+ AA6YQ comments below + Which setting was that, Dave? I'll add a note to the documentation. 73, Dave, AA6YQ

Thanks..but I still don't get it. Don't I need to set up a button tp turn on DNR ( for example) and then a slider for the settings? Can't figure out the button settings. Jim

I had changes to used FD logging software over mesh instead of DXLab for Field Day. Thought had everything changed back but missed one port setting. Got working again. Thanks everyone. Dave WA7DH

Thanks again, Jeff. I am running version 12.9 of SatPC32. I have just made a few (3) Qs on RS-44, I thought that SSB Sats was not going to be possible using FT-857D. Unfortunately, I only have one

It’s the ‘Label’ field on the Slider Configuration panel. Here’s my label for Monitor Level which also shows the value : Mon Level <value 0, 60> - 73 and good DX de Mike, K6MKF,

+ AA6YQ comments below I need some help with this. I got the slider to work for DNR, I think. But I don't know how to enter the text for the button to turn on DNR. Can I get an explanation on how

I need some help with this. I got the slider to work for DNR, I think. But I don't know how to enter the text for the button to turn on DNR. Can I get an explanation on how to enter the text into

Hi Rafael, from the manual.... SatPC32 updates it's calculations internally once per second. With previous program versions this speed couldn't be changed. Beginning with

In the last section of the message below, I meant to say + I suggest that you read the first paragraph of the "Reference Documentation" section of "Getting Started with DXLab"

+ AA6YQ comments below Gee, I was excited to see that I could select the fields I needed in the capture window. But, I was very disappointed when I found out I can't put in the date and time. I use

Gee, I was excited to see that I could select the fields I needed in the capture window. But, I was very disappointed when I found out I can't put in the date and time. I use a voice recorder to log

+ AA6YQ comments below On 7/8 my DXLabs programs began not opening up properly and opening one sometimes made another disappear. Maybe DXKeeper will open, then Launcher will disappear, etc. with no

On 7/8 my DXLabs programs began not opening up properly and opening one sometimes made another disappear. Maybe DXKeeper will open, then Launcher will disappear, etc. with no error messages, at least

+ AA6YQ comments below+ On the Configuration window's "World Map" tab, click the Enable button in the "Built-in Cylindrical Equidistant" panel Also is there a means by which the Worked/Confirmed

In DXView, Config, World Map I have DXAtlas enabled and would like to know how to disable it? I cannot get rid of it by clicking on the bullet. With it turned on I keep getting the QSO Lines and it

+ AA6YQ comments below + Seen Note #4 in the release note I posted here when i announced DXKeeper 16.1.9: https://www.dxlabsuite.com/dxkeeper/ReleaseNotes/1619.txt 73, Dave, AA6YQ

I saw mention on the reflector that the Capture window had changed. I don’t see any recognizable change and I installed the latest DXK upgrade a few days ago, Maybe I wasn’t paying attention.

Thanks for the hint, Jeff. Actually, increasing the CAT Tuning rate to a larger number on SatPC32 makes the radio to take longer time before it flickers again....quite enough seconds to hear the

+ AA6YQ comments below + Please attach the errorlog.txt file from your DXKeeper folder to an email message, and send the message to me via aa6yq (at) ambersoft.com + By the way, sending me an

Dave/Joe, Thanks for the replys. Dave, have been using wsjt-x with DXKeeper for about six months now, prior to that had JTXalert involved. I honestly don't remember when this problem began, mainly