In addition to the KPA500 & KAT500 Utilities, are there any remote programs that can control the amp and tuner remotely either through the USB port or an Internet connection? Thanks, Irwin KD3TB

I do not know if I have an encoder problem. When I tune my K3 rapidly with the main knob, the frequency display seems to jump around. However, when I tune slowly, or when I use the RIT knob for fast t

Hi A friend of mine has a K3S he`s 90 years old and does not do the internet so I have been tasked with helping him find a solution. I have tried to get support from Elecraft and their just not intere

I have a K3s that I use with an Arduino to allow me to run remotely using RemoteHams.com. The Arduino pulls the Pin 8 of the 15 pin connector. There is also a timeout timer so that if case I loose com

Hi, I bought my K3 used about 10 years ago and I can't remember what options are installed in the radio. Is there any software that provides an inventory of what is installed? 73 Randy, K7AGE

Howdy, If anyone out there is kitting out your K3 and are looking to sell the USB audio upgrade components, I am in the market for one. I know this is a slim chance, but since Elecraft is no longer se

I have a problem with sending FT8, using my K3/KAT500/KAP500. The set up receives and decode properly. Keying the K3. But no RF out. I have the filters wide open. The micro Keyer II and WSJT-X are set

K3/100F K3 100W Transceiver - Factory Assembled S/N 1707 KAT3-F K3 ATU - Factory Assembled KFL3A-400 K3 400 Hz, 8 Pole Filter KFL3A-2.8K K3 2.8 kHz, 8 Pole Filter KUSB Universal Serial Bus Adapter KSY

Wondering whether anyone else had experienced a 3.3 to 3.5mm adapter breaking apart IN the paddle Jackson a K3? The tip and ring portion of the adapter are now stuck inside the paddle jack on th at ra

Quick update on my broken plug problem. The suggestion to use a tap to remove the broken plug tip helped a little. It removed the plug ring and ring insulator, however, the tip of the plug is still tr

The Elecraft 75 Meter net is moving to 3.835 at 01:00 UTC tonightdue to busy frequencies Paul KB9AVO

Due to people wishing to sit next to us and throw carriers ... I am moving us a small distance away... AND there is the chance someone will be there ... 75m is funny that way Please take note of 3.825

I downloaded the KX3 utility into my laptop this morning. It's a WIN 10 system. I also have the KXUSB cable that came with the KX3 when i bought it 2 years ago. After downloading the utility program i

This an old microphone but it was causing me issues. The mic element was wired so that it was always connected. That allowed shack noises to trip the Tx on in the VOX position. i rewired the mic eleme

I’m contemplating a http://www.q5signal.com/ 144MHz transverter to use with my K3S. Does anyone have experience with these devices? I’m thinking of buying the 75W version. Some questions, if you can a

Just developed an issue this past weekend during the CW contest. I now get an ERR KP1 message on 20-10 meters. I bought the K-Pod less than 2 months ago, and this is the first I've noticed this issue.

Purchased a used K3 (excellent condition), studied the "Owner's Manual" (Revision D10), installed "K3 Utilities" and updated the firrmware to 05.67 (the latest). Bellow the Temperatur vs. Time I logge

Many apologies for the missing Net Control. about 15 mins before it was to start, I kicked 80 meter on and had a mindblowing SWR.. went out and had a branch come down on it. I tried to make the 40 wor

It seems like several months ago Elecraft sent a note about some add-ons that were no longer available, including the 2 meter transverter. I am at the point whre I would really like to add 2 m to my K

I want to ask if the tech support contact form on the Elecraft site does work. I tried to order the "Rubber Switch Array", part # E100200 to solve my problems with intermittent action of the front pan