Should it matter whether the radio is powered on before or after Commander is launched? I have a Lab599 TX-500 that uses a subset of the TS-2000 command set which sometimes will not connect (using 960

Hello, I configured SpotCollector (9.4.0) for two spot sources: db0soe.de (dxspider v1.55) via telnet and CQDX via IRC (us.worldirc.org). CQDX obviously shows truncated callsigns with a maximum length

I have been running an Icom IC-746Pro which went belly-up earlier today. So I ordered a Yaesu FT-710AESS from HRO a couple of hours ago. I have been a DXLab Suite user for almost 20 years with over 6K

I am a member of a makerspace with a Ham shack. The computer connected to the radio has a login for each ham who has been trained on the procedures of the shack. Very few of these users have administr

I ran into a TO1Q call that DXLab doesn't accept. It is a special event station operating out of Guadeloupe. How do I log this? 73 Jeff kb2m

It costs nothing for anyone -- ARRL Member or not -- to submit QSOs to LoTW, and monitor their confirmation via LoTW. Some DXers are perfectly content with tracking their progress in this manner. It c

If you are using Window Defender Antivirus (Windows 10), update it to its latest malware definition in <https://www.microsoft.com/en-us/wdsi/definitions> before installing or upgrading to DXLab Launch

I have a new FTDX10 that after some fiddling with parameters, has been running on DxLab. However, since installing DxLab, the Yaesu screen periodically freezes and requires a hard reboot to bring it b

I just switch internet providers and having an issue with the new router. When I first set my phone and dxlab computer on the same network it works fine but only for a short time, then I have to reboo

Hello, DXLabs controls my Yaesu FT-950. My Signalink-USB went belly-up and so, as a replacement, I bought a comparatively new product "Digirig". My problem is that, for my FT-950, Digirig uses RS-232

There is a V2 on 160m FT8 that is not showing as needed. I have V2 confirmed on 160m SSB but not on 160m digital. I want to make sure I see spots for all needed slots. I have unchecked all DXCC award

This error problem is no fault of DXLabs! But this problem does affect DXLabs. For over a year while running WSJT, DXView, DXKeeper, and DXCommander, I will get the message in WSJT "Error in Sound Inp

Whenever I start DXKeeper, the config window also starts. I though it might be possible to close it and save the workspace, but one cannot save the workspace while the program is running. I close the

Good Afternoon: I can get Winwarbler to run under Commander, and generate perfect CW with My winKeyer hooked up. I CANNOT get Winwarbler to Generate a PTT signal however in RTTY. I get the correct out

While checking some things Dave asked me to check, I more closely looked at the Defaults tab on the Config window. In the Default Callsigns frame on the defaults tab of the Config window, I had 'Show

Good morning, SpotColloector was working just fine, when i shut down my station last night. This morning, Autoscroll is lined out, in the upper right corner last record button does not function. No sp

Hi all, Just out of curiosity (and impatience and devilment!) I just tried to upload to LoTW again, and this time, it was accepted for processing. How long it will now take to show up is anyone's gues

Hi all, After a short session on the radio this morning, when I attempt to upload to LoTW, I get the following response: TQSL Version 2.6.5 [v2.6.5] Signing using Callsign GU0SUP, DXCC Entity GUERNSEY

Seen some comments today re: some issues with LOTW....Dave or anyone...for about 24 hours now, when trying to upload Q's from DXKeeper, I am getting the following message...Upload to LOTW..."TQSL is s

Thank you, Dave.