Date   
Re: Propview?

Dave, AA6YQ <dhb@...>
 

The prefix will appear in the prediction graph title if (and only if) you
established the receiver location by entering a prefix in DXView. If you
select a lat/lon by clicking on DXView's map, or by directly entering the
lat/lon (either in DXView or PropView), then the graph title will show
lat/lon.

If someone has a way to convert a lat/lon to a prefix, let me know!

73,

Dave, AA6YQ

-----Original Message-----
From: Richard B Drake [mailto:rich@...]
Sent: Sunday, April 08, 2001 15:09 PM
To: dxlab@...
Subject: RE: [dxlab] Propview?


Ron,

Perhaps I don't understand your question. However, I wonder if you
are using DXView V1.2.7 and PropView V1.0.4. With this
combination, I am seeing the Prefix both in DXView and in the
title at the top of the prediction graph in PropView.

---
73, Rich - W3ZJ

> -----Original Message-----
> From: Ron Eberson [mailto:zx@...]
> Sent: Sunday, April 08, 2001 3:00 PM
> To: dxlab@...
> Subject: [dxlab] Propview?
>
>
>
>
> Is it posible to see the Prefix also now i see the
> degrees in the new
> version.
> The old you see the prefix can we make a choce in that.
>
> Sorry for my English i know that it's not correct.
>
> 73's Ron
>
>
> To unsubscribe from this group, send an email to:
> dxlab-unsubscribe@...
>
>
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
>
>


Yahoo! Groups Sponsor

Click for Details


To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Re: Settings

Andrew J. O'Brien <obrienaj@...>
 

meanwhile I just pointed to my QTH on the map, fine tuned a little and it
works well. It helps that I live right next to a great lake, easy to spot
on the world map.

----- Original Message -----
From: "Dave, AA6YQ" <dhb@...>
To: <dxlab@...>
Sent: Sunday, April 08, 2001 15:10
Subject: RE: [dxlab] Settings


Its a defect, Ben. An update will be available shortly.

73,

Dave, AA6YQ
-----Original Message-----
From: Bernard Backaert [mailto:bbackaert@...]
Sent: Sunday, April 08, 2001 14:43 PM
To: dxlab@...
Subject: Re: [dxlab] Settings


Hello Andy,

There are no dumb questions only dump answers HI

I am new to dxview and I have also problems to enter my coordinates .
The
program tells my always " illegal"

What I'm missing ,


Best 73

Ben ON5GQ
**********************************
Bernard Backaert
Amateur Radio Station ON5GQ
Email : bbackaert@...
: on5gq@...
Please visit : www.qsl.net/on5gq
**********************************
----- Original Message -----
From: "Andrew J. O'Brien" <obrienaj@...>
To: <dxlab@...>
Sent: Sunday, April 08, 2001 8:20 PM
Subject: [dxlab] Settings


> Okay sorry for the dumb question....
>
> I cannot program in my longitude / latitude. The help file tells me
to
> enter 00 '00 N (or whatever) but DXVIEW does not allow me to enter the
'
> character. I can enter 00.00 but it will not let me enter a N,S,E, or
W.
>
> Andy KB2EOQ
>
>
> To unsubscribe from this group, send an email to:
> dxlab-unsubscribe@...
>
>
>
> Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
>
>
>
>


Yahoo! Groups Sponsor

Click for Details


To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.






To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

DXView 1.2.8 is available

Dave, AA6YQ <dhb@...>
 

This release corrects the defect that prevents direct entry of QTH latitude
and longitude in the Configuration window's General tab.

If you've already installed DXView, you can upgrade by downloading
http://www.qsl.net/dxview/DXView128Update.exe - store it in your DXView
folder and execute it; you can then run the extracted DXView128.exe .

73,

Dave, AA6YQ

Re: Propview?

Richard B Drake
 

And if the Lat/Lon is for a boat in the middle of the Pacific,
what's the prefix? Good trick if you could do it :-)

----
73, Rich - W3ZJ

-----Original Message-----
From: Dave, AA6YQ [mailto:dhb@...]
Sent: Sunday, April 08, 2001 3:14 PM
To: dxlab@...
Subject: RE: [dxlab] Propview?


The prefix will appear in the prediction graph title if
(and only if) you
established the receiver location by entering a prefix
in DXView. If you
select a lat/lon by clicking on DXView's map, or by
directly entering the
lat/lon (either in DXView or PropView), then the graph
title will show
lat/lon.

If someone has a way to convert a lat/lon to a prefix,
let me know!

