This is probably a "101" level thing check, but can you confirm that the sub-RX setting of "MAIN" has stuck? It's happened to me several times in the past that it's changed to AUX seemingly on its

Hi All, I need some suggestions on where to start trouble shooting. I looked at Nabble and I have checked all that is listed there and no luck. The sub receiver was working perfectly. I took the

OK Ray, will ship tomorrow. Got your address from previous email. -- 73, Bob Patten, N4BP Plantation, FL E-Mail : n4bp@... Website:

Bob......... That one came in...... I will get the wife to paypal the $25.00 thanks Ray

On Thu, Mar 21, 2019 at 6:24 AM Bob Patten <n4bp@...> wrote: Ray, WA6VAB Appears you're not getting my emails. Deal is OK with added $5 for shipping. PayPal if you can to n4bp@.... -- 73, Bob

Ray, WA6VAB Appears you're not getting my emails. Deal is OK with added $5 for shipping. PayPal if you can to n4bp@.... -- 73, Bob Patten, N4BP Plantation, FL E-Mail

I made a couple of detailed videos on this topic... the first one is specific to the 2K-FA and building your own interface cable and the second one is sharing the K3/S CAT feed across multiple

Fixed a work around for the K3 Utils port selection.. The problem occurred only in K3 Utilities. Worked OK with Win4KSuite & HRD but not with K3 Utilities. I also have additional ports assigned to

Yes it is, thats how I do it. I found lots of designs for connecting K3 to the spe but no k3s to the spe, so I had to work it out myself I just needed a screened ethernet cable which i chopped one end

I recently upgraded my old K3 with a KXV3B Xverter I/O, RX Ant I/O module and no longer need the KXV3. If anyone can use it, I will at least need to collect shipping cost. A small donation wouldn't

Using FTDI latest drivers. 2 years no problems. Starting HRD with same settings as in the past. No Problems. Close HRD - Start K3 Utilities and there are no ports displayed in the drop down. Restart

I've had a few folks request the wiring diagram via email. I'm good on QRZ, but I do have an ARRL address for those that would like a copy of my wiring diagram. Thanks! K4HYJ

John Thanks for the reply. It is the K3S end, I am not sure what to do. I did find a RS232 -> RJ45 cable for my K3S, so I expect that I can use that. - Joe OZ0J Fra:

KPA1500 Remote will indeed turn the amp on and off. Yes, it takes some screen space but that is well worth it to avoid “flying blind” running 1500 watts with no indication of what’s going on

There are times I prefer to operate without the amp when operating remote. Since my eight channel relay switcher can accommodate the function, makes sense to me to use it for powering the amp on/off

You have to use the DB15 acc jack. -John NI0K

Using the USB connection, you can turn the KPA1500 off and on as well has control most functions. Used it over the last 6 weeks running remote from Florida back to my station in Illinois. Haven't

Hi I do have an Elecraft K3S with a RJ45 plug for the RS232. I would like to connect my SPE Expert 1,3K FA so the K3S sends band data to the Expert PA. I will connect the K3S to my

Bob, Use the 12v switched 1.0A Max RCA phono jack on the back of the K3 and connect it to the Rem phono jack on the KPA1500. You will need a male - male cable. With this setup, whenever you turn on

As far as I understand it the remote software will not turn on the amplifier. I am not using a K3 therefore I cannot use the 12v jack to connect to the remote jack on the 1500. What I thought I would