Date   

Re: [Elecraft_K3] Re: Travel advice

VE9AA - Mike
 

That site is blocked here Joe (work) but a google image search produced black bags that look vy similar to mine. (but mine is tan)

I cant say for sure but the foam inserts on tbe w0yk page look like mine too.(but mine are grey)

I would think it would be almost as good as a pelican, but u cud carry it on. Nor sure u cud carry-on a pelican?

Mike ve9aa


K3 Utility 1.16 for Mac

trevor clapp
 

I have just got my Kpod and brilliant it is too.

Any ideas when 1.16 will be available for us Mac users so I can upload macros to all 16 macro slots as opposed to just the 8?

Trevor



Re: [Elecraft_K3] change the processor board?

ab
 

I went the simplest possible route, just wanting to exercise the connectors on the faceplate a little bit by removing the bottom two screws on the faceplate and the one screw on each end plate.  Just enough to be able to use a screwdriver blade to move the faceplate connectors out about 1/8" using the normal 'pry access points'.  Moved the faceplate back and forth a couple of times and then reseated the faceplate and so far I haven't been able to reproduce the power drop issue on 75/80 meters so that may have done it.  I will know soon enough when I power up from a cold start if the other 'freq jumping' issue is gone too.  Off to Colorado on business now and we'll play with it next weekend.  Sure hope that was it.  Will update in about a week.


Re: [Elecraft_K3] change the processor board?

William Conkling <bconk75@...>
 

See the manual about calibrating the Front Panel and PA temperature readings. 

...nr4c. bill


On Aug 21, 2016, at 6:26 PM, skyviewcharles@... [Elecraft_K3] <Elecraft_K3@...> wrote:

 

Thanks for every response.  It is such a great design that the idea that it's simply a dirty connection really appeals to me.  Plus with the temperature related behavior of the one bug it makes good sense.  So I will try cleaning the contacts and let you know how it goes.  S/N is 4523 and it's been a well behaved unit up until a few months ago.  When in doubt clean the connections, reload the firmware and we shall see!

Thanks!  73 N6AF


Re: [Elecraft_K3] Re: Travel advice

Joe Subich, W4TV
 

Sounds like one of Rose Kopp's cases:
<ElecraftCovers@gmail.com>
<https://www.smugmug.com/gallery/n-mX9LCZ>

73,

... Joe, W4TV

On 8/21/2016 5:28 PM, ve9aa@nbnet.nb.ca [Elecraft_K3] wrote:
Steve,


My K3 came in a roundabout kind of way from Gary, VE1RGB, who had it in a tan w/ green trim, soft, padded canvas (or denim?) carry-on bag with an Elecraft logo on it. Inside the bag are 2 foam w/ plastic cutouts that are custom fit to the front and rears of the K3 protecting it from all but the most violent of hits. I had it literally squeezed into a MINI COOPER for my recent trip to VO1TTT (27hrs one way) and for a week's vacation afterwards and it survived just fine.


It's not much bigger than a laptop bag and I am sure would qualify as check in size. (aprox 14"x14"x7")


I have no way of determining if this is/was an Elecraft accessory, but someone may read this and could verify.


Mike VE9AA..........p.s.-nice job from VY2TT !


Re: [Elecraft_K3] change the processor board?

ab
 

Thanks for every response.  It is such a great design that the idea that it's simply a dirty connection really appeals to me.  Plus with the temperature related behavior of the one bug it makes good sense.  So I will try cleaning the contacts and let you know how it goes.  S/N is 4523 and it's been a well behaved unit up until a few months ago.  When in doubt clean the connections, reload the firmware and we shall see!

Thanks!  73 N6AF


Re: Travel advice

VE9AA - Mike
 

Steve,


My K3 came in a roundabout kind of way from Gary, VE1RGB, who had it in a tan w/ green trim, soft, padded canvas (or denim?) carry-on bag with an Elecraft logo on it.  Inside the bag are 2 foam w/ plastic cutouts that are custom fit to the front and rears of the K3 protecting it from all but the most violent of hits.  I had it literally squeezed into a MINI COOPER for my recent trip to VO1TTT (27hrs one way) and for a week's vacation afterwards and it survived just fine.


