Re: Duo with pc headset ssb #eladduo

Harke Smits

Hello Paul,

I would start with reading the note by Andy first. You can find it here:

Indeed, I use the DUO with a DB6NT transverter (3cm), or my own (13cm), but the switching principle is exactly the same. So you need to place a resistor (4k7) from +TX (at 2m) to output. I use a 3 resonator hi-Q band pass filter at 144 MHz with a notch at 122 MHz.Align with vna. At the input a low pass filter. Also the TX section uses a low pass filter. In fact rather simple. Let me know by pm if you need more info. The sequencer is in the transverter.
Best 73 de

Harke, PA0HRK

On Sunday, October 18, 2020, 04:33:45 PM GMT+2, Paul Andrews <pandrews@...> wrote:


Thanks for the good news.  I want to use the Duo as an IF radio for a Khune transverter.

Do you also use a filter on the TX output?

Should I use a bandpass filter centered at 144 MHz or a 122 MHz bandstop (notch) or both?

I enjoyed your webpage on SpectraVue.

73 - Paul - W2HRO

On Sun, Oct 18, 2020, 06:41 Harke Smits via <> wrote:

Allow me to throw some experience in. A couple of years ago I was looking for a decent 2m sdr and I was unimpressed by the market. Either not good enough or too expensive. My application is base station for microwave EME. Then I was informed of the article by G4JNT about using the FDM-DUO at 2 m and I immediately bought a DUO (second hand). It uses the DUO RX in undersampling mode, it's clock is at about 122 MHz. The TX is used normally as the sample frequency is higher than 144 MHz at about 225 MHz. All you need are some filters and amplifiers. It works like a charm and I could even recommend using the DUO as your 2m home base station in all but the most demanding operating conditions. I used a vna to align the filters; with a notch at about 122 MHz. I do not need a low noise figure at 2m obviously, but that is not a problem at all actually with a PGA103 in the front end. With a good signal generator I calibrated the DUO's S-meter by inserting a small attenuator at the RX side in front of the DUO. I found the compression level at 2m to be quite high but unfortunately I can not do NPR measurements at 144 MHz due to lack of a good notch filter.  I have used it at 13 and 3 cm EME without any limitation. I hear beacons, sun- and moon-noise and of course: many stations. For me this has made EME (with my relative small station) really great fun.
I have never operated the DUO in any other operating condition, but at 2 m it's great.
The filters and amplifiers are housed in a small case under the DUO which also contains a Wenzel 10 MHz OCXO to stabilize the DUO.
Just a happy user and no connection to ELAD in any form......
Best 73 de

Harke, PA0HRK

On Sunday, October 18, 2020, 03:31:40 AM GMT+2, Paul Andrews <pandrews@...> wrote:

Are you using this 144 Mhz filter / amp design with your Duo?

The Duo as a 28 MHz IF radio is excellent.  I use it on 432 and 1296 MHz.

No I better understand the limitations at 144 MHz undersampling.

If the Duo is run at 144 MHz with a transverter, is the filtering still required?

73 - Paul - W2HRO

On Sat, Oct 17, 2020, 18:34 Neil Smith G4DBN <neil@...> wrote:
Hi Paul I use a G4DDK Anglian transverter to get the DUO on to 144, but
it is quite simple to get around the mathematical and technological
issues with the DUO at 144 MHz.  Running 144 MHz on a 122.88 MHz sampled
A/D converter means you lose a lot of sensitivity simply because of the
way sampling works. The noise figure of the DUO at 144 MHz is extremely
poor as a result.  Also there is aliasing, so you get noise from the
image frequency as well, and Band 2 FM broadcast breakthrough from
around 100 MHz.

Andy G4JNT has designed a filter and amplifier board to improve the DUO
performance on 144. Have a look at
<> where all is explained...

Neil G4DBN

On 17/10/2020 23:19, Paul Andrews wrote:
> Neil,
> Do you use a 144 MHz IF with your 10 GHz system.   I tried using my
> FDM-DUO configured for 144 MHz with a Khune transverter.  I was not
> successful looking for the beacon.
> 73 - Paul - W2HRO

Join to automatically receive all group messages.