Are DXKeeper, WSJT-X and JT-AlertX all being run with normal user (*NOT* administrator) privileges? 73, ... Joe, W4TV

*HAVE YOU READ THE HELP FOR CONFIG -> GENERAL AS I SUGGESTED?* It sounds as if you have not restored your previous setting for the "Log QSOs Tab's Default Focus" setting. One option is to place the de

Have you checked "Require Edit to Modify QSOs" in Config -> General? Have you made any other changes in Config -> General? I suggest reviewing the built-in help file for Config -> General. 73, ... Joe

No. 73, ... Joe, W4TV

Navigate to the folder in which Commander is installed. Open Radios.txt and look for the "Radio=FSDR-xxxx" listings at the bottom. If the file does not contain: FSDR-1000, FSDR-1500, FSDR-3000, FDSR-5

TS-890 Instruction Manual, page 3-4 ... Menu 2-07 ... FSK Keying Polarity Set to ON if currently Off. Kenwood (and Yaesu) generally expect a logic high (+5V or open circuit) on the FSK line for MARK.

If I recall correctly, he can simply *REMOVE* grid, lat & lon from QRZ. Looking at the "edit options" menu in QRZ, it appears that one option is "No map, no location, no grid". 73, ... Joe, W4TV

Did you set the *LOTW* Sent and Rcvd fields to "R"? 73, ... Joe, W4TV

Have you defined an override for T6AA? Does it have the correct grid and/or Lat/Lon? 73, ... Joe, W4TV

1) Save your log display layout to a file (Config -> Layout). 2) Create a separate Log display layout (Config -> Log) for your pint out and give is a separate (unique) file name. 3) For normal operati

Yes, once properly configured the two virtual serial ports created by the Kenwood drivers are equivalent to two hardware serial port connections with the necessary hardware interfaces. Work with a loc

Do you have a connection between a *second* serial port (not the port used by Commander for CAT control) and the FSK input on the ACC jack of the TS-890? See <http://www.dxlabsuite.com/dxlabwiki/FSKCo

Are you using FSK (RTTY on the Kenwood) or AFSK (USB/DATA)? FSK requires a separate "FSK" (shift) signal from a USB/Serial port to the transceiver FSK input (ACC jack) and the TS-890 *may* not provide

Bill, You likely have an error on the "Multi-Radio" tab ... Make sure the COM port # for the SatPC32 port is set to '-' (the last entry, below COM64) so that Commander releases the CAT port when SatPC

Contact Dr. James Hall, WB4YDL <heartdoc@nwtcc.com>. Jamie is a cardiologist and active contester. I'm sure he keeps up with the issues of RFI and pacemakers/ICDs/etc. - I've seen him write on the sub

This *IS NOT* a good configuration. microKEYER makes use of the *HARDWARE* PTT signal to switch the audio source from mic to sound card and the transceiver audio connection from mic to line (ACC). Usi

All callsigns held by a single operator in the same DXCC Country (for DXCC). All callsigns used by a single operator from locations within a 50 mi (IIRC) radius (for WAS). All callsigns used by a sing

Unlike N1MM+ and wsjt-x where N1MM+ suspends its polling and accepts frequency from wsjt-x, Commander is *never* "passive" - Commander is *always* polling for frequency, s-meter, etc. Dave, as an alte

DXKeeper does not recognize eQSL's "eAwards". eQSL pseudo confirmations are only "recognized" for AG members when used for WAZ, WPX, WAE, etc. and those awards do not differentiate among, PSK, MFSK, J

Absolutely not! <MODE:4> MFSK and <MODE:4> MFSK <SUBMODE:3> FT4 are clearly different and should not represent an exact mode match. FT4 QSOs uploaded with only <MODE:4> MFSK represent uploads from def