It's not much bigger than a laptop bag and I am sure would qualify as check in size. (aprox 14"x14"x7")


I have no way of determining if this is/was an Elecraft accessory, but someone may read this and could verify.


Mike VE9AA..........p.s.-nice job from VY2TT !


Re: [Elecraft_K3] Travel advice

rafox3
 

Carry do not check preferably as carry on ever if wrapped in  so
Robert 
NM2D 



Sent from my Samsung device


-------- Original message --------
From: "'Stephen Bloom' sbloom@... [Elecraft_K3]"
Date: 8/21/16 21:45 (GMT+00:00)
To: Elecraft_K3@...
Subject: [Elecraft_K3] Travel advice

 

Hi all:

 

I do a fair amount of travel for contests.  I have a couple of Pelican cases …each large enough for either a K3 or a KPA500 and accessories.  They are of course too large to take as carryon, and normally I just check them, without incident.

 

My next trip is to Suriname, with a change of planes and airlines ..(meaning rechecked baggage) in Trinidad.  I’ve been told in no uncertain terms that putting the K3 in checked luggage for this is a doubleplus ungood idea.  Luckily for this trip, I’ll need only a K3 and a Microkeyer, but I am wondering …is there a Pelican case (or equivalent) out there, that is small enough to qualify as carry on, but large enough to hold a K3?

 

Thanks/73

Steve KL7SB

 

p.s.  I also thought about just shipping the gear ahead of time …I was also told that was a bad idea.

 


Travel advice

Stephen Bloom
 

Hi all:

 

I do a fair amount of travel for contests.  I have a couple of Pelican cases …each large enough for either a K3 or a KPA500 and accessories.  They are of course too large to take as carryon, and normally I just check them, without incident.

 

My next trip is to Suriname, with a change of planes and airlines ..(meaning rechecked baggage) in Trinidad.  I’ve been told in no uncertain terms that putting the K3 in checked luggage for this is a doubleplus ungood idea.  Luckily for this trip, I’ll need only a K3 and a Microkeyer, but I am wondering …is there a Pelican case (or equivalent) out there, that is small enough to qualify as carry on, but large enough to hold a K3?

 

Thanks/73

Steve KL7SB

 

p.s.  I also thought about just shipping the gear ahead of time …I was also told that was a bad idea.

 


Re: [Elecraft_K3] Popping Noise

w3qt_mike
 

Thanks, Knut, and others who replied.  Appreciate the feedback.

73,
Mike, W3QT

On 8/21/2016 3:10 PM, ab2tc@... [Elecraft_K3] wrote:
 

Hi,


Yes, there is a pop when turning power on and another when turning off. Truth is that all solid state audio amplifiers with an output that is coupled with a capacitor (almost always the case with smaller amplifiers) exhibit this. I do not think you have to worry about speaker damage.

AB2TC - Knut


---In Elecraft_K3@..., wrote :

I have not had this happen with my K3s or my older K3.

Dale, K9VUJ


On 20, Aug 2016, at 14:22, Mike Morrow w3qt@... [Elecraft_K3] <Elecraft_K3@...> wrote:



Mike,

I'm a little concerned about possible cone damage. That's why I am wondering if others are hearing the same thing.

73,

Mike, W3QT


On 8/20/2016 2:43 PM, mikerodgerske5gbc@... [Elecraft_K3] wrote:
> I think my k3 does that. Didn't know it was a problem.
>
> 73
> Mike R
>
> Find me on "Zello", a walkie talkie or handi talkie type app. I'm listed as KE5GBC. I'm mostly on late at night.
>
> On Aug 20, 2016, at 12:05 PM, "w3qt@... [Elecraft_K3]" <Elecraft_K3@...> wrote:
>
>>
>> I'm running a K3s and have a popping noise through the external speaker when turning on the rig and to a lesser extent when turning it off. I recently changed speakers, thinking maybe a change would help, but the issue is still there. I'm currently using a TenTec 307B speaker. I've checked the cabling and terminals and tried a few different shunt capacitors across the speaker termnals. Does anyone else have a similar issue? Any ideas what to try next? Thanks.
>>
>> 73,
>> Mike, W3QT
>>
>>
>>


Re: [Elecraft_K3] change the processor board?

