Got a screen shot? Mine doesn’t show anything like that??? Bill

Great! Now I wait for a raspberry release 😙😙 -- _____________________ Michele IZ5035SWLmartedì, 22 marzo 2016, 10:59AM +01:00 da "gfranza@... [elad_sdr_en]" <elad_sdr_en@...>:

Hi all, in the ELAD website, at http://www.eladit.com/download/sdr/Linux/index.php?lang=EN you can find the new sources for the integration of ELAD S1,S2,DUO devices into gnuradio. The news are: 1)

Hi Neil, Basically have it working here also, didn't realise it could label the spots on the SW2 Spectrum . I am still a bit out on frequency reported and actual tuned . Still learning, Cliff VK2NP

Go to "Set" Go to "Tuning" tab Make sure the VHF band is checked off... It defaults as unchecked... The same applies for FM broadcast This applies to the latest release of SW2 software Regards, Rafman

Hi Chris, mine has to be set to 46 to be exactly on frequency as compared with a Marconi 2440 locked to a 10MHz GPSDO. Normally, I run with the GPSDO into the DUO, but after seeing your post, I

I have left the DUO and a Thurlby Thandar TF810 frequency meter running in RX for 1 hour and found the DUO was not centered on the displayed frequency. Under 13.8V , at 14.200 MHz, when setting the

Can I ask a question? Are you controlling another device at the same time you are the FDM-S2? Perhaps you are using Omni-rig to have them work in parallel? If so...and the other device does not

OK, sorted it now, I'm running on RX1, using 48kHz IF out of VRX1 into a VAC and using CAT in FT-897 mode into a virtual serial port. I am connecting to 127.0.0.1:7300 which is enabled on Skimmer,

Hi Jimi, most data users will be using USB audio into the DUO, and that automatically turns off compression, so support of digital modes is built in to the design. If anyone is still using an audio

Hi, A few days ago I was reading à conversation on the digitalradio reflector about what mode should be used when working digimodes. Some of them said USB while the others said DIGI. My other Rig

Steve, I've tried again during lunch break today and there is a weird issue with the CAT frequency, the spots are reported with frequencies in baseband, and are mirrored about 0.0, which is not

Are you using the latest version of FDM-SW2? I think early versions used to have a check box option at the top of the Advanced Tab. You can check what version you are running from the About Tab. The

It's for the SDM-S2 Bill. No can't get it to work. 73, good DX Gust ON6KE

DUO or FDM-S2? I think with DUO there is a sequence that needs to be entered to go beyond 60MHz (search the Yahoo Group forum). For FDM-S2 I believe it should just work. Bill

Hi Bill, none of that works: - direct entry of the frequency, no - pulling the tuning MHz bar, once you pass 60 MHz it resets to 60MHz, so no - have the 2m band button selected in Tuning, Preset

Just keep tuning until you get there? Do you know about the 3 tuning bars near the bottom? They allow for large jumps in frequency. You can also double click on the frequency at the top and directly

Hi everyone, we all know that the Elad user manuals leave much to be desired. Can anyone in a few words explain how I can get the FDM-S2 to listen on 144 MHz? Thank you. 73, good DX Gust ON6KE -

Yes, my fault... The box is the power injector 😁 Thanks to all the replyers -- _____________________ Michele IZ5035SWLlunedì, 21 marzo 2016, 11:41AM +01:00 da "roger duym rogerduym@...

No problem one pipe is fine till you expand your requirements You get more when its registered or try this one :-) http://vb-audio.pagesperso-orange.fr/Voicemeeter/ Regards Frank G3YQA