Dear friends, I sent the pre-order proposal for the K3 kits for K3S, but so far I have not received any response from Elecraft. Does anyone have any news. Thank you and 73, de PY3IOD - Antonio

Can someone please measure the conversion gain (in dB) of an Elecraft K3 from ANT to IF OUT (with 50 Ohm load on the IF OUT port) on any or preferably all HAM bands? I can also do with data measured w

Sale of this item is currently pending, awaiting funds. 73 Jim K8JK

- Elecraft P3 TXMon Adapter UNUSED! Brand New Unused Elecraft TXMon adapter for Elecraft P3. Previous owner never had the opportunity to install in their P3. Sealed module, and hardware bag, complete

I have a remote tuner so I hold the "tune" button to send a low power carrier for the tuner to operate. The tune power is set by the config parameter TUN PWR. This works great for every band but 30 m,

I'm putting my K3 (Serial# 6384) up for sale. Do not reply to the list, I will only reply to direct emails if you convince me you are serious and then we set up time to talk on the phone (any cc'd rep

Hello, During the RTTY contest last weekend we noticed a problem that our transmitted text was abrupted. A lot of times our call was transmitted as PI4C or PI4CO instead of PI4COM. We used the latest

Good day, one and all. I finally got my K3 working with WSJT-X/RumLogNG running on my macOS box and connected via the microKeyer II sound card to the K3’s line-in/out connectors. It took some struggli

Hello All, I am refering to the K3 Schematics at https://ftp.elecraft.com/K3/Manuals%20Downloads/K3_Schematics_Jun_2010.pdf. On page 35 (K3: AF Filter) the two inputs to the filters are TP1/AFIN1 and

https://elecraft.com/pages/shipping-box-sets-item-return-for-servicing Here's a link to the order page, for different boxes.

They sell the shipping boxes Chuck Jack Hawley KE9UW Sent from my iPhone, cjack

In response to Quin and Jim's suggestion, I have just cleaned the paddle contacts. No joy, unfortunately. Still no dahs. Has anyone else had the problem and traced it down to an internal problem? 73 -

My K3S s/n 11064 has a new problem, which first occurred on Sunday October 4, 2020. My primary mode is CW, and since the radio arrived in December 2016, I have been relying primarily on the internal k

Has anyone had mis triggering? Often used buttons trigger the wrong macro sometimes. This is my third one. They last about 6 months and then mis trigger. I moved the macros on the offending buttons to

One of the challenges I’ve had with operating remote was leaving the K3 on when departing this could be for the office, To visit grandkids, campout using phone as hotspot, etc. No method to remotely t

I am looking for some guidance using the Elecraft K3s with P3 and Steppir SDA100. What cables needed and what settings are needed on both the K3s and SDA100 to get the Steppir BigIR to automatically s

I have recently gotten back into CW and I want to get a K3 purely for CW. I have seen plenty of K3/100/AT for under $2000. My code speed is between 13-18 wpm, but I am trying to get proficient so that

I've used the K3/0-mini and RRC boxes quite a bit in a mobile setup. Since 99.999% of my operation was CW I didn't have to deal with many of the idiosyncrasies of the K3/RRC combo. Now the plan is to

Just recently was unable to find any Ports listen in the K3 Utility for my K3S I checked to make sure it was set to Configure-RS232-USB. I also tried another USB cable to the computer and also switche

Looking to buy a K3 in the U.K. if anyone is selling, must have the IO board and low level outputs, prefer USB but the RS232 will be fine. 73 Tim M0AFJ