Neil, Got it set to KEY.. Dave KK7SS

Hi Dave, have you got Menu 37 set to PAD instead of KEY perhaps? Neil G4DBN On 26/11/2020 00:12, David KK7SS wrote:

Anyone help? I can't seem to get the FDM-DUO recognize my (new to me) bug! All I get is 'dits'! It's not the bug because I have it working with my CTX-10 and X5105. Or is it not compatible? Dave KK7SS

UPS dropped off my S3 OCXO this afternoon and it went in seamlessly. Disconnected the S2 and put the S3 in its place. Nary a glitch. Just for fun, and wondering if I would overwhelm my computer's

Ok Omnirig works back, I found the solution the correct name in the window in Omnirig was not with Kenwood but with Elad. Both ports must be under correct name. Like Kenwood and Elad in my case, there

Clint, are you receiving with the RTX/TX antenna ? Vianney Il 09/11/2020 13:30, Clint Chron ha scritto: Le informazioni contenute in questo messaggio di posta

I answer for completeness. The issue was related to the sample rate, SW2 accepts only files with 48kHz sample rate. Vianney Il 21/11/2020 19:52, Christoph K. Schweiger

Maybe this FAQ can help you : http://support.eladit.com/kb/faq.php?id=81 <http://support.eladit.com/kb/faq.php?id=81> Vianney Le informazioni contenute in questo messaggio di posta elettronica sono

What does the Omnirig Control window show ? Il 25/11/2020 14:44, fb311569@... ha scritto: Le informazioni contenute in questo messaggio di posta elettronica sono

Yes I do but nothing, when the software S2 stay out I check with N1MM and Omnirig works fine. So it's in the S2 software Thanks for you answer 73, Maurits

Hi Vlanney, that really helped, thank you very much! I did reset the number settings and it worked. No idea what SW did change it, I never did play with that. However, it would be good if a

Did you check the checkbox here > Menu > Remote Ctrl > [ X ] Enable Omnirig Control ? Raimund .

Are there a way for a reset in the software ? .Or in the map where the software stay .Reasons I have not any connection anymore with Omnirig Help are welcome Thanks in advance 73, Maurits ON3MK

Eckhard, I think the issue is due to "Decimal symbol" and "Digit grouping symbol" settings which are equal, see picture below. Please try to enter different values for these two

Eckhard, do you have close the software before to delete the file "FDMDS1Config.xml" under "Documents\ELAD\FDM-SW2" ? Regards, Vianney Il 20/11/2020 17:59, Eckhard

I have a Kenwood 590 SG ,and its works good with N1MM log program .A week ago I install. The Elad software for the S2 receiver .I using also Omnirig ,so its one of the two that run with the Kenwood

Als Ham gebruik ik N1MM, met mijn grote Kenwood TX. Nu heb ik de S2 what are the settings for using N1MM and S2 With Omnirig can I run just one px. VSPE don't help me. Help are welcome 73, de ON3MK

Hello Maurits, do you see the S2 in the device manager ? Vianney Il 18/11/2020 11:22, fb311569@... ha scritto: Le informazioni contenute in

VisualGPS, LLC

I sometimes use the online tool at https://www.corefiling.com/opensource/xmldiff/ which seems to be schema-aware. Altova XMLSpy is a tool I use at work, but it is expensive! Their