I had the ERR 12V message come up yesterday and between the internet and the manual I was able to, I thought, get the situation resolved by resetting the circuit breaker on the back of the radio. I ha

Just curious... Are there any K3 and/or P3 firmware updates in the pipeline? Either bug fix or feature update? TIA... 73 Ken S. N4OI

My K3S hand mic isn’t working. Any suggestions where to start looking for the problem? Thanks. Craig

As I prepare for the arrival of my K4D, I wish to send my K3s and P3 onto a new home. I am the original owner of the K3s (SN:11276) it was factory assembled and has: - Auto tuner - 100watt amp - 2.8kH

Last fall one of our K3 radios stopped putting put any power during the last few hours of the CQ WW CW contest. For many reasons I am finally getting back to looking at this failed radio. I swapped in

K3s - Never outside - non smoker - like new. Fully equipped. Including P3 Panadapter - TX Monitor. All details supplied upon request. $3,200.00 US VA2AGW

I have an Elecraft K3S-F purchased at Dayton in 2018. It includes: 100 W upgrade factory installed (KPA3A-F) ATU for K3S factory installed ((KAT3A-F) K3 TCXO 1 ppm factory installed (KTCXO3-F) 2.8 fil

All, Ever since I upgraded the KIO3A board in my K3 s/n 261 to a KIO3B board, I get an intermittent "Illegal Opcode" error, followed by a reboot, on my P3 s/n 688. Both devices are running the latest

I've noticed huge noise on the display when tuning around with the K3 on 6. Not quite as bad on 10. Any cures for this? Thanks Ron N4XD Sent using Zoho Mail

In search of an SP-3 Speaker. Anyone have one they care to get rid of? 73, -- Lee Young, K5LY FOC #2062, CW Ops #1124, FISTS #15371, SKCC #7448 CW Forever!

It appears that the RemoteRig website and DNS Server is offline. No further info is available. I discovered that you can use a personal DNS Server e.g. no-ip for the RRC-1258 / K3 combos. Dan K4FN

Good morning all, On the off chance, does anyone in the UK (or Europe) have a spare KPA3 gold pin repair kit? I can order one direct but the $40 kit costs $80 to ship. Waters & Stanton / Navada don't

Elecraft K3-0 Remote head and manual Remoterig RRC-1258 MKII (2 pcs.) All cables and PS for 1258 (2) User Manual for RRC-1258 MKII $675.00 ins. and delivered Cont. US Pictures on request 73 Thaire W2A

DOH! I checked the key out cable from the 890 with an ohmmeter and sure enough it was almost a short. So I didn't have to hunt long to find the problem - there was a tip-ring-sleeve plug from the 890

Solved! ( https://groups.io/g/Elecraft-K3/message/39064 ) ----------------------------- It's the time for weird things happening. My iPhone 13 played dead today (that's another story) and now my KPA15

First licensed at 14, I'll be 80 in a few months. After my wife's passing, I've lost interest in several things, ham radio being one. I have a K-Line, but it has been turned on less than 10 hours in t

Hello all My K3 was constructed by me in September 2010 and has been used on a number of DXpeditions. However a few years ago it developed an audio fault - no loudspeaker output but OK on headphones.

Hello! I have a KRX3 sub receiver I'm going to install into my K3. I have all the instructions, etc. but wondered if anyone on here had some advice on what to look out for, or do's and don'ts? Also an

Hello, Does anyone know if the cable which carries data from the Panadaptor Power Sensor, to the W2 Wattmeter, can be replaced with a standard CAT 5 Ethernet cable? -- 73, and thanks, Dave (NK7Z) http

Current setup. K3 with P3 early serial. Back to factory for complete update. Gold Pins etc. Today K3 shut down. Found blown 15 amp fuse in ground side of power supply cable Power supply is MFJ 4035MW.