On my FTDX101D, I can use the screen and "REC/PLAY" menu to succesfully record voice messages. I have BK-IN on and am in USB mode. Playing back the message keys the radio and plays back the message ov

Hi, * For contests and crowded CW band conditions has anyone found the need for the 300hz roofing filter? How much time did it add to your order for the vendor to send the radio back to Yaesu to insta

Hi all, I am in the race for an Acom A1200S amplifier and I wonder how should I be able to connect the CAT cable to the amp, so that frequencies are automatically set when a band change is initiated o

Goodnight all, I notice several "clicks" or fairly loud snaps coming from the station when it heats up... - that's not coming from the fan --- Do you have this phenomenon.. it looks like something exp

I'm having an interesting time understanding the ALC meter function. I'm helping a friend setup his new FTdx101. I was listening to his SSB signal on 40. I sounding like his audio was weak. I told him

My Answers: 1) 300Hx roofing filter.... I find the filter of modest importance. Not sure If I would get it again. Just me. 2) I do not know about the DVI port issue, I use Ham Radio Deluxe (HRD) which

Just a few weeks ago I purchased a brand new, fully loaded Yaesu FTDX101MP. I have been following various folks advice of how best to set-up the AMC Level, MIC Gain and Processor Level. What works bes

It's been some time since yaesu released an update .... MAYBE during Dayton Hamvention??? Hummmmm?!?! Scott W2ntv

Hello, I'd like to use my new WinKeyer USB with my FTDX101D. I use the N3FJP program and have configured it to talk to the WinKeyer on port 9. From N3FJP's CW setup screen, I can test the WinKeyer and

I have a new FTdx101MP arriving next week with the full TX enabled. Can anyone tell me if this would enable the ability to TX in the new 40MHz band? This is a new band here in Ireland, so it would be

Currently on my FTDX101D I have the Yaesu M-1 microphone. I just purchased a Mercury IIIS amplifier. For the amp to transmit it needs the PPT signal from the back of the radio. Is there a way to turn

*AUDIO + ALC to ZERO + POWER OUTPUT WRONG* Strange: with a friend's FTDX101MP, if I put a single AUDIO TONE in TX to check and set the usual AUDIO-DIGITAL transmissions such as FT8 SSTV AFSK ... for e

Hello, It appears that the factory set minimum power on this transceiver is 5 watts. Is it possible, via any hardware setting or with any control software to CHANGE the minimum to say, 2 or 3 watts? T

Powered on my 101D this morning and get the message "Insert Firmware SD Card" and "Touch the screen to continue" I can't power OFF using the On/OFF switch. I have previously updated to the latest the

Too much gear. FTDX101D serial 1K300274 purchased Oct 15, 2021. I placed it on the desk, it plays perfectly, no scratches, no nothing. Great rig. Includes matching hand mike, power cord, USB cable, an

Hello OM's and YL's, I wanted to ask if there is also a possibility to remote control the 101D or 101MP with an Android or IOS App or is there only the SCU Lan 10 for Windowds. FlexRadio has an app fo

I finally shipped my 101MP to Yaesu on May 9th to have the "HiSWR" fault repaired. It was received at the factory on the 17th. I understand from Tim Factor that the facility was shut down for 1 week b

Why can't I tune my FTdx101MP on 70 MHZ using the tune button? -- 73 Jan PA4JJ ______________________________________________________ My dxspider clusters running 24/7 on a raspberry pi 2 pa4jj-2 teln

Can the front panel mic and USB audio input be used at same time? I need to use computer audio and mic audio when in SSB mode

I have searched the manual but could not answer this Question. Is there a menu setting to pick which port to use or are they both "live"? Phil W8UV