Hi all, Just to share a short video showing the FTDx-101D running both receiver at same time, one horizontal dipole and second vertical dipole. YouTube stereo audio keeps main receiver on the left cha

Anyone also have or had the FTDX5000 and now have the 101D/MP? On the 5K in CW mode I can use the tuning indicator to perfectly zero in on a station. Is there a way to do this with the 101? Also, the

Have setup DiGi mode here using the data port on the back of the radio and use USB mode (this to be able to use the extra RX bandwidth). The phenomenon: When I select both receivers to be displayed om

I’m close to getting Fldigi working with my new FTdx101D. I can decode RTTY. But I can’t transmit characters. If I click T/R, the rig goes to transmit and I get a steady carrier. Typing results in the

I'm a new user and I know this topic has probably been beaten to death. I've owned lots of rigs and never had so much trouble getting HRD-DM780 & WSJT-X to talk with one another. Yes I've read the tut

N1MM worked fine in arrl dx contest . updated n1mm software this morning. tried to set up for russian dx but no communication to ftdx com ports in device manager seem to be ok. winkeyer works but no i

I have assigned RF Power to the CS button on the 101d. I always thought it odd that if you push the CS button nothing would happen, you would have to rotate the outer knob to make it display the power

Nothing earth shattering. There's a new PDF manual that corrects page # references, corrects the contest keyer serial number range from 999 to 9999, and on page 93 changes AM to DATA on REAR SELECT de

Hello So… from the touch screen, the AGC can be set to various settings, Slow, Med, fast and Auto. can these settings be adjusted within the menu section? and if so, where? the manual mentions this, b

Just got a 101D today. Installed the drivers in the usual manner with no problem. Went to connect to some of my favorite software and nothing. I've tried HRD, DXLab Suite, and ACLog and nothing will c

I had the following email from Yaesu about compatible wireless mice:- FTDX-101D/MP COMPATIBLE WIRELESS MOUSE/KEYBOARD ISSUE Will the radio support Bluetooth Mouse/USB? ANSWER The FTDX101D will support

WSJT through the USB connection is working fine, but I have to set the PC (Win 7) to Playback 6, Record 5 is there a setting on the 101 that would allow me to increase the PC volume while reducing the

Just got WSJT-X working. Should I see only a little ALC or max ALC (up to the blue line)? And, what do you folks use to sync your clock with Windows 10? I tried time.window.com but I’m still off a bit

This worked to sync my clock on Windows 10: Open and administrator command prompt (right click start) net start w32time w32tm /resync Time.is then reported the time was exact. Carl Yaffey K8NU 614 268

I know this has been done to death, but power out on SSB. On every other rig I've had if you whistle it up the PO meter shows 100w. On the 101 the maximum i can show is 50 to 60w. I know its not a pea

Can anyone tell me what settings are needed for both fldigi and the 101. It RX OK and the PC is putting out audio on TX,but it is not switching the TX on. Im thinking of putting Signalink back on, no

FYI, There is a recent thread on the Elecraft K4 reflector critiquing the FTDX101. It started as post to take the place of critiquing the K4 since nobody had yet gotten K4. Some posters are regulars h

I've just got the 101d this morning and I'm in the process of setting it up. Its all working except WSJT. The RX is fine, but I can't get it to TX. Any help with settings would be much appreciated. Th

For some reason, my PC stopped talking to the 101MP, yet device manager showed the Yaesu com ports there. So, I deleted the 2 Yaesu COM PORTS in the device manager. Then I reloaded the Yaesu COM PORT

For some reason, I can not get the VOX to work. Ive used it before but discovered in the ARRL SSB contest that it no longer works. Other than the VOX gain, VOX Delay and Anti VOX, is there another set