ARV ?????????????? ???? via groups.io

> Inviato: lunedì 16 agosto 2021 16:46

> A: MSG-1@groups.io

> Oggetto: Re: [MSG-1] OT for Philip Robinson

>

> On 16/08/2021 15:33, Philip Robinson wrote:

> > Hi Vincenzo

> > I do not know whether your receiving my private email but any way.

> > If you want both BAS and HVS-1 received from the SR1, one idea might

> > be the configuration settings of the SR1.

> > Open telnet and go to the System (4)menu and check the MODCODS filter

> > carefully it has to be *0x00041000*.

> > regards

> > Philip

>

> Some help is here:

>    https://www.satsignal.eu/wxsat/Ayecka/Next-steps.html#modcod

>

> Cheers,

> David

> --

> SatSignal Software - Quality software for you

> Web: https://www.satsignal.eu

> Email: david-taylor@...

> Twitter: @gm8arv

>

>

>

 

 

Virus-free. www.avg.com

561 - 580 of 32268