Both ideas have been studied and some prototypes have existed, but no concrete products. Regards, Vianney

#linux #duo-art #wsjt-x

Thanks Giovanni, Yes I am aware of this, I already use Splashtop for this purpose, however I was asking more about the possibility of something like this (SW2 server/cleint, or a IP remote hardware in

#linux #duo-art #wsjt-x

To remote control SW2 you can use TeamViewer, that let you control all the Windows PC running SW2. As previously said, to use ELAD Remote, the hardware and software used to communicate is built into D

#linux #duo-art #wsjt-x

Hi Giovanni / ELAD, Is there any likelihood of an IP remote solution to control the FDM-DUO or FDM-SW2, that doesn't require the ART? Either as a hardware based add-on box, or a software based (FDM-SW

#linux #duo-art #wsjt-x

Just an update. My Duo Art is still in Italy. They are working on a software fix but the developer was ill and the resent troubles have caused additional problems for this small company. I don't need

#duo-art

Hi Ron, at the moment, no. The hardware and software used to communicate is built into DUO ART. Regards, Giovanni HB9EIK IU2PKP

#linux #duo-art #wsjt-x

Can I run the FDM-DUO remote without an ART amplifier attached? Regards, Ron L

#linux #duo-art #wsjt-x

Hi all, version 1.79 of ELAD Remote is available for download on the ELAD website at https://www.eladit.com/it/download?path=sdr/DUO-ART_EladRemote/1.79 The main improvement is the ability to cooperat

#linux #duo-art #wsjt-x

Hi Espen, For Tx Audio, you can try to change audio Tx compression in the Setup screen, trying higher baudrate, or Uncompr. Tx Bw in the same Setup screen is 50-4k ? Any effect using lower Mic gain or

#duo-art

Hi, I have now had time to do some qso's with my remote Elad Duo + Duo-ART 120. The software works quite well, I have 350Mb/s at home and 150Mb/s through two fibre networks, mean ITTR lies around 75ms

#duo-art

Hi Giovanni, thank you very much for your effort in fixing the setup problem with EladRemote v.1.77 today! More than 2hrs in Teamviewer-sessions and now v.1.77 runs well! The CW-keying issue was also

#duo-art

Hello Kjell-Goran, thank you for videos which show the problem clearly, but the cause can not be clear for us without having the DUO-ART to inspect. It may be the power supply which goes into protecti

#duo-art

Good questions, unfortunately, I'm not a Windows expert, so I cannot suggest anything related to this system. If you reinstall 1.76 you can verify if it is a problem not related to 1.76. If 1.76 works

#duo-art

Hi Giovanni, Neil, I understand the volume settings. It was set to 50% when I had started EladRemote v. 1.77. But I did not try 1.76 just before updating, I know it has worked earlier when I was testi

#duo-art

I'd say it's a mixer source set too low. -- De todas partes se vuelve, menos del ridículo.

#duo-art

Hi Espen, hi Neil, correct, the AUX Volume is used because it controls the USB audio, while Main Volume controls the speaker. The Aux volume is controlled by EladRemote "automagically" (normally set a

#duo-art

Hi Neil, tnx for your response. No non-sense at all! Yes the AUX VOL has effect, and is already turned up to 100%, and so is the audio volume of my PC, and still I would need an audio amplifier connec

#duo-art

Hi Espen, I don't have a DUO-ART, so this might be totally irrelevant, but does the setting of AUX VOL on the DUO menu #6 have any effect like it does when using the soundcard output from the DUO? Min

#duo-art

Hi, I have now set up a romote installation of my FDM-Duo+Duo-ART and tested it locally, and it works quite ok, but the Audio is weak, and requires NR, ATT, AGC to be turned OFF to get a good sound. A

#duo-art

Hello Vianney, I have created a folder in the Files section named "DUO ART power-up". I have uploaded two short videos. One video for power up when the rear switch is on 24/7 and another video for pow

#duo-art