I just was given a HP 24ea monitor which has 2 internal (2W) speakers. I'd like to use these for my K3 external speakers. Beside setting SPKRS config to 2, are there any issues using this kind of spea

Today I encountered the ERR12V Message and the smell was not fine. I was running about 90 W in Vara into my well macthes Yagi Antenna. What I have found was that the Connectors going into the 20A Fuse

For some reason, all of a sudden my K3 won’t connect to my logging program. Yesterday it showed where the B vfo was but not the A. Then today it doesn’t show either. I’ve not made any changes to anyth

This is SERIOUSLLY off topic (like many posts here)….but….I have two big boxes of cards from an estate sitting here looking for homes. 1950s-present day. Any takers? Hamgallery will take very old ones

Which brings up a more serious question ... What to do with a beloved ham's logbooks and QSL collection when handed over by a family who doesn't want them (of when there is no family), is a trivial qu

Good day, all! For sale, my factory built K3 #7551 with KPA3 100w, KAT3 antenna tuner, KBPF3 for SWL, KSYN3A 2nd generation synthesizer, USB port, internal sound-card, KXV3 I/O board, P3 Pan-adapter w

Hi everyone... I have a K3 - ten-watt version... Super light.. nothing else in there but the 2.7k and 600hz filters... I was thinking about putting it out on qrz or qth, then was going to ask on this

I have a new Windows 10 computer and the computer is not finding the Com Ports for my KAT and KPA 500. They are showing as FT232R USB UART'S . And showing as Failures? Where can I find the correct dri

Moderates, please delete if this subject is not allowed. I am wanting to use a Beverage RX Antenna with a K2-10. I need to use an external TR switch to handle switching between the 2 antennas. I am no

I sent my K3 in for repair mid December and was told I was #3 in the que. I haven't heard when I might get my K3 back and am wondering if others have had this long a delay? I think Elecraft support do

On Fri, Feb 3, 2023 at 05:54 PM, Ray Maxfield wrote: I think your Asking too much of the radio ! You need one of the Field Day Filters that came around a few years ago…… There are several approaches t

New K3 owner question: The BAND up/down control on the K3 is documented as a way to navigate through the ham bands, but what it actually does is navigate to whatever the last frequency you were at whi

When installing non-INRAD filters (the ones with discrete crystals on a PCB), there is an Elecraft sticker on the filter module with the bandwith and the frequency offset (handwritten) one has to prog

Hello! I have a KRX3 sub receiver I'm going to install into my K3. I have all the instructions, etc. but wondered if anyone on here had some advice on what to look out for, or do's and don'ts? Also an

I have a friend that has a K3 serial number 68XX, He is having problems with loss of signal on all bands, strangely signals show up on the P3. I think it may be pin connection problems. Nonetheless he

Looking for suggestions. My K# works well in cw and ssb but though it previouly operated without problems in TX Data when using WSJT at present it only presents a single tone and no power output. The

Has anyone put an KSYN3 back into an upgraded K3 (with KSYN3A)? I'll explain, I have an older K3, serial # around 3000 that I upgraded with a new KSYN3A board and 6m preamp board a few years ago... I

My Cady K3S manual seems to say that for diversity reception, I must connect my second (receiving) antenna to the Aux RF BNC, and then set the sub receiver to Aux. Is that correct? I would like to be

Early K3S, with a KPA3 (100W PA from an older K3) and KAT3 (antenna tuner, also from the old K3). After a few compatibility issues in moving the older option boards over to the new K3S platform, there

My Auto Tuner does not want to accept any more Tuner config’s on 80 meters. I tried to go to Config: KATE3 to Clear it, but it did not Work. Ray WA6VAB K3…… tnx