73,

Dave, AA6YQ
-----Original Message-----
From: Richard B Drake [mailto:rich@...]
Sent: Sunday, April 08, 2001 15:09 PM
To: dxlab@...
Subject: RE: [dxlab] Propview?


Ron,

Perhaps I don't understand your question. However, I
wonder if you
are using DXView V1.2.7 and PropView V1.0.4. With this
combination, I am seeing the Prefix both in DXView and in the
title at the top of the prediction graph in PropView.

---
73, Rich - W3ZJ

> -----Original Message-----
> From: Ron Eberson [mailto:zx@...]
> Sent: Sunday, April 08, 2001 3:00 PM
> To: dxlab@...
> Subject: [dxlab] Propview?
>
>
>
>
> Is it posible to see the Prefix also now i see the
> degrees in the new
> version.
> The old you see the prefix can we make a choce in that.
>
> Sorry for my English i know that it's not correct.
>
> 73's Ron
>
>
> To unsubscribe from this group, send an email to:
> dxlab-unsubscribe@...
>
>
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
>
>


Yahoo! Groups Sponsor

Click for Details


To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo!
Terms of Service.






To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/

Propview

Ron Eberson <zx@...>
 

Sorry a mastake from my site about prefix etc.
I am to fast with make a e mail about something i must look first before ask
and mailing.

Let we think thats Europe same on the band if there is DX hahahah

DXView 1.2.8

Richard B Drake
 

Starting DXView 1.2.8 while DXKeeper is already running fails to
establish communications between the two. One has to shut down
DXKeeper and restart it to establish the connection.

-----
73, Rich - W3ZJ
www.w3zj.com

Re: DXView 1.2.8

Dave, AA6YQ <dhb@...>
 

I just tried this several times without failure. I did "improve" the code in
this area for 1.2.7, so a regression may have been introduced. I'll check it
out on a few other configurations and inspect the code again.

73,

Dave, AA6YQ

-----Original Message-----
From: Richard B Drake [mailto:rich@...]
Sent: Sunday, April 08, 2001 16:13 PM
To: Dxlab
Subject: [dxlab] DXView 1.2.8


Starting DXView 1.2.8 while DXKeeper is already running fails to
establish communications between the two. One has to shut down
DXKeeper and restart it to establish the connection.

-----
73, Rich - W3ZJ
www.w3zj.com


Yahoo! Groups Sponsor

Click for Details


To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Re: DXKeeper 122

Dave, AA6YQ <dhb@...>
 

Hmm, I can't replicate this one either. Are you doing anything in particular
between the first lookup and the correction to the callsign? Does it fail
every time?

73,

Dave, AA6YQ

-----Original Message-----
From: Richard B Drake [mailto:rich@...]
Sent: Sunday, April 08, 2001 14:51 PM
To: Dxlab
Subject: [dxlab] DXKeeper 122


Dave,

I have occasionally experienced a problem with DXKeeper hanging up
on me, it seems to get stuck in an infinite loop. It took me a
while to figure out how to reproduce it, but here it is. If I
enter a call in the capture window and press enter to do the look
up, then later without clearing the capture window I go back and
make a correction to the callsign and press enter again,
everything seems fine but when I go to log that QSO, DXKeeper is
hung up.

-----
73, Rich - W3ZJ
www.w3zj.com


Yahoo! Groups Sponsor



To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Re: DXKeeper 122

Richard B Drake
 

Yup, every time. I tried shutting down all other applications to
see if that had any affect - it didn't.

1) Type W7JJ into the capture window (a fictitious call sign, not
in log) and press enter.

2) Correct the callsign to W7JJK, press enter again.

3 Click "log". Nothing happens, moving the cursor to the DXKeeper
window displays a permanent hour glass cursor.

4) Shut down DXKeeper and restart, the QSO is not logged.

-----
73, Rich - W3ZJ

-----Original Message-----
From: Dave, AA6YQ [mailto:dhb@...]
Sent: Sunday, April 08, 2001 4:45 PM
To: dxlab@...
Subject: RE: [dxlab] DXKeeper 122


Hmm, I can't replicate this one either. Are you doing
anything in particular
between the first lookup and the correction to the
callsign? Does it fail
every time?

73,

Dave, AA6YQ
-----Original Message-----
From: Richard B Drake [mailto:rich@...]
Sent: Sunday, April 08, 2001 14:51 PM
To: Dxlab
Subject: [dxlab] DXKeeper 122


Dave,

I have occasionally experienced a problem with
DXKeeper hanging up
on me, it seems to get stuck in an infinite loop. It took me a
while to figure out how to reproduce it, but here it is. If I
enter a call in the capture window and press enter to
do the look
up, then later without clearing the capture window I
go back and
make a correction to the callsign and press enter again,
everything seems fine but when I go to log that QSO,
DXKeeper is
hung up.

