Let's see if we can fix this one bit at a time.
First step, let's find out if CAT is working at all.
Using the same COM port that works as a TS-480 in HRD, and
with no other programs running that might be locking the COM
port, confirm that the WSJT-X or JS8Call settings are the same
as worked in HRD. Should be 38400, 8 N 1 as usual.
Now I'm going to assume that you are using the latest JS8Call
or the latest WSJT-X (so you have the current Hamlib setup,
which is built-in to those).
Check that you have the radio type set in the program
settings to Elad FDM-DUO in the drop-down box (don't use
TS480, the Hamlibn for that is buggy, the DUO library
functions are new and work perfectly)
Check that you are set to PTT using RTS on the same COM port
which worked OK with HRD for CAT. The rest of the settings
shouldn't matter at this point, but set them anyway to Fake It
split and USB mode so you don't have to go back and fiddle
with the settings later.
Assuming that is OK, and the settings are all correct, click
the "Test CAT" button.
If that doesn't go green within a second or so, we need to
dig further into whether something is stopping the COM port
from working, so stop at this point and report your findings.
If it does go green, then click the Test PTT and see if the
rig goes to TX. If it doesn't, then check the DUO menu 54 and
the PTT is set to IN+RTS, then retry.
If that still doesn't work, you have a different issue around
the RTS line, so change the PTT setting to CAT and try again.
So, now you either have CAT and PTT working, or just CAT or
Can you test and report on whether those settings work in
JS8Call and/or WSJT-X?
Next step is to get receive and transmit audio working, but
let's go one step at once.
On 31/08/2019 12:24, Bill / N1ASS
Thank you for the reply,I had some time to
try to make it work but it still doesn't not.I did
everything as you showed in the screen shots.I know all
usb ports are working,Hrd and logbook works as ts-480 and
cw idier works as ft-897.What you think I should try next?
Bill / N1ASS.73.....
On 8/29/2019 3:07 PM, Neil Smith
Good advice from Charlie. Get FT8 working with WSJT-X
first as there are more users out there to ask for help.
I had never tried JS8Call, so I checked my setup with
WSJT-X first, then downloaded and installed JS8Call with
Set up looks like this:
I have TXIN on the DUO menus set to AUTO and PTT set to
When I hit Test CAT, it worked and went green (my default
COM port is COM3, discovered the way Charlie suggested).
Then I hit Test PTT, the rig went on to transmit and the
button went red.
For the audio streams, I normally use Virtual Audio Cable
wiht SW2 on receive, but for this test, I picked the
FDM-DUO audio device on TX and on RX
I set the DUO menus for AGC OFF, AGC GAIN 1 and AUX VOL
about 6 to get the level in JS8Call somewhere in the
30-40dB region on band noise. I also messed with the gain
on the Windows audio device for the DUO to drop the gain a
Seems to work fine.
Much simpler for me to use SW2 and Virtual Audio cable as
I have multiple receive programs listening at the same
time to the virtual device and don't want to playh with
JS8Call, but it looks like it is just the same to
configure with the DUO as WSJT-X
On 29/08/2019 17:33, Charles
Bill, IMHO start trying a more common digital mode.
The nuances of setting and using JS8call are best handled
after getting some experience.
I suggest try WSJT-X and look at FT8.
As for com post selection, I am not certain the root of
I have one suggestion that solved the problem for other
You did not specify your operating system, but I will
assume it is Windows.
Make sure your DUO is powered off, and get the System
display under Control Panel opened.
Take careful note of the USB ports listed.
Now power on the DUO and you should hear three audio
"pings" as the DUO drivers get loaded. You will see ELAD
samplers, the ELAD audio card, and a com port appear with
Note that comport number.
That is the com port to your DUO.
73 de NN3V