+ AA6YQ comments below + Is there an errorlog.txt file in your SpotCollector folder? If so, please attach this file to an email message, and send the message to me via aa6yq (at) ambersoft.com

When I click on the "Need" filter button on SpotCollector the listing goes blank even though there were highlighted entries that I need. When I click on the "X" button to clear the filter none of the

Thanks for sending me your errorlog, Chip. The entry 07-Aug-2022 19:41:21 > program error 285 in module PSKMinilog.LogQSO, State = 89: Foreign application won't perform DDE method or

+ AA6YQ comments below Although I do not own an RF2K I have checked the available information some time ago. An english manual is available at

I have a question ... RFKIT & Commander work fine . However this thread has me checking my settings...   commander indeed is set to 12060  for  127.0.0.1 AND rfkit also 12060 to xxx.183 Also

You will also need to provide the IP address of the RF2K, 127.0.0.1 is the "loopback" address on the PC running Commander and will not reach an external device. 73, ... Joe, W4TV

Although I do not own an RF2K I have checked the available information some time ago. An english manual is available at https://rf-kit.de/files/User_Manual_RF2K-S_ENG_V14.pdf

+ AA6YQ comments below + I went looking for documentation that would explain how the RF2K implements "CAT data through IP (UDP)" - but found none. + Port 52002 is what Commander utilizes to

I am looking to config my rf2k amp to commander. I have been in network service in commander. i have ip address of 127.0.0.1 and port 52002. in rf2k udp port window I have 52002 and listening to

# more AA6YQ comments below Thanks for your response, Dave. The error log is attached. # Attachments are not conveyed here. Please attach the errorlog.txt file to an email message, and send the

Thanks for your response, Dave. The error log is attached. When I hit the 'log' button, it does not clear the fields in the log panel. I have manually clicked the 'start' and 'end' qso buttons. I

Note: the QSL Aging report only lists those confirmations that are still "needed." If one has requested a confirmation from P5LID by OQRS and subsequently received a confirmation via card or LotW

+ AA6YQ comments below I need some setup hints. I am using Winwarbler for PSK but when I 'log' a contact, it does not appear in DxKeeper. I have followed the Winwarbler setup guidelines in the

+ AA6YQ comments below I just sent a QSL request using OQRS, and I think it would be helpful if I could set a calendar reminder to check on the status of my request in 30 - 45 days. Would that be a

I need some setup hints. I am using Winwarbler for PSK but when I 'log' a contact, it does not appear in DxKeeper. I have followed the Winwarbler setup guidelines in the Wiki. Thanks.

Start with ... QSLSDATE < DateAdd("d",-60,Now()) and QSL_Sent='Y' and QSL_SENT_VIA = 'E' and not (QSL_RCVD in ('Y','S','V') or APP_DXKEEPER_LotW_QSL_RCVD in ('Y','S','V') This is a modification

Hi Dave - I just sent a QSL request using OQRS, and I think it would be helpful if I could set a calendar reminder to check on the status of my request in 30 - 45 days. Would that be a function that

Thanks Peter. The instruction manual does appear easier than previous version or maybe it appears clearer to me after the 2nd read. I don't understand why "W32Time, by default, only contacts servers

Hi Joe, I forgot to thank you. Thank you Dupe info. 73, Art W2NRA CWOPS #1955

+ AA6YQ comments below The 12060 UDP port being used in DXKGW is hardcoded to that base address and cannot be changed to the best of my knowledge. + That's correct. 73, Dave,