-----
73, Rich - W3ZJ
www.w3zj.com


Yahoo! Groups Sponsor



To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo!
Terms of Service.






To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/

Re: DXView 1.2.8

Richard B Drake
 

OK, a little more info on this one. It works OK as long as
PropView is not running. With PropView running it fails.

73, Rich - W3ZJ

-----Original Message-----
From: Dave, AA6YQ [mailto:dhb@...]
Sent: Sunday, April 08, 2001 4:38 PM
To: dxlab@...
Subject: RE: [dxlab] DXView 1.2.8


I just tried this several times without failure. I did
"improve" the code in
this area for 1.2.7, so a regression may have been
introduced. I'll check it
out on a few other configurations and inspect the code again.

73,

Dave, AA6YQ
-----Original Message-----
From: Richard B Drake [mailto:rich@...]
Sent: Sunday, April 08, 2001 16:13 PM
To: Dxlab
Subject: [dxlab] DXView 1.2.8


Starting DXView 1.2.8 while DXKeeper is already
running fails to
establish communications between the two. One has to shut down
DXKeeper and restart it to establish the connection.

-----
73, Rich - W3ZJ
www.w3zj.com


Yahoo! Groups Sponsor

Click for Details


To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo!
Terms of Service.






To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/

Re: DXKeeper 122

Richard B Drake
 

A little more info on this one. If the original callsign is in the
log, there is no problem. It's only when the callsign is not there
and the log display screen is empty after pressing enter. In this
case you actually don't even have to change the callsign in the
capture window, just press enter a second time and it's in
trouble.

73, Rich - W3ZJ

-----Original Message-----
From: Richard B Drake [mailto:rich@...]
Sent: Sunday, April 08, 2001 5:07 PM
To: dxlab@...
Subject: RE: [dxlab] DXKeeper 122


Yup, every time. I tried shutting down all other applications to
see if that had any affect - it didn't.

1) Type W7JJ into the capture window (a fictitious call
sign, not
in log) and press enter.

2) Correct the callsign to W7JJK, press enter again.

3 Click "log". Nothing happens, moving the cursor to
the DXKeeper
window displays a permanent hour glass cursor.

4) Shut down DXKeeper and restart, the QSO is not logged.

-----
73, Rich - W3ZJ

-----Original Message-----
From: Dave, AA6YQ [mailto:dhb@...]
Sent: Sunday, April 08, 2001 4:45 PM
To: dxlab@...
Subject: RE: [dxlab] DXKeeper 122


Hmm, I can't replicate this one either. Are you doing
anything in particular
between the first lookup and the correction to the
callsign? Does it fail
every time?

73,

Dave, AA6YQ
-----Original Message-----
From: Richard B Drake [mailto:rich@...]
Sent: Sunday, April 08, 2001 14:51 PM
To: Dxlab
Subject: [dxlab] DXKeeper 122


Dave,

I have occasionally experienced a problem with
DXKeeper hanging up
on me, it seems to get stuck in an infinite loop.
It took me a
while to figure out how to reproduce it, but here
it is. If I
enter a call in the capture window and press enter to
do the look
up, then later without clearing the capture window I
go back and
make a correction to the callsign and press enter again,
everything seems fine but when I go to log that QSO,
DXKeeper is
hung up.

-----
73, Rich - W3ZJ
www.w3zj.com


Yahoo! Groups Sponsor



To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo!
Terms of Service.






To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/




To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/

Re: DXView 1.2.8

Bernard Backaert <bbackaert@...>
 

Hello Dave,

Just to let you know that here everything is now working fine, DXview and
Propview, no problems anymore to enter new coordinates

Thanks

Best 73 Ben ON5GQ

**********************************
Bernard Backaert
Amateur Radio Station ON5GQ
Email : bbackaert@...
: on5gq@...
Please visit : www.qsl.net/on5gq
**********************************

DXKeeper 1.2.2 "Show control explanations"

Richard B Drake
 

DXkeeper does not remember from one session to the next that I
have turned off "Show control explanations"

-----
73, Rich - W3ZJ
www.w3zj.com

FW: PropView 1.0.5 is available

Dave, AA6YQ <dhb@...>
 

This release corrects the defect responsible for generating a runtime error
if DXView is not installed.