Nick Lelyak <nicklelyak@...>
 

Hi Chas,
I had exactly the same problem as you described first bug.
Cleaning front panel connectors didn't help.
I had to send the radio to Elecraft.
They found corrupted Front Panel Flash.
Reloading Front Panel Flash fixed the problem.
At the same time they fixed some other issues they found and replaced front panel and KPA3 connectors for gold pins (for free)

73, Nick VE3FJ

On Sun, Aug 21, 2016 at 12:50 PM, skyviewcharles@... [Elecraft_K3] <Elecraft_K3@...> wrote:
 

My K3 now has two distinct bugs.  One bug that's been present for several months occurs during the first few minutes of warm-up (until the indicated FacePlate FP temperature is above about 27C), when I turn the VFO control the relays click and the freq jumps to an arbitrary and non-standard value such as 246.200 MHz.  Yes, I wrote two hundred and forty six point two Megahertz.  The second bug is more recent and highly frustrating.  Only on 75/80 meter band does this occur.  After about one minute of transmission the output power will drop back from 100 W down to about 35 W (CW output for example or simply pressing XMIT to send a constant carrier) .  The only way to clear this condition is by turning off the rig and turning it back on.  This is when running into a known good 50 Ohm dummy load.  It's not heat related, it's not the SWR foldback function kicking in.  Nothing like that.  It appears to be a "control related bug'.  When it is limited to about 35 W out (Bird Wattmeter), adjusting the power out control indicates "100 W" but it's outputting about 35 Watts.  All other bands do not do this while the rig is confirmed in this trouble condition on 75/80 meters.  In other words when the power is limited to about 35 W out on 75/80 meters I confirmed a proper 100 W out on all other bands.  Very strange to be limited to the one band.

My question to the K3 owners out there - have any of you had similar apparent processor related bugs and simply shot gunned the repair by changing out the main board that contains the uP?  That may be less expensive than pursuing the formal evaluation/repair approach.

Thanks for any suggestions.  I know I can send it to the K3 hospital but it's not covered by Obamacare (yet anyway) so I'm looking at other possible approaches.  Anybody been down this buggy road?

73 N6AF Chas



Re: [Elecraft_K3] Popping Noise

ab2tc
 

Hi,

Yes, there is a pop when turning power on and another when turning off. Truth is that all solid state audio amplifiers with an output that is coupled with a capacitor (almost always the case with smaller amplifiers) exhibit this. I do not think you have to worry about speaker damage.

AB2TC - Knut


---In Elecraft_K3@..., <dj2001x@...> wrote :

I have not had this happen with my K3s or my older K3.

Dale, K9VUJ


On 20, Aug 2016, at 14:22, Mike Morrow w3qt@... [Elecraft_K3] <Elecraft_K3@...> wrote:



Mike,

I'm a little concerned about possible cone damage. That's why I am wondering if others are hearing the same thing.

73,

Mike, W3QT


On 8/20/2016 2:43 PM, mikerodgerske5gbc@... [Elecraft_K3] wrote:
> I think my k3 does that. Didn't know it was a problem.
>
> 73
> Mike R
>
> Find me on "Zello", a walkie talkie or handi talkie type app. I'm listed as KE5GBC. I'm mostly on late at night.
>
> On Aug 20, 2016, at 12:05 PM, "w3qt@... [Elecraft_K3]" <Elecraft_K3@...> wrote:
>
>>
>> I'm running a K3s and have a popping noise through the external speaker when turning on the rig and to a lesser extent when turning it off. I recently changed speakers, thinking maybe a change would help, but the issue is still there. I'm currently using a TenTec 307B speaker. I've checked the cabling and terminals and tried a few different shunt capacitors across the speaker termnals. Does anyone else have a similar issue? Any ideas what to try next? Thanks.
>>
>> 73,
>> Mike, W3QT
>>
>>
>>


