When I use WinWarbler to send a prerecorded phone .wav file it sounds distorted when listening on a separate receiver. I can understand the audio but it sounds terrible, like it is over driving, so I

I was looking for a way to change the Band Modes to separate FT-8, etc. in SpotCollector. In doing a search of the SpotCollector File I found "BandModes 2022-01-06" It works very well separating all B

is there a way to using spot collector to right click on a callsign and read the radio and enter it into the capture field or log it, if i double click on a call it puts the frequency received thru sp

Hi everyone! I've been experiencing a problem when using WSJT-X or JTDX and DX Commander. I've been searching around, and have found that this is not an unheard of issue, but haven't see a particular

Mike, the original error report was posted on the WSJTX group by Benjy AC4XO, not by me: https://wsjtx.groups.io/g/main/message/39589 Benjy and Steve, I suggest that you take Mike's suggestion below.

I can run WSJT-X with Commander 15.15.1 doing CAT control on my K2 in WSJT-X split mode "None". In split::rig and split::fakeit, TX is blipped for less than 1 second rather than the normal 13 or so se

After syncing, there is a report that is displayed about changes, new confirmations and such. Are those reports saved somewhere or when they are deleted they go to the great bit bin in the sky?

Hi, I imported a large number (over 15K) of QSOs into DXKeeper and I now find that the box for “rx frequency” is blank, while the “tx frequency” does show the correct frequency. Is there any easy way

And then another question that is also about DXCC for Satellites. Can someone tell me how to make a filter so I can see which Qso's new DXCC are for me and what I should get another qsl of? This is no

HI All…I just completed confirming WAS 20M FT8 and I was using the built in WAS award reporting to tell me what was worked and what was confirmed. I wish to do the same thing for all the 10 Canadian p

Good morning, I'm busy making QSO's via Amateur Satellite. But how can I now only filter the Satellite qso's that are valid for DXCC? Because there is a difference between my LOTW score and the score

It stopped again, Dave. I deleted the spots.mdb file, again. Sending errorlog.txt directly to you. 73 from the desert, Fred/NA2U

I don't know where the configuration is for this. I have looked through DX Commander, but could not find exactly what I was looking for. The issue I am having is that after I work a split QSO on CW, w

Not sure if its my configuration, or if its designed this way, but...….. I see a spot for J28MD on 80m...….its over 30 minutes old, so has scrolled off the screen...…..I now work J28MD, and spot him..

I seldom use SpotCollector. I last used it in late July. I opened it yesterday and immediately Recomputed the database because I saw a number of messages after making changes that stated that the data

(DXK 16.8.6, W11 22h2) Somewhere back in time, DXKeeper began recording the following error: 2022-11-03 15:09:19.723 > DXLogMain.Form_load: unable to register MouseWheelControl.ocx: RegisterMouseWheel

I recently worked the P29RO on 17 mtrs the last of October. In running the Marathon Progress Report, the QSO does not show up on the report. It also doesn't show on the Marathon RAT report but does on

Having seen a thread regarding using XML data for QRZ lookup I checked the DXK config>Callbook tab and found that I wasn’t using the XML Data. So I checked the XML selection. I do have a subscription

The errorlog that you sent me shows that Windows will not allow Commander to install the MSWINSCK.OCX component: 2022-11-01 21:58:29.716 > program error 339 in module TCPServer.InitializeCATCPT: Compo

Dave: I tried reinstalling Commander. No joy. Error log attached. Any assistance is greatly appreciated 73 Gregg W6IZT_._,_._,_