Hi Jim, Also make SURE that the RS-232 connection is DIRECT to the K3, not through the P3 (if there is one there) or any other component. If you're using a USB to RS-232 dongle, try another USB port,

Nope. It's a feature I've asked for several times with no reply; which is either lack of interest or it's not possible (because I KNOW they listen here and in direct email). You CAN use an app to turn

Because you will not be sending or receiving the best signal you can. “Using Data A turns OFF audio processing and NR functions which cause distortion on both TX and RX. Using USB/LSB does not.” Rick

Data A is for ANY digital mode that requires audio, AFSK RTTY, FT8, PSK etc etc. You can use Data A for any digital mode requiring audio with HRD. Using Data A turns OFF audio processing and NR functi

If HRD transmits on other modes, it will transmit on Data mode as well, something is not right in your set up. VOX is *not* required with data modes in HRD if properly set for a K3. It is required for

Try at 19200 (or other speeds). If I recall correctly, you can 'talk' to the P3 at whatever speed you wish, but it talks to the K3 at 19200 only. On the other hand if you're not serial connecting the

If you choose to print it (harder to search for trivia but old school still rocks); use at least 22 bond paper (takes a beating better than the typical office paper) and put it into a folder, WITH you

Gene, (Small rabbit trail) And a GREAT showing that trip made! Thanks for the many contacts (21 confirmed), the treats were on 160M (500 watts, inverted L) and the shocker was on 60M (100 watts into a

Yes, up to one extension or the timing gets skewed and problems happen. That's what I've been doing. Rick NK7I

Bob, You must remember that lists like this rarely sing the praises of any piece of soft/hardware. The emails on such lists are HEAVILY biased towards problems, complaints and whining. My Elecraft gea

You'll find that the audio won't be sent though the transmit is enabled with WSJT-X. There is a logging issue (it says it's logging but doesn't), that's happened a few times now (the DX writes me and

Or if you remote op while traveling, it’s convenient to keep in touch with your home repeater/s. Done that too. Rick NK7I Smell Czech corruptions are inevitable

There is a files section on groups.io, if enabled. Rick NK7I Smell Czech corruptions are inevitable

If only on one band, tuned input circuit, $$ not awful. If all bands, the finals, $$ between ok and ouch. Don’t forget the shipping insurance, but on the plus side; it’ll get all the updates. Rick NK7

I've seen USB fail like that under RFI conditions (so I try hard to not use it in the station). Sometimes, a complete power down (plugs pulled) and reboot is required to bring that USB device 'back to

1) No, only if you put the amp in standby. 2) Yes, set the tune wattage to a low enough value that it supplies the tuner with enough, but doesn't cause the amp to blow out the tuner (set the TUN PWR t

From memory (variable these days), the K0 (kay zero) command turns off the K3. To save power, there is no power on command (the cpu would have to be fully awake and that would raise consumption). I ha

Mark, What was clear is that you asked if bandwidth storage could be done within the K3 memory which is limited to mode and frequency (VFO B, offset, and PL tones in some uses). That was mode, not ban

You can use the WSJT-X program itself to change bands and the mode to DATA using the drop down on the left side, middle window where it displays the band in use (not the frequency). Then leave the DAT

I put a copy of the cert in Dropbox, to pull from on three computers, each with TQSL installed. No issues at all. (I export my log there too, for the same reasons plus cloud backup.) There have been T