Last fall one of our K3 radios stopped putting put any power during the last few hours of the CQ WW CW contest. For many reasons I am finally getting back to looking at this failed radio. I swapped in

K3s - Never outside - non smoker - like new. Fully equipped. Including P3 Panadapter - TX Monitor. All details supplied upon request. $3,200.00 US VA2AGW

I have an Elecraft K3S-F purchased at Dayton in 2018. It includes: 100 W upgrade factory installed (KPA3A-F) ATU for K3S factory installed ((KAT3A-F) K3 TCXO 1 ppm factory installed (KTCXO3-F) 2.8 fil

All, Ever since I upgraded the KIO3A board in my K3 s/n 261 to a KIO3B board, I get an intermittent "Illegal Opcode" error, followed by a reboot, on my P3 s/n 688. Both devices are running the latest

I've noticed huge noise on the display when tuning around with the K3 on 6. Not quite as bad on 10. Any cures for this? Thanks Ron N4XD Sent using Zoho Mail

In search of an SP-3 Speaker. Anyone have one they care to get rid of? 73, -- Lee Young, K5LY FOC #2062, CW Ops #1124, FISTS #15371, SKCC #7448 CW Forever!

It appears that the RemoteRig website and DNS Server is offline. No further info is available. I discovered that you can use a personal DNS Server e.g. no-ip for the RRC-1258 / K3 combos. Dan K4FN

Good morning all, On the off chance, does anyone in the UK (or Europe) have a spare KPA3 gold pin repair kit? I can order one direct but the $40 kit costs $80 to ship. Waters & Stanton / Navada don't

Elecraft K3-0 Remote head and manual Remoterig RRC-1258 MKII (2 pcs.) All cables and PS for 1258 (2) User Manual for RRC-1258 MKII $675.00 ins. and delivered Cont. US Pictures on request 73 Thaire W2A

DOH! I checked the key out cable from the 890 with an ohmmeter and sure enough it was almost a short. So I didn't have to hunt long to find the problem - there was a tip-ring-sleeve plug from the 890

Solved! ( https://groups.io/g/Elecraft-K3/message/39064 ) ----------------------------- It's the time for weird things happening. My iPhone 13 played dead today (that's another story) and now my KPA15

First licensed at 14, I'll be 80 in a few months. After my wife's passing, I've lost interest in several things, ham radio being one. I have a K-Line, but it has been turned on less than 10 hours in t

Hello all My K3 was constructed by me in September 2010 and has been used on a number of DXpeditions. However a few years ago it developed an audio fault - no loudspeaker output but OK on headphones.

Hello! I have a KRX3 sub receiver I'm going to install into my K3. I have all the instructions, etc. but wondered if anyone on here had some advice on what to look out for, or do's and don'ts? Also an

Hello, Does anyone know if the cable which carries data from the Panadaptor Power Sensor, to the W2 Wattmeter, can be replaced with a standard CAT 5 Ethernet cable? -- 73, and thanks, Dave (NK7Z) http

Current setup. K3 with P3 early serial. Back to factory for complete update. Gold Pins etc. Today K3 shut down. Found blown 15 amp fuse in ground side of power supply cable Power supply is MFJ 4035MW.

Shuts down showing overdrive with 35w drive Anyone experienced this?

Searched the K3 manual and not finding the way to change the callsign show on startup .. not that it matters to operation. Just curious if I’m missing some setup procedure or program. Joe K9UR

I sold my Kenwood TS890 and have a keying and frequency data cable for a Elecraft amplifier. This also works with Kenwood 590 and 990. $45 shipped.

I have a K3 (S/N 2XXX) which has had no mods, but has sub receiver, DVR, lots of filters, etc. I was thinking of adding the KSYN3A (found one used), but a friend tells me I have to have one each for m