Re: [Elecraft_K3] change the processor board?

harry latterman <harrylatterman@...>
 

Chas

What is the S/N of your radio... As mentioned you might have a older one without the gold contacts. I have two K3's and one is like that. I had TX die on me and once I pulled the AMP out and clean the contacts it has been working fine ever since... In you case I suspect it is the front panel board. Easy...well not really easy.. fix will be to pull the front panel off and clean contracts and plug it back in.. The reason I said not really easy is there are a lot of pins connecting the front panel and DSP board to the main board.  I was give and dead K3 and had fun bringing life into it. In my case I had to send the front panel+DSP board in since I had 5 push buttons that did not work. Less then 2 weeks later I got boards back and completed the repair, which lead me to the pins on the AMP module...which are tinned and not gold..

2 cents  back under my rock...Good luck and hope this suggestion helps

73 Harry K7ZOV



From: "skyviewcharles@... [Elecraft_K3]"
To: Elecraft_K3@...
Sent: Sunday, August 21, 2016 9:50 AM
Subject: [Elecraft_K3] change the processor board?

 
My K3 now has two distinct bugs.  One bug that's been present for several months occurs during the first few minutes of warm-up (until the indicated FacePlate FP temperature is above about 27C), when I turn the VFO control the relays click and the freq jumps to an arbitrary and non-standard value such as 246.200 MHz.  Yes, I wrote two hundred and forty six point two Megahertz.  The second bug is more recent and highly frustrating.  Only on 75/80 meter band does this occur.  After about one minute of transmission the output power will drop back from 100 W down to about 35 W (CW output for example or simply pressing XMIT to send a constant carrier) .  The only way to clear this condition is by turning off the rig and turning it back on.  This is when running into a known good 50 Ohm dummy load.  It's not heat related, it's not the SWR foldback function kicking in.  Nothing like that.  It appears to be a "control related bug'.  When it is limited to about 35 W out (Bird Wattmeter), adjusting the power out control indicates "100 W" but it's outputting about 35 Watts.  All other bands do not do this while the rig is confirmed in this trouble condition on 75/80 meters.  In other words when the power is limited to about 35 W out on 75/80 meters I confirmed a proper 100 W out on all other bands.  Very strange to be limited to the one band.

My question to the K3 owners out there - have any of you had similar apparent processor related bugs and simply shot gunned the repair by changing out the main board that contains the uP?  That may be less expensive than pursuing the formal evaluation/repair approach.

Thanks for any suggestions.  I know I can send it to the K3 hospital but it's not covered by Obamacare (yet anyway) so I'm looking at other possible approaches.  Anybody been down this buggy road?

73 N6AF Chas



Re: [Elecraft_K3] change the processor board?

dalej <dj2001x@...>
 

Never had the trouble on either of my 2 K3’s.

Have you had the covers off and checked all the plugs and readily accessible connections?

Yes, calling Elecraft support is a good idea. They might have some good ideas for you to try.

73
Dale, K9VUJ


My question to the K3 owners out there - have any of you had similar apparent processor related bugs

73 N6AF Chas


K3 Key Out - Let the Metal out of an IRFI630G MOSFET

Max NG7M
 

NG7M Max here... raising my hand with no shame! I pulled off frying the beefy Power MOSFET used on the K3 Key Out.  On the Schematic / PCB, it's Q3.  It's clear I ran 5+ amps through it.  This post might help someone else, because I didn't find any other posts in my short search where someone else was 'dumber than a bag of hammers' like me... maybe they were smarter and didn't fess up to it! :) (Jim W7CT, you can't post.  I'm not in the mood to take any crap from you! LOL!)


Here is a nice picture of what it looks like on an IRFI630 when you do this: (nice crack and molten metal ooz)


So my real question is... is there anything else to worry about?  I can't see anything else on the PCB around Q3 that appears to be funky.  I just ordered up 2 more 630's from mouser so I'll be able to fry another if so desired.  My K3 is working it appears, minus the keying.  It's not fun when you smell the smoke and it's coming from inside of your K3 case.  Needless to say, I dropped a few choice words.


