No, not a typo. Changed the IP to 192.168.1.136 and it now works Thanks Tony

Hi Giovanni The DUO ART IP is 192.168.2.136 and subnet is 255.255.255.0 and gateway is 192.168.1.1 The IP of this computer I'm typing on is 192.168.1.115 and subnet is also 255.255.255.0 I just tried

Hi Vianney Starting the EladRemote results in the program starting with an on-screen error "Not connected to remote RTX" That is ./EladRemote, IP and then password although I did try both ways I tried

Hi Giovanni. Yes I realise that the DUO should be powered from the ART, I was trying to let you know what errors I got under every possible scenario. The Remote is on but the software still can't conn

Hi Giovanni Yes DUO is powered from DUOART Cycling the DUO power with the ART powered, the 2 warnings remain, plus I get a "DUO extio warning" which can be cancelled on powering the DUO. Cycling the A

Hi Giovanni I spent a while this afternoon swapping cables and 3 different hubs but still have errors. Every time I start the Duo/Art I get "remote warn USB" and "audio read warning", plus the "remote

Hi Giovanni YES .. that cured it, now on 115200 But the Remote warning has now been replaced by "Audio read warning" and it's still not connecting to the remote computer. But that's progress. I don't

Hi Giovanni The error reset button works or to be precise it removes the error message, but it is still on "local". The sequence is, switch to "remote", DUO flashes to TX, display changes from "remote

Hi Giovanni I have the DUO and the ART connected as in the remote setup in Annex B of the manual. I have the CAT from the DUO direct to the ART USB port and the TX & RX connected via a hub to the seco

Hi Giovanni I thought there was an error regarding folders, but as I know very little about Linux I didn't know if I was correct. But success! I now have the console on my screen. Unfortunately it is

Hi Giovanni I have (temporarily) given up on Windows. Today I installed Linux Mint on a spare laptop and started to install the remote S/W All went OK until I got to .. sudo make clean all install ..

Hi Giovanni Thanks for the reply. That was the problem as Windows of course saves downloads to usr/tony/downloads. Using that route appeared to work, but it seemed to stop suddenly with the report "C:

Hi, I tried to install the Remote software last week and failed, so I postponed trying again until I had more time, which is today. But failed again exactly the same as last week. I'm trying to instal

Aaron, I must ask the question, why would a British amateur call be registered on the US FCC database? FYI G4 +3 UK calls were issued between 1971 and 1985 and as they are issued in sequence, G4DBN wo

Funnily enough I had the opposite problem. Ran the IE version and it stated it failed, tried again and it said "Band plan already updated" and sure enough it had! Work that one out ;-) Tony, EI8JK

Hi John Did you install the UK band plan or is the Duo as you bought it? Country band plans are here ... http://elad.it/download/sdr/FDM-DUO/Bandplanes/index.php?lang=EN 73, Tony, EI8JK

I am doing a three part YouTube series I call SDR School. If you feel a little left behind with all this SDR stuff, this might be for you. I have tried to bridge the gap from the traditional superhet

Yes .. I'm also (not so) patiently waiting as well. I'm sure it will be worth the wait though. Tony, EI8JK

Hello group I have a Duo-Art + Duo that was working perfectly. I updated the Art firmware a couple of weeks ago and that all worked flawlessly. However I haven't used the combo for about a week and wh

Hi Andy I have a similar problem that is also undocumented (that I've seen) I have a Duo Art 120 watt amplifier which should have the RX and TX sockets connected from the Duo to the Art. You then have