To Alan (N1AL): Thank you ever so much for the info. I am waiting for a used K3 to arrive soon and I am already thinking about using my Perseus SDR as a no cost "panadapter" connected at the IF OUT

- Elecraft P3 TXMon Adapter UNUSED! Brand New Unused Elecraft TXMon adapter for Elecraft P3. Previous owner never had the opportunity to install in their P3. Sealed module, and hardware bag, complete

Assuming a reasonably late-model K3 or an older one that has the IF out modification, the gain from the K3 antenna to the IF output is approximately -6 to -7 dB with the K3 preamp off and about +4 to

How did you use it and how frequently did it fail Joe? Did you have a logger running on a PC and use it to activate the DVK using the appropriate macro commands? If this is true, I would test

Can someone please measure the conversion gain (in dB) of an Elecraft K3 from ANT to IF OUT (with 50 Ohm load on the IF OUT port) on any or preferably all HAM bands? I can also do with data measured

Hi Keith V 05.67. It seems to be the latest according to your homepage. Joe, OZ0J Fra: Elecraft-K3@groups.io <Elecraft-K3@groups.io> På vegne af Keith_WE6R Sendt: 12. oktober 2020

Hi Joe, what DVR Firmware do you have? Turn on radio, config menu "FW REVS", rotate VFO A all the way clockwise. Keith WE6R Elecraft K3 Tech

I once had the same problem. UK support suggested checking proper seating of all Inter-board connectors. Until my next serious contest with it I’m not sure if it is fixed yet. Keep you posted. 73,

Hi I have an Elecraft K3S with the KVDR3 installed. I used it a lot during the SAC SSB Contest this weekend. When running the DVR in repeat the DVR decided to send empty CQ (TX on but no

Thanks Bob I tried it and surprisingly if I touch the power knob the power display jumps up to the 7 watts TUN PWR setting, but then immediately drops back down to 0.0. From the manual: TUNE Power

I'm putting my K3 (Serial# 6384) up for sale. Do not reply to the list, I will only reply to direct emails if you convince me you are serious and then we set up time to talk on the phone (any cc'd

After you press TUNE and the TX LED is on, then adjust the PWR knob to your desired power value to tune. 73 Bob, K4TAX

Bill It's not a tuner issue. On "tune" my K3 reports 7 watts out on all bands except 30 m, where it reports 0.0 watts out. The power meter confirms no output. -- 73 Bob KD8CGH

Hello, A update from my site. After some more test last week I got completely confused. Sometimes it worked, than it stopped. I completely removed the software from my laptop: mmtty, n1mm, microham,

You don’t mention what tuner you are using. I use a remote tuner and find a similar situation, MFJ998 in a patio box. When it doesn’t tune, I remove power for seconds plug back in and then tuner

I have a remote tuner so I hold the "tune" button to send a low power carrier for the tuner to operate. The tune power is set by the config parameter TUN PWR. This works great for every band but 30 m,

Figured it out - Data Mode was set incorrectly on 10MHz! Chris Cox, N0UK chrisc@...

Thanks Jerry for your advice, I decided to go first class and ordered a shipping box ($50.00 include shipping) and put the transformer back into the unit without reconnecting it. I am

Hello Joe (W4TV), I did the simulation of the AF filter (p. 35). Please find the result attached. 73, Robert

Lou, Check with Elecraft first and ask for a support person first before shipping the transformer. They will tell you if they need it in order to repair your unit. Most cases they do not.