Question
|
nk4l
Good morning, just upgrade Commander to 15.4.4 and all my User defined controls are gone so I re-due them but every time I shot down and turn it back on what I did disappears again?, any thought and how to save it. Thanks. Jose NK4L -- jose gonzalez
|
|
|
|
Joe Subich, W4TV
Are you loading a workspace at startup? If so, update that workspace
toggle quoted messageShow quoted text
before closing but *after* you have recreated all of your user defined controls. 73, ... Joe, W4TV
On 2022-07-05 11:39 AM, nk4l wrote:
Good morning, just upgrade Commander to 15.4.4 and all my User defined controls are gone so I re-due them but every time I shot down and turn it back on what I did disappears again?, any thought and how to save it.
|
|
|
|
nk4l
hello Joe no it was not happening before now I set up up all my preferences and when I close and re-open the define controls are gone but the sliders are ok.
On Tuesday, July 5, 2022 at 11:53:02 AM EDT, Joe Subich, W4TV <lists@...> wrote:
Are you loading a workspace at startup? If so, update that workspace before closing but *after* you have recreated all of your user defined controls. 73, ... Joe, W4TV
On 2022-07-05 11:39 AM, nk4l wrote:
> Good morning, just upgrade Commander to 15.4.4 and all my User defined > controls are gone so I re-due them but every time I shot down and turn > it back on what I did disappears again?, any thought and how to save it. > > Thanks. Jose NK4L > > -- > jose gonzalez -- jose gonzalez
|
|
|
|
nk4l
Thanks Joe 73
On Tuesday, July 5, 2022 at 12:03:32 PM EDT, nk4l <nk4l@...> wrote:
hello Joe no it was not happening before now I set up up all my preferences and when I close and re-open the define controls are gone but the sliders are ok.
On Tuesday, July 5, 2022 at 11:53:02 AM EDT, Joe Subich, W4TV <lists@...> wrote:
Are you loading a workspace at startup? If so, update that workspace before closing but *after* you have recreated all of your user defined controls. 73, ... Joe, W4TV
On 2022-07-05 11:39 AM, nk4l wrote:
> Good morning, just upgrade Commander to 15.4.4 and all my User defined > controls are gone so I re-due them but every time I shot down and turn > it back on what I did disappears again?, any thought and how to save it. > > Thanks. Jose NK4L > > -- > jose gonzalez -- jose gonzalez -- jose gonzalez
|
|
|
|
Dave AA6YQ
+ AA6YQ comments below
Are you loading a workspace at startup? If so, update that workspace+ User-defined controls are stored in files, so it should only be necessary to restore each "lost" control by reloading it from the appropriate file. Then terminate Commander and update your Workspace with your Commander settings, as Joe W4TV has suggested. 73, Dave, AA6YQ
|
|
|
|
nk4l
Got it thanks to all...Jose NK4L
On Tuesday, July 5, 2022 at 05:07:33 PM EDT, Dave AA6YQ <aa6yq@...> wrote:
+ AA6YQ comments below Are you loading a workspace at startup? If so, update that workspace+ User-defined controls are stored in files, so it should only be necessary to restore each "lost" control by reloading it from the appropriate file. Then terminate Commander and update your Workspace with your Commander settings, as Joe W4TV has suggested. 73, Dave, AA6YQ -- jose gonzalez
|
|
|
|
d_ziolkowski
Dave- I had the same issue when I upgraded Commander to 15.4.4. After the update, a control sequences file did load, but it was not the same control sequences that were present before the update. The file that loaded was saved under Multiradio/user-defined control sets, radio 1. The file itself was in Commander/control sets. I searched for the proper file, but could not find one, could it have been deleted? I looked at backups I have and found none. I then took Commander back a version and all was back to the proper sequences. I reviewed all the documentation, but I did not find a solution. One question I had was if a control set file was needed if only one radio was set up, I could not find an answer. In the past I had 2 radios set up, now only only, an FT450. Then I updated again, commander 15.4.4 still opened with the wrong sequences. Finally I did a workspace restore and the proper sequences were there. But I still can't find the proper control sequence file. If there is a file of the sequences I cannot locate it. I believe it should be under Commander/control sets. I might add this has never happened before when I upgraded Commander, all sequences loaded without issue. So it seems like they are saved in the registry? All is good now, but I do want to create a proper control sequences file, hope to get to it in a few days. This did happen a couple weeks ago, hopefully I recreated the sequence of events faithfully. Thanks Dan KC2STA
On Tue, Jul 5, 2022 at 5:07 PM Dave AA6YQ <aa6yq@...> wrote: + AA6YQ comments below --
Dan Ziolkowski KC2STA SKCC #4290T Ubuntu LINUX
|
|
|
|
Dave AA6YQ
+ AA6YQ comments below
+ Each control sequence is stored in a file. + If you are controlling a single primary transceiver, Commander uses the Windows Registry to remember the filename associated with each control sequence. + A Commander update provides a new executable file. The update process cannot not alter the Windows Registry. + If you are controlling multiple primary transceivers, the "User-defined Control Sets" panel on the Configuration window's Multi-Radio tab lets you specify a "User-defined Control Set" for each Radio. A "User-defined Control Set" is a file that specifies the pathname of each user-defined control sequence and slider to be used when the radio associated with that User-defined Control Set is selected. + The reference documentation for user-defined control sets is here: https://www.dxlabsuite.com/commander/Help/ControllingMultipleRadios.htm + The file in which a user-defined control set is saved can be viewed with a text editor, but should only be modified via Commander. 73,
|
|
|
|
d_ziolkowski
Dave- So as I thought, the single radio control sequences are stored in the registry. thanks for the info Dan KC2STA
On Tue, Jul 5, 2022 at 7:49 PM Dave AA6YQ <aa6yq@...> wrote: + AA6YQ comments below --
Dan Ziolkowski KC2STA SKCC #4290T Ubuntu LINUX
|
|
|