For reference, which the next poor slob find helpful , here is the replacement on Mouser:


http://www.mouser.com/Search/ProductDetail.aspx?R=IRFI630GPBFvirtualkey61370000virtualkey844-IRFI630GPBF


So if you are still reading, what I was working on at my QTH where I run the NC7J DX Cluster and NC7J Skimmer Server was a keying interface so when I key my K3 it would cut the power to a couple of preamps I'm running on the antenna setup with the QS1R receiver.  I obviously have some issues with my hack design.


Please be gentle if you respond. ;)


Max NG7M




Re: [Elecraft_K3] change the processor board?

Geoffrey Downs
 

If your K3 is an older one that doesn’t have gold pins for the front panel, it might be oxidation on some of the pins. It might not be, of course, but it may be worth checking by removing the front panel, cleaning the pins and putting it back, maybe even with a little Deoxit or Contralube on them. I’ve not had exactly the same faults with my senior K3 (#266) but twice over its 8+ yr life have had esoteric happenings relating to frequency, power or error messages that were cured by doing this.
 
GL es 73
 
Geoff
G3UCK
 

Sent: 21 August, 2016 5:50 PM
Subject: [Elecraft_K3] change the processor board?
 
 

My K3 now has two distinct bugs.  One bug that's been present for several months occurs during the first few minutes of warm-up (until the indicated FacePlate FP temperature is above about 27C), when I turn the VFO control the relays click and the freq jumps to an arbitrary and non-standard value such as 246.200 MHz.  Yes, I wrote two hundred and forty six point two Megahertz.  The second bug is more recent and highly frustrating.  Only on 75/80 meter band does this occur.  After about one minute of transmission the output power will drop back from 100 W down to about 35 W (CW output for example or simply pressing XMIT to send a constant carrier) .  The only way to clear this condition is by turning off the rig and turning it back on.  This is when running into a known good 50 Ohm dummy load.  It's not heat related, it's not the SWR foldback function kicking in.  Nothing like that.  It appears to be a "control related bug'.  When it is limited to about 35 W out (Bird Wattmeter), adjusting the power out control indicates "100 W" but it's outputting about 35 Watts.  All other bands do not do this while the rig is confirmed in this trouble condition on 75/80 meters.  In other words when the power is limited to about 35 W out on 75/80 meters I confirmed a proper 100 W out on all other bands.  Very strange to be limited to the one band.

My question to the K3 owners out there - have any of you had similar apparent processor related bugs and simply shot gunned the repair by changing out the main board that contains the uP?  That may be less expensive than pursuing the formal evaluation/repair approach.

Thanks for any suggestions.  I know I can send it to the K3 hospital but it's not covered by Obamacare (yet anyway) so I'm looking at other possible approaches.  Anybody been down this buggy road?

73 N6AF Chas




Avast logo

This email has been checked for viruses by Avast antivirus software.
www.avast.com



change the processor board?

ab
 

My K3 now has two distinct bugs.  One bug that's been present for several months occurs during the first few minutes of warm-up (until the indicated FacePlate FP temperature is above about 27C), when I turn the VFO control the relays click and the freq jumps to an arbitrary and non-standard value such as 246.200 MHz.  Yes, I wrote two hundred and forty six point two Megahertz.  The second bug is more recent and highly frustrating.  Only on 75/80 meter band does this occur.  After about one minute of transmission the output power will drop back from 100 W down to about 35 W (CW output for example or simply pressing XMIT to send a constant carrier) .  The only way to clear this condition is by turning off the rig and turning it back on.  This is when running into a known good 50 Ohm dummy load.  It's not heat related, it's not the SWR foldback function kicking in.  Nothing like that.  It appears to be a "control related bug'.  When it is limited to about 35 W out (Bird Wattmeter), adjusting the power out control indicates "100 W" but it's outputting about 35 Watts.  All other bands do not do this while the rig is confirmed in this trouble condition on 75/80 meters.  In other words when the power is limited to about 35 W out on 75/80 meters I confirmed a proper 100 W out on all other bands.  Very strange to be limited to the one band.

