Date   

Re: Wye Turnout

cmdrwmriker
 

Hi Bob, I sent you a PM on this issue.
bill marshall

----- Original Message -----
From: Robert Herrick <rdherrick@...>
To: HOn3@groups.io
Sent: Sun, 08 Nov 2020 11:15:50 -0500 (EST)
Subject: [HOn3] Wye Turnout

I'm in need of one Wye turnout. I've used Fast Tracks jigs for years, but I have a hard time justifying investing in a jig for one turnout (but you do what you gotta do). Not interested in handlaying so my options appear to be BK or Railway Engineering. I have no experience with BK and my link to Railway Engineering no longer works. Need some advice.

Thanks!

Bob Herrick





Re: Wye Turnout

Wayne
 

Colorado Narrow Gauge has several code 55 and code 70 in stock now.  https://www.narrowgaugecolorado.com/?name=Catalog&mode=d&id=008

On Sun, Nov 8, 2020 at 9:48 AM Alan Kilby <alankilby@...> wrote:
The BK turnouts I got were on a skeleton loosely gauged that required spiking and gauging,they may have them gauged on ties.The quality of components were good but wait time excessive(3 months) and they were wrong turnouts when I got them first time.I would make sure to send description of what you want ,make sure they have order straight,talk to real live person if possible,I got 2 lefts instead of rights and they were code 83 not 70,get a time of when you will get turnout.When I talked with them on phone to tell them I got wrong order they were very accommodating and replaced them without question.This was 14 years ago so things have likely changed.
 Railway engineering website is currently down as he's building layout.
Alan

From: HOn3@groups.io <HOn3@groups.io> on behalf of Robert Herrick <rdherrick@...>
Sent: Sunday, November 8, 2020 8:15:50 AM
To: HOn3@groups.io <HOn3@groups.io>
Subject: [HOn3] Wye Turnout
 
I'm in need of one Wye turnout. I've used Fast Tracks jigs for years, but I have a hard time justifying investing in a jig for one turnout (but you do what you gotta do). Not interested in handlaying so my options appear to be BK or Railway Engineering. I have no experience with BK and my link to Railway Engineering no longer works. Need some advice.

Thanks!

Bob Herrick



--
Wayne Taylor


Re: Wye Turnout

Alan Kilby
 

The BK turnouts I got were on a skeleton loosely gauged that required spiking and gauging,they may have them gauged on ties.The quality of components were good but wait time excessive(3 months) and they were wrong turnouts when I got them first time.I would make sure to send description of what you want ,make sure they have order straight,talk to real live person if possible,I got 2 lefts instead of rights and they were code 83 not 70,get a time of when you will get turnout.When I talked with them on phone to tell them I got wrong order they were very accommodating and replaced them without question.This was 14 years ago so things have likely changed.
 Railway engineering website is currently down as he's building layout.
Alan


From: HOn3@groups.io <HOn3@groups.io> on behalf of Robert Herrick <rdherrick@...>
Sent: Sunday, November 8, 2020 8:15:50 AM
To: HOn3@groups.io <HOn3@groups.io>
Subject: [HOn3] Wye Turnout
 
I'm in need of one Wye turnout. I've used Fast Tracks jigs for years, but I have a hard time justifying investing in a jig for one turnout (but you do what you gotta do). Not interested in handlaying so my options appear to be BK or Railway Engineering. I have no experience with BK and my link to Railway Engineering no longer works. Need some advice.

Thanks!

Bob Herrick


Re: Wye Turnout

Wayne
 

You are looking for Shinohara 669-493 HOn3.  Harris Hobbies stocks them but are currently out.  They appear on eBay from time to time.  Jamestown Hobbies will make you one for about $35

On Sun, Nov 8, 2020 at 9:15 AM Robert Herrick <rdherrick@...> wrote:
I'm in need of one Wye turnout. I've used Fast Tracks jigs for years, but I have a hard time justifying investing in a jig for one turnout (but you do what you gotta do). Not interested in handlaying so my options appear to be BK or Railway Engineering. I have no experience with BK and my link to Railway Engineering no longer works. Need some advice.

