Something about a TCP and network server error, but I'm connected to my 7610 via the virtual com port ?!?!?!

Hello Does DXLab WinWabler interfaces / Supports the HAL DXP-38 RTTY modem, or will i have to switch to software TTY type such as MMTTY? Thanks Saad N5FF

DXV = 4.7.9 Whenever DxLabLauncher starts everything, DXView will not start out minimized. When I eventually terminate all of it, everything except Commander was minimized. -- 73 Bob KD7YZ AMSAT LM #9

worked k3y/kh6 when logging it to dxkeeper it would not take it when i changed to kh6/k3y it would log it. is this correct? I would like to be able to log k3y/kh6 and still be HI. Murf n7uvh

I want to generate a report that only shows my DXCC progress on 160M, specifically countries I have worked but not confirmed. I've spent a half hour plowing through the help and the wiki, but have not

Have been through the help with no success on this. I want to have DXKeeper display my log, sorted in UTC and Date order all the time so that I can see the last contacts logged. When I mouse on a spot

When I upload to LoTW the "Upload to LoTW" tab and menu shows the upload was successful. However, when I try to "sync LoTW QSO's", it only shows a date from a couple of weeks ago. This occurs even few

Hello all, Not sure if this question is for DXLab, Microham or both I have multiple radios interfaced to DXLab. Each radio is paired with a Microham MicroKeyer interface. DXLab communicates fine with

Hi, After installing WSJT-X 2.1 I have intermittent problems during FT8 and FT4 QSOs with the connection to Commander (which I use for WSJT-X rig control) I now and then get the error WSTJ-X error mes

There are numerous times where DX Lab posts a warning or question in a small box that is typically located in the dead center of the monitor. Call book look up errors. Notices about overwriting entrie

Another oddity I keep having, is that When I press "New" for entering a just completed QSO,and BEFORE I enter a callsign, the propagation-mode line is Blank. I previously did the cntrl-dbl-click to se

i do not want to display or hear any audible alarms for FT4/FT8 spots. i have unchecked the boxes for the mode on SC's MODE filters, which seems to fix displaying those modes, but that does NOT seem t

Dave, I turned on SC this evening and the filters were again empty. When I shut it down, the message appeared that warned me that the filters were empty and wanted to know if I wanted to save it that

I have a filter that sorts for QSO in 2021. Filter looks like this. DateDiff ("n", QSO_BEGIN,QSO_END)>0 and QSO_Begin > #2021-01-01 00:00# It only works if the log page display is in ascending order.

I have not been able to figure out how to do this - instead, I go to log a QSO and am admonished that my end time entry is invalid. Moreover, unless I'm careful, I enter it in the wrong format, and am

hi i am running the latest version of dxview which is controlling the rotator works 100% however when i click request rotator position ever second the heading display seems not to respond so pushing t

Ron, I received an email message from you whose return address is garbled, preventing me from responding to it. I responded to your yahoo.com email address. 73, Dave, AA6YQ -- This email has been chec

Ron, I received an email message from you whose return address is garbled, preventing me from responding to it. I responded to your yahoo.com email address. 73, Dave, AA6YQ

Good evening all. I have a situation with Workspaces and using multiple rigs....here's my scenario: I have several radios utilizing Workspaces: ICOM 7610, ICOM 9700, and Anan 7000DLE. I have setup a D

Dave, I rebooted for a windows update, and when I start everything back up my spotcollector SQL filters have vanished. Any idea how I might recover them, or do I need to re-create them? Thanks & 73 de