I gave the pot a workout, with 100 passes from min to max. This seems to have corrected the issue. 73 - Dave N3RD

The subject controller is RT-21 v4, S/N 04841. The controller responds properly in MAN mode to CCW and CW commands from the front panel buttons. However, after a short time (a second to a few seconds)

Jeff, I replaced my G-1000 with a 2800 and downloaded the most current configuration software from your site. I did a cal but I no longer go in OT. I’m sure I’ve missed a step or two. It is south faci

Hi All, If this question is not acceptable to the purpose of this group, please flag and I will delete. I picked up a Green Heron RT21 last year. Its currently controlling a old CDE Ham M rotor. While

More – The SPIDS use 4 wires control cable, and they have no limit switches (which the RT-21 handles well). This means you don’t care about antenna alignment when you install as you can adjust everyth

Purchased new RT-21 configured for CDE rotator. Did a factory reset and reconfigured all the jumpers as well as selected, changed and saved the Yaesu rotator. Checked and double checked. Wired up the

We have released version 2.7.7 two requested new features after the recent 2.7.5 and 2.7.6 versions. 1. Better Rotor Preset windows for visibility and touchscreen use. 2. Automatic installation for mu

Setting up SatPC32 to directly control the RT-21. I could not find the RT-21 listed in the Rotor Interface pull down menu. The RT-21 server was found in the RT-21 folder but the program did not see it

Jeff, The program GH Tracker, it talks to the RT-21 and shows the current position, but I can't get it to see the DDE data from my tracking programs. SatPC32 is set for DDE and I can track it if I use

Hello everyone, I need your help. I just installed the LAN cable from the RT-21 to the router, I went to my router's firewall (Iqrouter) and there to Port Forward. I attach an image of how I configure

Jeff, I'm using the Green Heron remote switch. I have the switch selector screen parked at the lower right corner of the second monitor. When I launch the controller it puts the switch selector in the

We have an RT-21 AzEl that was shipped in early 2019…our project got delayed due to the drama. So it was unused in the box. On boot up, both parts show FW 1.04. The label on the bottom has a serial nu

Every installation of GHE Client that I have made seems to have problems with hot keys. I just completed bringing up a completely new Windows 10 Pro computer with a fresh install of 2.7.7. I completel

Hi Jeff and the group, I have the RT-21 Deluxe and the Yaesu G-1000 setup on my bench using a temporary cable to make the connection between the rotor and the RT-21. When I first turned everything on

Having got the elevation working, on connecting the azimuth Motor and indicator, I noticed that the LED on the sub lunar PCB board was no longer Green, and any indication I had showing that the elevat

A qustion for Jeff Will the PST program need to reflect the different pulse count or are relying on The RT-21 to just take in the bearing information and translate to popsition. On the Spid you had to

I am attemting to wire up a new Sub Lunar AZ EL rotator. Both motors have the same wiring and are coloured on the Motor feed as Red Black and Grey, which I take is Red +, Black -, grey R. The colour o

At our station, the GHE Server computer, Base and Remotes are over 100' from the operating position. We are using 10 WIO Profiles on 6 Remotes to control our (relatively complex) transmit antenna sele

As recommended by Jeff, we will be using the "pop up" rotor preset display that appears when you tap the name of the rotor in the tray, and disappears after tapping on a direction. Since the preset di

Experimenting with how the rotator displays work under N1MM software band control. There are three relevant displays: Tray Map Presets Tray and Map displays follow the N1MM UDP on port 12062 on the NU