Thanks!

Bob Herrick



--
Wayne Taylor


Re: Wye Turnout

lloyd lehrer
 

Bob, since you have the jig, just make half the right and half the left on the same ties and you will have a wye.

lloyd lehrer, (310)951-9097

On Sun, Nov 8, 2020, 8:15 AM Robert Herrick <rdherrick@...> wrote:
I'm in need of one Wye turnout. I've used Fast Tracks jigs for years, but I have a hard time justifying investing in a jig for one turnout (but you do what you gotta do). Not interested in handlaying so my options appear to be BK or Railway Engineering. I have no experience with BK and my link to Railway Engineering no longer works. Need some advice.

Thanks!

Bob Herrick


--
lloyd lehrer


Re: Wye Turnout

Mark Kasprowicz
 

I have the same problem with a crossing which I'll probably try making using one of their downloadable templates. I would have thought you could still use the Pointform and Stockaid should you try the same route. It's a real shame FastTracks don't hire their jigs out for people making one offs. 

Mark K
Oxon England,


Re: Conductive traces (was: Re: [HOn3] MDC Moose Jaws Loco)

Mark Kasprowicz
 

CircuitWriter pens used to be available in Radio Shack for either $9.99 or $12.99 and they do work very well. Easiest way of bonding them to wire is via a piece of PCB. Solder the wire to the PCB, glue the board in place then run the trace to wherever. One word of warning with this stuff, make sure the top is on firmly and even seal it with tape, because it dries very quickly.

The copper foil is paper based and great for wiring buildings etc but not for locomotives - it hasn't the strength and the movment of the wipers will cause it to fail. The Kapton based stuff does, it is strong enough to hold the wipers in place but will still flex to a certain degree plus the epoxy holds it firmly against the brass cover plate.

Mark K
Oxon England.


Wye Turnout

Robert Herrick
 

I'm in need of one Wye turnout. I've used Fast Tracks jigs for years, but I have a hard time justifying investing in a jig for one turnout (but you do what you gotta do). Not interested in handlaying so my options appear to be BK or Railway Engineering. I have no experience with BK and my link to Railway Engineering no longer works. Need some advice.

Thanks!

Bob Herrick


Conductive traces (was: Re: [HOn3] MDC Moose Jaws Loco)

Bill Lugg
 

Not directly applicable to the Moose Jaws topic, but possibly useful in general, here are a couple of links to materials that I've seen written about in the MR press recently:

https://www.amazon.com/CircuitWriter-Conductive-Ink-silver-based-4g/dp/B00B88B9KI/ref=sr_1_7?dchild=1&keywords=conductive+ink+pen&qid=1604849521&sr=8-7

This one was in an article in MRH I believe and was used to conduct power to lights in the shell of a diesel.  Unfortunately I don't remember how the wires were bonded to the trace now.

https://www.amazon.com/Zehhe-Copper-Foil-Double-Sided-Conductive/dp/B01MR5DSCM/ref=pd_bxgy_img_2/144-3426246-5575703?_encoding=UTF8&pd_rd_i=B01MR5DSCM&pd_rd_r=950798c1-d0db-4281-9bbb-d0a7a72f876d&pd_rd_w=LVqoV&pd_rd_wg=1ezQC&pf_rd_p=ce6c479b-ef53-49a6-845b-bbbf35c28dd3&pf_rd_r=3Y1XG0XNY30SRYGZFJPX&psc=1&refRID=3Y1XG0XNY30SRYGZFJPX

Here's the copper foil tape I think Dave is talking about below, 21.8 yards of the 1/4" wide material seems like it would last a long time for an HO model builder and the price seems pretty reasonable. I'm not sure it would solve Kevin's issue though.

