I now have two K3's (not S, just originals). I am replacing my FT-991, which was my dedicated digital radio with my second K3. I figured it would be a no brainer to get digital to work. So far it has

There is a description in the P3 manual about S levels (see page 17). The K3 S-meter reads an average energy for the whole bandpass, the P3 is reading for the individual bin (column on the pan

I recently installed the SVGA option in my P3 and noticed that the S-Meter scales on the P3 and SVGA do not match the S-Meter scales on the K3S radio. I probably paid no attention to this before.

Hi I have a K3s with a internal 2m transverter. Can I loop the 28Mhz IF from the transverter thought the rear panel RX Ant in and out BNC's while on 144 Mhz. Also can this be switched using the Rx

Geoff, You are correct. I determined that when the RemoteHams server disconnects for some reason then the K3-mini goes into terminal mode when it attempts to connect to the server. The fix is to

Expected behaviour, Scott! The K3/0 mini only knows TERM mode, it's not a full transceiver. ;-) TERM will be shown during connection to the remote side. No way/need to avoid it, normal

Hi Scott - I get the K3/0 mini showing TERM if the 1258s are not connected via the internet. I don't use Remotehams.com with my K3/0 mini but I suspect the TERM indication is caused by the same

I am using the K3-mini to remotely operate my K3 via RemoteHams.com. Occasionally, the K3-mini starts in the TERM mode. I select the NORM mode by holding the [MENU] buttom for 5 seconds and then

I purchased a USB keyboard and plugged it into my P3. Hoping to use this setup for RTTY I set up some text files in several memories. They work fine. However, the Help menu indicates Ctrl-T will

I have my headset/ headphones on the external speaker with a volume control to reduce the level. No switching needed just grab the phones when desired and go. Phone volume slightly louder than

I have programmed M2 to toggle the speaker on and off on my K3. Surely the S model will do that. -Robby HP3/VY2SS

I would suggest the most simple fix; do not use 12m, with the amp turned on, and you will have no problem. Keep using it and you Might have More problems. ;) There is a frequency counter built in the

My KPA500 has a bum 12m LPF. I have the means to repair it, but in the meantime, is there any way to adjust the band selection algorithm so that when I QSY to 12m on the K3, that the KPA500 goes to

Chuck, Be like me, if I hear something I don't like to hear I take my hearing aids out. :) Dale, K9VUJ

I was a little troubled by the feel of the VFO when I first got my K3 seven years ago. However, after I adjusted the tension to about the weight of the knob it was acceptable to me. Over time I

Thanks again for the recent responses. As I said earlier, the VFO-A knob issue is not a showstopper. The radio is great in all other respects, a definite keeper for me. I was just wondering if anyone

Hey Mike, Yep, nothing is perfect, but if it all comes down to the feel of the tuning knob then we must not have much to complain about heh? Dale, K9VUJ

Tom, The KAT-500 160 meter segments for the DX portion are: 1800-1810 10Khz 1810-1816 6Khz 1816-1824 8Khz 1824-1832 8Khz 1832-1850 18Khz Ralph W1ZK

This knob and or encoder thing comes up every now and then. Mine is ok but it's not a perfect rotation. 73 Mike R Find me on "Zello", a walkie talkie or handi talkie type app. I'm listed as KE5GBC.

Neither do I, but I don't use much if any friction, very smooth tuning almost as good as my former 7800 which I don't own anymore. A weighted knob might help those with deftness in their