As mentioned earlier, we are moving the company to a larger facility this week. We now have Olivia and Madelyn in our sales group up at the new office and our new phone numbers are now active. Our new

Thank to the huge response by our customers this year (on the K3 and all of our other products) we are moving the company to a larger facility. 2x the space for about the same cost as where we are now

> --- In Elecraft_K3@..., "joe_word" joe_word@ wrote: > > > > Any word on when the P3 will be available and the price? I am waiting > on purchasing a K3 until I have this info. > > Joe N9V

--- In Elecraft_K3@..., "joe_word" wrote: > > Any word on when the P3 will be available and the price? I am waiting on purchasing a K3 until I have this info. > Joe N9VX Hi Joe, We were ta

The K3 will not shut itself off unless the power voltage drops too low. If you are driving a low impedance load, that in turn causes the K3 to draw more current. That may exceed your power supply's cu

CORRECTION - I have some egg on my face. I misread our internal release date notes for the Rev C DSP board. Here is the correct Date and S/N Information: We started shipping the latest DSP boards, Rev

Here is an update to my earlier message that includes an order link etc. We started shipping the current DSP boards, Rev C, approximately March 6th, 2009. Any K3 DSP board Rev C or later will have the

Hi Mike, We started shipping the latest DSP boards, Rev C, approximately March 6th, 2009. Any K3 DSP board Rev C or later will have extended low end audio response enhancement. A picture of the Rev la

Important: All new K3s already have a DSP board with the audio low freq response changes made. This has been so for a number of months. You do not need to make any mods to the DSP board. I do recommen

Hi Henry, The ARRL phase noise plot in their reviews is measured on TX from the transmit signal, so it encompasses both RX noise and any additional TX noise that might be added in. Its referenced as p

I just updated the table of ARRL test numbers on our web site with the phase noise measurement from their review. At 4kHz it was actually -133 dBc on the chart. It then slopes down to -155 to -160 dBc

Hi, I've had several requests to update status on our price changes. The date will be in a week and a half - 9/15 or 9/16. (Lisa was out this week. We need to meet and confirm the change amounts, modi

Heads up! - We want to give an advance notice to our loyal Elecraft K3 Yahoo list members. We will be increasing prices a small amount on the K3 and our other products in early September. If you have

Its only used for internal programming of the front panel during manufacture. It is not used for anything else at this time. 73, Eric WA6HHQ

I've also uploaded this P3 photo to the Elecraft_K3 group's photos section, in the P3 folder. Eric

Here's a larger shot of the P3 and K3 we took in the room last night after the show. (You may need to re-size it in your browser.) http://www.elecraft.com/K3/pics/P3%20w%20K3%20a.JPG Please excuse any

Generally I personally find the 1.8 kHz filter way too narrow for most of my regular SSB use. It -is- useful though for the extreme QRM conditions during contests. I much prefer the 2.7 or 2.8 kHz fil

Yes - point and click tuning is included in the P3. You can move a cursor onto a signal on the color display and then click the knob in to select that freq as the center freq for the K3. Bingo! - you

The K3 crystal filters are absolutely an important part of its strong signal handling capability. Yes, the DSP provides filtering down to 50 Hz and is more than sufficient for rejecting interfering of

Not yet. we wil lhave an interest sign up list though so we can contact you when we do plan to start taking orders. 73, Eric