HTH
Bill Lugg

On 11/8/20 8:23 AM, Climax@Mindspring.com wrote:
You can get that copper foil sticky tape at any outlet that deals with stained glass windows.  It can be gotten in most widths, a good variety to have on hand is recommended.   In addition to what has been talked about here, you can use it inside structures, stuck to walls or under "wall paper" or sandwiched between wood, or even painted, to run power around in structures.  To change directions one only has to fold the tape and never cut it.   I also use it for copper roofs on structures as well.  With the proper chemicals you can weather the "real copper" and make it various shades of green.
Dave

-----Original Message-----
From: Bruce
Sent: Nov 8, 2020 8:20 AM
To: HOn3@groups.io
Subject: Re: [HOn3] MDC Moose Jaws Loco

Not sure of availability in Europe but here in the U.S. Amazon has
it.  I bought a four roll pack (life time supply) for $12.  Search
"copper foil tape".

I used mine for a electric distribution bus inside my East Broad
Top roundhouse.

Never thought of it for on an engine or rolling stock. Thanks Mark!


Re: MDC Moose Jaws Loco

Climax@...
 

You can get that copper foil sticky tape at any outlet that deals with stained glass windows.  It can be gotten in most widths, a good variety to have on hand is recommended.   In addition to what has been talked about here, you can use it inside structures, stuck to walls or under "wall paper" or sandwiched between wood, or even painted, to run power around in structures.  To change directions one only has to fold the tape and never cut it.   I also use it for copper roofs on structures as well.  With the proper chemicals you can weather the "real copper" and make it various shades of green.
Dave

-----Original Message-----
From: Bruce
Sent: Nov 8, 2020 8:20 AM
To: HOn3@groups.io
Subject: Re: [HOn3] MDC Moose Jaws Loco

Not sure of availability in Europe but here in the U.S. Amazon has it.  I bought a four roll pack (life time supply) for $12.  Search "copper foil tape".

I used mine for a electric distribution bus inside my East Broad Top roundhouse.

Never thought of it for on an engine or rolling stock.  Thanks Mark!


Re: MDC Moose Jaws Loco

kevin b
 

Couldn't you pick up off the insulated side of the drivers with some 
carefully placed wipers?
Just a thought...
Bill Lugg

actually, that was my first plan for picking up current. i may still yet do that, depends on how well things work.
thanks for the input.
Kevin.


Re: MDC Moose Jaws Loco

Bruce
 

Not sure of availability in Europe but here in the U.S. Amazon has it.  I bought a four roll pack (life time supply) for $12.  Search "copper foil tape".

I used mine for a electric distribution bus inside my East Broad Top roundhouse.

Never thought of it for on an engine or rolling stock.  Thanks Mark!


Re: HOn3 standards gauge

Bruce
 

I model the East Broad Top.  They mounted standard gauge cars on narrow gauge trucks and ran them across much of the railroad.  I use a NMRA HO gauge to ensure clearances on my layout.


Re: HOn3 standards gauge

Mark Kasprowicz
 
Edited

Perhaps the NMRA is going to correct the HOn3 gauge. The overall clearance on the metal version does not allow for the largest HOn3 locomotives such as D&RGW K37's which were coverted from standard gauge locos. It was fine for Baldwin C-class, but too small for some of the K's (not sure exactly where the dividing line is). I was told to use standard HO clearances for this dimension.
That said the metal version still available from the NMRA

https://www.nmra.org/store/products/hon3-standards-gauge

Mark K
Oxon England,.


Re: MDC Moose Jaws Loco

Mark Kasprowicz
 

I just looked, and on Ebay UK it's here.

https://www.ebay.co.uk/itm/FLEXIBLE-POLYIMIDE-PCB-MATERIAL-KAPTON-DUPONT-AP-GTS-FLEXIBLE-KREMPEL/283961471252?hash=item421d6c3114:g:QoEAAOSwMVdYG2aQ

It is available in the US but I only found it in rolls large enough to last many lifetimes costing $$$$$'s.

Mark K
Oxon England.


