Hi, One puzzling issue i encountered is that the unit is not able to tune into any MW/LW frequencies! The preselector for 0-1700Hz at slot 7 appears to block out all signals below 1700Hz, as seen on t

Hello, What could be a setting that impacted the Bypass function? I have the widest (6 MHz) bandwidth on, but not the full bw visible. Only RX1 in use. No attenuator, no NB. Playing around with settin

Unless I misunderstood, Elad would begin work to make a dll for use with the HDSDR software. It would be nice if you could indicate when it might be available. -- Bjarne Mjelde arcticdx.blogspot.com R

Hello Group Did any one try the W2EBY amp with the ELAD FDM DUO ? Also what is the class of the final amp stage in FDM DUO. class E or AB ? Any inputs welcome Thanks 73 jith VU2OY

Does anyone know when this amp will start shipping? I would love to buy one to match my FDM-DUO. No response from ELAD email and voicemail. Regards, Bob N5VJV

Hi, There seems to be a bug related to the SW2 ”Presel.Byp.” tickbox, in version 3.55: If you have the box ticked, open the settings dialogue and press Apply within, the bypass is not in use (although

Hi all, version 1.79 of ELAD Remote is available for download on the ELAD website at https://www.eladit.com/it/download?path=sdr/DUO-ART_EladRemote/1.79 The main improvement is the ability to cooperat

All, Would welcome your views. The silver paint on the indentation of my tuning knob has largely worn away. I'm considering repainting it, but before I do, has any one has success doing this and if so

Hi all, Is it possible to view SWR in the FMD-SW2 software? I am operating my FDM-DUO with FDM-SW2 remotely (via Splashtop Enterprise) and I really need to be able to monitor VSWR. I was expecting (ho

Hi, I have been venturing down the rabbit hole of having three of the receivers in the SW2 software be controlled over virtual serial cables by three instances of the WSJT-X software. While the Audio

I have looked but I am unable to find a way to adjust the level meter to compensate for an external LNA. I use one on 6m with a 3dB splitter. One side goes to my TS-890S and the other side goes to the

Hello all, my shiny new S3 arrived, and I have been using it on 6m. I want to use RX1, RX2 and RX3 and CAT VRX with 3 instances of WSJT-X. The problem is that there does not appear to be a com port fo

Sorry I should have changed the title. Hello Vianney, I have asked Elad twice about the PN performance of the TCXO and OCXO of the FDM- S3 without a response. Can you please help with this? Many thank

All, Still getting to grips with the FDM-DUO and have to say that with each Op session I am more an more impressed. Apologies for the potentially dumb question, is there a simple way to configure the

Hello, has anybody on the group succesfully interfaced the 705 to the ART 120 amplifier. Needing to protect the PTT signal from the 705 against feedback/transients from the amp. Assume from what I hav

Is it possible to set up 3 virtual receivers in FDM-SW2 that allow simultaneous monitoring of 3 different frequencies via VAC.? For instance, I might want to monitor 50.313 FT8, 50.318 FT4 and 50.323

Hi all, Most impressed with the FDM-DUO on FT8 and JS8CALL, but now also looking to use with VARAC to drive Winlink express. VaRA doesn't have any settings for the Elad, is there an alternate that wil

All, Grateful for advice. Trying to configure the FDM DUO to work on FT8, all appears well apart from the fact that my PC is not recognising the audio from the radio. The SW2 software works and JS8cal

I've meanwhile found the RX/RTX input schematics as posted by Clint Chron in May 2020 in the "Photos" section. Please disregard my Message/Question. 73, Klaus, DK3QN

Good day, On page 6 of the DUO documentation there are 2 block diagrams of the DUO architecture shown: Picture 1.3.2 presents a general block diagram where the "Power and Filters Bank" is only active