Is there a recommended way to designate POTA QSO's in DXKeeper ? Currently I am just making a note of the Park number in the Comments field along with the abbreviation POTA. 73 Mark N1UK

hmm ... there are usb to relais boards available ... wit 1, 2, 4, 8 or even 16 relais maybe easier as using lpt cable and rolling your own pcb with relais?!? dg9bfc sigi Am 18.03.2021 um 22:22

There is a Hardware & Software solution for your problem. FreqEz is a raspberry Pi hat and software set that reads the UDP data from DXLab Commander or N1MM contesting software and sends the frequency

# More AA6YQ comments below # That would remain the user's responsibility before making a USACA submission. 73, Dave, AA6YQ

+ AA6YQ comments below + Commander's Secondary CAT Port can be configured to make a second transceiver's frequency and mode track that of the current Primary transceiver. See the "Secondary CAT Port"

Simon, Last summer I designed and built a unit to do automatic antenna switching to take advantage of the external device that Dave pointed out. It works FB. I can send you the schematic and

Please advise how to setup multiple rigs synced for diversity receiption on different ant to reduce fading. Rigs are icom, sdruno (emulate ts480), sdr console (emulate ts2000) Can "manual master"

All instances of a given independent city would need to be changed at the same time. USCA rules only allow a one time selection for each independent city (one can not use multiple QSOs for

+ AA6YQ comments below Many thanks for advises. Can laptop pc be used with "usb to lpt convertion cable"? Example, https://www.amazon.com/StarTech-com-USB-Parallel-Printer-Adapter/dp/B002DUEFHY +

No. LPT Support in Commander is memory mapped. The USB to LPT cables are serial devices and rely on a serial driver in the operating system with shift register output. Not currently

Hi Dave, Many thanks for advises. Can laptop pc be used with "usb to lpt convertion cable"? Example, https://www.amazon.com/StarTech-com-USB-Parallel-Printer-Adapter/dp/B002DUEFHY The last line in

Hi Bill, com port is ok. I have several USB > Serial adapter cables, have used them for several years on different projects with no problems. I suspect the ct62 (din to db9 cable). I have a new

What does the device manager show? Could you be suffering the effects if the dreaded cloned prolific usb device driver impact?

Thanks Dave, All the settings are correct. I suspect the ct62 cable. I got it cheap on ebay from an off shore vendor. I am going to get one from HRO and try again. I want to use this radio mobile

+ AA6YQ comments below Planning for a home brew relay box to route the rig to diffetent ant depends on band. Can the software send 5 Volts on off signal via a hardware box? + Yes. See "Controlling

+ AA6YQ comments below Any one using commander control for a Yeasu ft857 xcvr. I have tried using straight thru and cross over adapter just in case. I am using a CT62 cable I got on EBay(ugh!). +

Planning for a home brew relay box to route the rig to diffetent ant depends on band. Can the software send 5 Volts on off signal via a hardware box? Of course, it can be manual control if above not

+ AA6YQ comments below Yes, it is best that N1MM+ export *ALL DATA* in ADIF standard format rather than APP_N1MM_EXCHANGE# as it does presently. Unfortunately, with State QSO Parties one has the

+ AA6YQ comments below Actually there are 4 QPs that weekend, 7qp, inqp, neqp, and Delaware qp. From a rover perspective, which is what this discussion is about, it really doesn't matter how many

+ AA6YQ comments below I moved it to 25ms as suggested and have yet to see the error, so this change seems to be helping. + With a USB connect, the primary CAT baud rate set to 115200, and the