Heinz-Juergen Aha!,, I'll give it a try this morning danke sehr Dave G. KK7SS

You won't brake it. Mine is set to "0" and still working. "0" was set as Default, i did not changed it. With this setting i could match my HyEndFed 5 Band Antenne to all Bands from 160m up to

Alan, I've thought about try setting it to '0' but I'm sorta nervous about that,, Only just got the ATR-60 and don't want to break it... :-) I've got a shorty 80M trap dipole thats ok at

Dave, Ah! I'll have to guess. Maybe it does it's best. Does "(0=Off)" mean no report of "Too High"? Try it. 73 Alan G4ZFQ

Alan, G4ZFQ I know exactlybwhat the "very fine manual" says.. BUT the question I ask is "What is the behaviour of the ATU when the target is set to 0" ? Dave G. KK7SS (ex-G3UTY, ex-ZS6MG))

The Very Fine manual says Menu 22 "Target SWR (0=Off)" 73 Alan G4ZFQ

Greetings, I am using an Elad S2 on a Win 8.1 quad core 16 GB computer. I am using the native Elad software and also SDR Console (SDRC) (not at the same time, of course). Also I am using the 3.072

Espen, Yep.. F4. (MODE button) does the job Thank you.. Must be a misprint in the User Manual Takk :- Dave KK7SS

Hi Espen.. I did try setting SWR to 1.5 on a frequency that I knew was 2:0.. and I got the "Too High" like you said. It's that "set to 0" that's peaked my interest :-) 73 de Dave

Hi Dave, Cannot say what happen when set to 0, but it is not logical value. But you could1.5 try and tell us what happened ;-) But when set to 1.5 it tunes until 1.5 or better is accomplished, or when

EDIT: First line should read "Menu item 22" Dave G. KK7SS

What occurs if Menu item is set to 0 ? Does the ATU try to find the best match and stop? What happens if it's set to 1.5 and the ATU can't get a better match than 3:1? I'm not understanding this

Sorry to hear your problem, I would check the following: The ART must have the tuner installed, of course, and set enabled via the front buttons on the ART. Next It is really written in the manual

I've followed the instructions in the FDM-DUO and ART-60 user manuals to the letter. But a long press on F3 on the FDM-DUO does NOT initiate a TUNE on my ART-60. I can initiate a tune from the

Perhaps there's a capacitor inside keeping the voltage up on some processor, just sufficient to maintain memory contents in very-low-power mode and it needs [several hours] to leak away. Pure

Thanks for the info Kjell, and to Andy for his response too. Well… after leaving the thing for a day unpowered, I now find it’s working again! It’s a bit of a mystery because, as I described

Mine does the same when running from an external 10MHz reference and this is momentarily interrupted. It doesn't recover and goes to full-scale noise even if 10MHz input is restored. I just reset

Hello Mark, My DUO behaves like yours sometimes when the PC is booted (I always power-up the DUO first before the PC). It has done so for about a month. The S meter is at S9+40 all the time until

I just wonder if anyone has seen this failure before, and anything I can try to fix it, before I send my FDM-DUO back to Elad: My FDM-DUO was connected to, and powered by, my DUO-ART 60, when the

If you break out the mic socket PTT on the back of the DUO and use that for a footswitch or external mic switch, doesn't it transmit OK using the advanced TX? Easy to test by