Ernst, I can observe an increase in memory usage. Right now the service allocates 5.1GB of memory: root@openmediavault:~# service tellicast-client status|grep Memory: Memory: 5.1G the main

Markus, Here I have to change the driver stv090x.c in ./media as described. The point probably is that this only works if the the patched driver copy is newer than the replaced one. This is because

Ernst, total success. For unknown reasons, my CN dropped to 10,0 - 10,2 since about 4 UTC and I had the errors again. Compiled and copied your versions, rebooted, run setmc and everything is perfect

Markus, Let's take the shortcut. Here is the Igor M. Liplianin, CrazyCat enhanzed szap-s2 version you better use. All you have to do is add in channel.conf behind :hS1 more stuff: It should then

Hello, May I just add that I use Windows 10 home, 64bits. When trying to re-install the MSG D.M. I receive the message: error 126, WaveletDLL.dll. I must have lost this WaveletDLL somehow and I guess

Markus, I just tested with dvb-fe-tool that my version of szap-s2 correctly sets STREAM_ID = 1 ROLLOFF = 20 So this might be a last problem. I never understood, why EUMETSAT distributes an szap-s2

Markus, If you are in Germany even a C/N = 12dB should be possible with your 80cm dish. Here is my stv090x.c driver with 3 snipplets patched in for easy MODCOD setting. I tested it in many ways with

Hello, May I just add that I use Windows 10 home, 64bits. When trying to re-install the MSG D.M. I receive the message: error 126, WaveletDLL.dll. I must have lost this WaveletDLL somehow and I guess

Ernst you are my hero, like my physics teacher 40 years ago in my Gymnasium. I switched on Modcode All in BDADataEx and immediately the error rate went up and looked almost as bad as with the linux

Thank you for your kind prompt advise ! I do receive images from the Metop manager and Goes 16 ABI - still the Msg manager refuses to cooperate ! Perhaps David the creator of D.M. could more closely

---------------------------------------------------------------- Roland all is working fine with me, both Data Manager and the Tellicast client. As there has been no changes to either of these

Hallo, I run version 3.1.13.1309 with Multicast 2.1.4.2.5 client. Basic & HSV-1 come in but are not opened by the MSG D.M. Normal correct function until this morning, i.e. yesterday everything was

Markus, We get closer to the point: 1) SNR 9.6 dB is low even for an 80cm dish. I'am quite sure you can do better. 2) Link Margins (LM) are (3-4 dB is recommended!) BAS 8PSK 3/5 : LM = SNR

Ernst, I have seen a bit higher CN than 9.6 in the past (with my 80cm dish), maybe I need to recheck the pointing after "Sabine", but it is still good enough for Basic Service and that's all I want to

Markus, Could you also check that you load the right driver module. Maybe something went wrong when compiling and installing the TBS .../media/.. drivers? # modinfo stv090x shold show a first CrazyCat

Markus, Your low Signal, low C/N and bursts of coninuity errors all direct to your frontend. You should test the receiver with a *direct* connection to the antenna. Maybe szap-s2 or driver module

btw, this is the output of dvb-fe-tools --femon. I have not observed such unstable behaviour looking at the BDADataEx display. Lock (0x1f) Signal= -41,00dBm C/N= 9,70dB postBER= 0 Lock (0x1f)

Hi Ernst, Christian, had the chance late last evening to reboot and change the BIOS settings (disabled Intel Speedstep, disabled all C-States, btw. the NAS is a standard PC based on an ASROCK J4105

Markus, After disabling C-States in the BIOS completely (if possible) you have to know whether this is a driver or a TelliCast problem. You should have Manu Abrahams famous demodulator driver module

Markus, as Ernst wrote: did you look at the Bios and the C-States?! It's solves the problems here with my two 5925 USB devices under Linux. Regards, Christian Am 13.02.20 um 17:18 schrieb Markus