Hi Peter, Thank you for the info. I have a headphone jack on the computer but audio is still coming out of the speaker when connected. I am still studying the manual and on line videos. I am sure ther

Paul; Hint on setting MENU items. Press Menu button (F5) Rotate Knob E2 to correct menu item number. Press Knob E2 Rotate Knob E2 to desired function. After desired function selected PRESS Knob E2 aga

Peter, thank you. That fixed the issue. I tried it several times but it "did not take". I am learning!! Is there any way to listen to computer audio with headphones? I guess there is a setting but min

Hello Paul. Check Menu Item 40. It should reverse the dot and dash function. Of course it this easy part doesn’t work, you can always reverse the wires on the paddle or in the connector plug. 😊 Just a

Hello: I just got a great little DUO today. I cannot figure out how to reverse the setting for the paddles - dits are on right and dahs on the left. I have tried the menu setting in the rig but nothin

Hi i have now tried it on S1 and I also got confused by this since i had an frequency error 13khz and ppm didnt work, finally i found this blog Its been 3 years now, any idea if it can get fixed, I ha

Hey All USA & Canada Customers, I’m still have phone coverage issues, if you need sales or support you can try the old/current number 312.320.8160, if you don’t get An answer and it goes to voicemail,

Yes I expect that you are right Koos. This is why it is better to use max gain, no agc and the demodulated audio and an audio power meter like Rob Sherwood and the ARRL do when quoting MDS. Otherwise

Probably the noise floor refers to the displayed noise floor on screen. That is determined by the width of the bins of the FFT, << 500 Hz. But, indeed, this is not documented very well... Koos PA0KDF

In a 500Hz BW a perfect receiver has ~ -174dBm/Hz + 26.9dB = ~ -147dBm, therefore -152dBm in 500Hz is impossible. I think that this must be a mistake. Regards Conrad PA5Y From: EladSDR@groups.io <Elad

Thanks for the MDS info Vianney. Regards Conrad From: EladSDR@groups.io <EladSDR@groups.io> On Behalf Of Vianney Colombat via groups.io Sent: 17 January 2023 17:13 To: EladSDR@groups.io Subject: Re: [

Vianney, Is there anyway that the software can be modified to be able to turn on the PERAMP for VLF, LW, MW and HF? Everett N4CY In a message dated 1/17/2023 10:13:09 AM Central Standard Time, vianney

Mmm, not impressive. What are the image rejection numbers and spurious responses? Koos PA0KDF

I have these data available now (@192kHz, 500Hz BW): Noise floor @144MHz : ~ -137dBm, ~ -152dBm with preamp MDS @144MHz : ~ -127dBm, ~ -142dBm with preamp Clip @144MHz : ~ -9dBm, ~ -30dBm with preamp

Vianney do you intend to publish performance parameters for the down converter? It is not cheap and while I trust Elad I am not going to buy something without any specifications. I have asked several

Hello, the current state is still the same as described in the messages below. Regards, Vianney Il 24/12/2022 14:00, R GRAYSTOCK via groups.io ha scritto:

Hello, we do not have this answer actually. Due to the difficulty to retrieve electronic components at a decent price, for now we produce the downconverter in batches of 10-15 pieces. Regards, Vianney

I can't see the bin size on the main display, but if it's 23Hz for instance, the s/n in the IF at 0.4 Hz bins would be around 17 dB lower for a very clean carrier. Compare the bin sizes then calculate

#eladsw2

Tony, That is excellent.....Okay I have mine setup like yours and was able to see the signal at -140dBm, but only on the IF screen. I could not get it to show up on the mail waterfall. Also it did not

#eladsw2

Try this link: Screenshot 2023-01-15 102116.png Tony From: EladSDR@groups.io <EladSDR@groups.io> on behalf of Tony_AD0VC <canthony15@...> Sent: Sunday, January 15, 2023 11:53 AM To: EladSDR@groups

#eladsw2