My question to the K3 owners out there - have any of you had similar apparent processor related bugs and simply shot gunned the repair by changing out the main board that contains the uP?  That may be less expensive than pursuing the formal evaluation/repair approach.

Thanks for any suggestions.  I know I can send it to the K3 hospital but it's not covered by Obamacare (yet anyway) so I'm looking at other possible approaches.  Anybody been down this buggy road?

73 N6AF Chas


Re: [Elecraft_K3] Popping Noise

dalej <dj2001x@...>
 

I have not had this happen with my K3s or my older K3.

Dale, K9VUJ

On 20, Aug 2016, at 14:22, Mike Morrow w3qt@comcast.net [Elecraft_K3] <Elecraft_K3@yahoogroups.com> wrote:



Mike,

I'm a little concerned about possible cone damage. That's why I am wondering if others are hearing the same thing.

73,

Mike, W3QT


On 8/20/2016 2:43 PM, mikerodgerske5gbc@yahoo.com [Elecraft_K3] wrote:
I think my k3 does that. Didn't know it was a problem.

73
Mike R

Find me on "Zello", a walkie talkie or handi talkie type app. I'm listed as KE5GBC. I'm mostly on late at night.

On Aug 20, 2016, at 12:05 PM, "w3qt@comcast.net [Elecraft_K3]" <Elecraft_K3@yahoogroups.com> wrote:


I'm running a K3s and have a popping noise through the external speaker when turning on the rig and to a lesser extent when turning it off. I recently changed speakers, thinking maybe a change would help, but the issue is still there. I'm currently using a TenTec 307B speaker. I've checked the cabling and terminals and tried a few different shunt capacitors across the speaker termnals. Does anyone else have a similar issue? Any ideas what to try next? Thanks.

73,
Mike, W3QT



Re: [Elecraft_K3] Popping Noise

w3qt_mike
 

Mike,

I'm a little concerned about possible cone damage.  That's why I am wondering if others are hearing the same thing.

73,

Mike, W3QT


On 8/20/2016 2:43 PM, mikerodgerske5gbc@... [Elecraft_K3] wrote:
 
I think my k3 does that. Didn't know it was a problem. 

73
Mike R

Find me on "Zello", a walkie talkie or handi talkie type app. I'm listed as KE5GBC. I'm mostly on late at night. 

On Aug 20, 2016, at 12:05 PM, "w3qt@... [Elecraft_K3]" <Elecraft_K3@...> wrote:

 

I'm running a K3s and have a popping noise through the external speaker when turning on the rig and to a lesser extent when turning it off.  I recently changed speakers, thinking maybe a change would help, but the issue is still there.  I'm currently using a TenTec 307B speaker.  I've checked the cabling and terminals and tried a few different shunt capacitors across the speaker termnals.  Does anyone else have a similar issue?  Any ideas what to try next?  Thanks.

73,
Mike, W3QT




Re: [Elecraft_K3] Popping Noise

mikerodgerske5gbc
 

I think my k3 does that. Didn't know it was a problem. 

73
Mike R

Find me on "Zello", a walkie talkie or handi talkie type app. I'm listed as KE5GBC. I'm mostly on late at night. 

On Aug 20, 2016, at 12:05 PM, "w3qt@... [Elecraft_K3]" <Elecraft_K3@...> wrote:

 

I'm running a K3s and have a popping noise through the external speaker when turning on the rig and to a lesser extent when turning it off.  I recently changed speakers, thinking maybe a change would help, but the issue is still there.  I'm currently using a TenTec 307B speaker.  I've checked the cabling and terminals and tried a few different shunt capacitors across the speaker termnals.  Does anyone else have a similar issue?  Any ideas what to try next?  Thanks.

73,
Mike, W3QT


8401 - 8420 of 35512