You can upgrade to PropView 1.0.5 by downloading and running
www.qsl.net/propview/PropView105Update.exe -- it will install
PropView105.exe , which
you can then run.

73,

Dave, AA6YQ

Re: DXKeeper 1.2.2 "Show control explanations"

Dave, AA6YQ <dhb@...>
 

Will be fixed in 1.2.3.

73,

Dave, AA6YQ

-----Original Message-----
From: Richard B Drake [mailto:rich@...]
Sent: Monday, April 09, 2001 10:05 AM
To: Dxlab
Subject: [dxlab] DXKeeper 1.2.2 "Show control explanations"


DXkeeper does not remember from one session to the next that I
have turned off "Show control explanations"

-----
73, Rich - W3ZJ
www.w3zj.com


Yahoo! Groups Sponsor

>>
Enter Business Search Term above





To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Re: FW: PropView 1.0.5 is available

Richard B Drake
 

Dave,

This does not correct the problem where the connection between
DXKeeper and DXView is not established when you start DXView after
both DXKeeper and PropView are already running.

I also have problems at other times where the communication
between the various applications seems to break down but I haven't
yet been able to identify a consistent sequence of operations that
cause that. However, this one with DXKeeper and PropView followed
by DXView is very consistent.

----
73, Rich - W3ZJ

-----Original Message-----
From: Dave, AA6YQ [mailto:dhb@...]
Sent: Tuesday, April 10, 2001 12:20 AM
To: I. J. Roberts; bobrushby@...; 0586-37190@...;
wp.schwarzott@...; office@...;
johnki4ro@...
Cc: dxlab@...; Dave AA6YQ
Subject: [dxlab] FW: PropView 1.0.5 is available


This release corrects the defect responsible for
generating a runtime error
if DXView is not installed.

You can upgrade to PropView 1.0.5 by downloading and running
www.qsl.net/propview/PropView105Update.exe -- it will install
PropView105.exe , which
you can then run.

73,

Dave, AA6YQ



To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/


DXView

Ron Eberson <zx@...>
 

-Dave is it posible to make a second button on the window at GO in DXView?
this button can copy the call to DXKeeper and so you can use it direct now i
must type the call again in DXKeeper also i can use Propview direct.

Ron

Re: DXView

Dave Bernstein <dhb@...>
 

Certainly. But I'd like to track down and correct the DXView-PropView-
DXKeeper interaction problem, as well as the DXKeeper "misbehaviour"
issue first.

Unfortunately, I have an XYL-driven furniture repair project that
takes precedence over both of these, but it shouldn't involve more
than a few hours work. If the above defects were showstoppers, I
might apply for a variance, but...

73,

Dave, AA6YQ

--- In dxlab@y..., "Ron Eberson" <zx@c...> wrote:


-Dave is it posible to make a second button on the window at GO in
DXView?
this button can copy the call to DXKeeper and so you can use it
direct now i
must type the call again in DXKeeper also i can use Propview direct.

Ron

Re: DXView

Richard B Drake
 

Oh! I suspect that most of us are well aware that you can only put
off the honey do issues for just so long before the roof caves in
:-))

------
73, Rich - W3ZJ

-----Original Message-----
From: Dave Bernstein [mailto:dhb@...]
Sent: Tuesday, April 10, 2001 1:21 PM
To: dxlab@...
Subject: [dxlab] Re: DXView


Certainly. But I'd like to track down and correct the
DXView-PropView-
DXKeeper interaction problem, as well as the DXKeeper
"misbehaviour"
issue first.

Unfortunately, I have an XYL-driven furniture repair
project that
takes precedence over both of these, but it shouldn't
involve more
than a few hours work. If the above defects were
showstoppers, I
might apply for a variance, but...

73,

Dave, AA6YQ

--- In dxlab@y..., "Ron Eberson" <zx@c...> wrote:


-Dave is it posible to make a second button on the
window at GO in
DXView?
this button can copy the call to DXKeeper and so you
can use it
direct now i
must type the call again in DXKeeper also i can use
Propview direct.

Ron

To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/


Icom RS232 interface from KG7SG

Tom Brouard <stagehand@...>
 

I am running CI-V Commander version 1.2.2 using the KG7SG interface I just
made. I am able to control the ICOM 746 via the computer but I am not able
to receive any data from the radio.

I have double checked all wiring and software and radio config settings with
no luck.

I am still suspicious that it is in the wiring but I am hoping that it is
something simple in the software or at the radio that I may have overlooked.

Suggestions from any is gratefully welcomed

Thank you

73 de KB2VNB