I have been running an Icom IC-746Pro which went belly-up earlier today. So I ordered a Yaesu FT-710AESS from HRO a couple of hours ago. I have been a DXLab Suite user for almost 20 years with over 6K

Hi all, After a short session on the radio this morning, when I attempt to upload to LoTW, I get the following response: TQSL Version 2.6.5 [v2.6.5] Signing using Callsign GU0SUP, DXCC Entity GUERNSEY

I have a new FTDX10 that after some fiddling with parameters, has been running on DxLab. However, since installing DxLab, the Yaesu screen periodically freezes and requires a hard reboot to bring it b

Seen some comments today re: some issues with LOTW....Dave or anyone...for about 24 hours now, when trying to upload Q's from DXKeeper, I am getting the following message...Upload to LOTW..."TQSL is s

Thank you, Dave.

I'm being told that ARRL no longer allows "hybrid" applications (cards + LOTW) ... is that right? Is that new? I have a few cards that need to be added but I'm not about to do a separate application f

+ AA6YQ comments below Recently I started getting "Broken: ARRL Section ONN is inconsistent with DXCC Entity VE and State ON" and similar for contest QSOs made with new ARRL sections. + In DXKeeper 17

I thought for sure I remembered that one can do this but I can't find the option anywhere and struck out on the documentation too. Sorry for the n00b question, but can someone please point me in the r

Hi all, Just out of curiosity (and impatience and devilment!) I just tried to upload to LoTW again, and this time, it was accepted for processing. How long it will now take to show up is anyone's gues

When I hover over buttons on Spot Collector, one get's the typical pop up message line EXCEPT when hovering over buttons on the line of Need, Call, DXCC, etc. Have I set something wrong? One get's an

If you are using Window Defender Antivirus (Windows 10), update it to its latest malware definition in <https://www.microsoft.com/en-us/wdsi/definitions> before installing or upgrading to DXLab Launch

I used to but no longer get Spot Collector Spots displayed on SmartSDR Windows. The Settings Spots menu is correct according to your references. The Commander Bandspread selections are correct. I've h

I've been trying to find where the 'database' is for "mode by frequency" to see if i can tighten up the fsk "territories' I've scoured the commander /dxkeeper ..lookiunf doe the databases .etc but can

Recently I started getting "Broken: ARRL Section ONN is inconsistent with DXCC Entity VE and State ON" and similar for contest QSOs made with new ARRL sections. I know there must be a database update

Upgraded to Launcher version 2.2.2 yesterday. I have since reverted to 2.1.7. I don't know if it's related or not, but this morning Spot Collector seems to have lost all the settings. Sources didn't a

Juergen, I have sent you and Bruce K5WBM a version of the Launcher that corrects the defect that prevents execution of .bat files. Note that the Launcher cannot terminate applications started from wit

Whenever I start DXKeeper, the config window also starts. I though it might be possible to close it and save the workspace, but one cannot save the workspace while the program is running. I close the

Hi, I have looked at the manual and I am looking in the wrong place for this information. Along the log page with the contact record there are buttons "need" "date" "since" etc along the very bottom e

I have been trying to track down a periodic "sizzling" sound from my Flex 6600. I'm running the latest Flex SmartSDR on Windows 11 with a new PC 12th gen i9 processor and 32GB RAM. With everything run

I have two Kenwood radios connected to my DXLab Application. I am running windows 7 dedicated to this application and has worked for years. Now at start up I get error message: Invalid Port Number (80