+ AA6YQ comments below Hi Dave and Ian, Just submitted my second batch of logs using my second call VE3TJB (540 Qsos) Upload was perfect again. After sync lotw qsos I now got message 626 Qsos

Hi Dave and Ian, Just submitted my second batch of logs using my second call VE3TJB (540 Qsos) Upload was perfect again. After sync lotw qsos I now got message 626 Qsos processed (How come that

Joe, WSJT-X supports short-codes and in modes like JT65 they are not merely historical artefacts, they are a very efficient mechanism of passing a 3-bit binary piece of

Be sure the date pf the certificate you are using covers the dates of the QSOes being uploaded. Outlook Laptop Gil W0MN Hierro candente, batir de repente 44.08226N 92.51265W EN34rb

The "shorthand" reports are becoming less frequently used as more users adopt WSJTX to replace the older WSJT due to the automation built into WSJT. As Bill points out the shorthand reports are an

I think it should be for JT65 EME only, if anything. MS and Tropo these days would be using modes that do not use that form of shorthand (MSK144, etc). Where does this "default" come into play

Hi Dave, I am not convinced, short codes do get used for EME on some bands but I would not necessarily say it is the default position. Also the only report is O, there is no report of RO as that is

# even more AA6YQ comments below * more AA6YQ comments below + Are "OOO and RO" appropriate for JT65 in all cases, or only when the propagation mode is set to EME? Only for EME *

+ AA6YQ comments below Hi Ian.....This batch was the oldest of 3 batches based on my first callsign VE3NKZ and based on its specific myqthid. The year range is old covering contacts from 1981 to

Hi Ian.....This batch was the oldest of 3 batches based on my first callsign VE3NKZ and based on its specific myqthid. The year range is old covering contacts from 1981 to early 1990. I had hand

Hi Dave, those types of reports are optional even in JT65 mode. In general they are used when fixed dual alternating tones are used instead of encoded messages for the acknowledgement

# AA6YQ comments below It's OOO (Oscar's), not 000 (zeroes) (similarly RO, not R0). Somewhat described here: http://www.arrl.org/files/file/18JT65.pdf # Thanks, Iain! 73,

It's OOO (Oscar's), not 000 (zeroes) (similarly RO, not R0). Somewhat described here: http://www.arrl.org/files/file/18JT65.pdf 73, ~iain / N6ML

* more AA6YQ comments below * Thanks, Joe. With the propagation mode set to EME, are "OOO and RO" appropriate as default signal reports for all K1JT modes, or just JT65? * 000 is the default "RST

Looks like 7600 isn’t supported. I think it’s just the SDR rigs. https://www.dxlabsuite.com/dxlabwiki/SpectrumWaterfallIcom

+ AA6YQ comments below + The IC-7600 cannot report spectrum data via its CI-V bus, and so is not supported by Commander's Spectrum-Waterfall window. To use this window, you need an IC-705, IC-7300,

Only for EME K1JT modes are very resistant to default signal reports as the typical report is a signal level between MDS for the submode and somewhere up to +20 (representing the signal to noise

and if so link to info. -- Norm WA4ZXV EM73vw

+ AA6YQ comments below One more item. The default signal reports (599) for JT65x don't make any sense. It would be great if the defaults could be changed to OOO and RO. is there a way to do this with

+ AA6YQ comments below I am trying to set Your Station to Residential and clicking on the button does not change it; any hints? + On the Parameters tab of PropView's Main window, the DX station's