Re: MDC Moose Jaws Loco

Robert Bell
 

The other option is to just make a new cover plate from PC board material.  Add phosphor-bronze wipers, and wire it up.  See attache'd pict.

Rob Bell





Re: MDC Moose Jaws Loco

Mark Kasprowicz
 

It's fairly standard to glue a narrow piece of PCB board on the insulated side of a loco and solder phosphor bronze wire onto it as wipers.
Using a trailing truck even a four wheel one gives just two wheel pickup on a narrow wheelbase - that's going to result in the supply having continuity issues, especially on turnouts.
There is an alternative to PCB ties and that is copper coated Kapton sheet. It's not easy to find (I got mine from the Czech Republic!) but its much tinner than ties, can mould to a shape and can be cut with scissors or a craft knife. The only thing to watch out for it making sure that the edges are insulated from the frame and I do that by letting the epoxy flow out from the sides slightly and check for insulation with a multimeter before the glue sets.

Mark K
Oxon England


Re: MDC Moose Jaws Loco

Mike Conder
 

Yes, that works and is better than relying on tender or pilot trucks.  

IIRC best way was something about epoxying a PC tie to the gear cover plate, with phosphor bronze wire solder to it so it can rub on the back tread of the insulated driver.  May be thinking of another loco though ... been a while since I looked into it. 

Mike Conder

On Sat, Nov 7, 2020 at 10:41 PM Bill Lugg <luggw1@...> wrote:
Couldn't you pick up off the insulated side of the drivers with some
carefully placed wipers?

Just a thought...
Bill Lugg


On 11/7/20 7:25 PM, kevin b via groups.io wrote:
> I'm VERY interested!
> Mike Conder
>
> Hello All.
>
> caught a break today, actually had some time to tinker at the train bench:
>
> made a little progress even.
>
> one thing (trailing truck)  is now decided. it will be a ?-8-4t.
>
> as this is a saddle tanker, i will have to pick up one leg of current
> from somewhere, so, it will have to come from the trailing truck, and
> possibly the lead truck.
> the drivers will supply the other leg.
>
> thanks.
> Kevin.
>






Re: MDC Moose Jaws Loco

Bill Lugg
 

Couldn't you pick up off the insulated side of the drivers with some carefully placed wipers?

Just a thought...
Bill Lugg

On 11/7/20 7:25 PM, kevin b via groups.io wrote:
I'm VERY interested!
Mike Conder

Hello All.

caught a break today, actually had some time to tinker at the train bench:

made a little progress even.

one thing (trailing truck)  is now decided. it will be a ?-8-4t.

as this is a saddle tanker, i will have to pick up one leg of current from somewhere, so, it will have to come from the trailing truck, and possibly the lead truck.
the drivers will supply the other leg.

thanks.
Kevin.


Re: HOn3 standards gauge

Mike Mackey
 

Have you read the correspondence from the organization regarding rolling out a new store? I just went to the site and found On3, Sn3, HOn3 and standard gauges. It’s there guys. Are you logged in as members?

Mike

On Nov 7, 2020, at 8:16 PM, Dale Buxton <dbtuathaddana@...> wrote:


I looked on the NMRA store page on the web and could not find them in HOn3. I wonder what is going on?

Dale Buxton 

On Sat, Nov 7, 2020 at 4:02 PM duncan <train3guy@...> wrote:

Eric,

    Is your question related to the fact the NMRA has just released plastic clearance gauges for most of the various scales and gauges, including ones for On3 and On30, but nothing for HOn3, which I believe is a larger market that the other two combined?  This would not be the first time the NMRA has done some pretty squirelly (sp?) things.

                                                                                                                                                                                                                                                                Duncan Harvey

On 11/7/2020 10:26 AM, Eric Schrowang wrote:
Does the NMRA no longer make the HOn3 standards gauge? What are others using in place of it?

Thank You
Eric


--
Mike “Rustler” Mackey

1781 - 1800 of 8625